1. DL manuals
  2. Oki
  3. Storage
  4. C 9650dn
  5. User Manual

Oki C 9650dn User Manual

Summary of C 9650dn

  • Page 2

    C9650 user’s guide 2 copyright information copyright © 2008 by oki data. All rights reserved document information ________________________________ c9650 user’s guide p/n 59306401 revision 1.2 august, 2008 disclaimer__________________________________________ every effort has been made to ensure that ...

  • Page 3

    C9650 user’s guide> 3 c ontents notes, cautions and warnings! . . . . . . . . . . . . . . . . 6 safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . 6 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 features . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    C9650 user’s guide> 4 connecting the parallel interface . . . . . . . . . . . 47 connecting the usb interface . . . . . . . . . . . . . 47 connecting the network interface . . . . . . . . . . 48 using the drivers cd . . . . . . . . . . . . . . . . . . . . . 49 operation . . . . . . . . . . . . . . ....

  • Page 5

    C9650 user’s guide> 5 appendix a – display panel messages . . . . . . . . 105 appendix b – menu system . . . . . . . . . . . . . . . . 107 configuration. . . . . . . . . . . . . . . . . . . . . . . . . . .108 print page count . . . . . . . . . . . . . . . . . . . . . .108 finisher count . . . . . . ...

  • Page 6

    C9650 user’s guide> 6 n otes , cautions and warnings ! Note a note provides additional information to supplement the main text. S afety warnings please be careful to read and understand the safety warnings on the following pages before operating the printer. Illustrations illustrations and component...

  • Page 7

    C9650 user’s guide> 7 warning! Ensure all warning and instruction labels on the product are read, understood and followed in order to prevent any risk of injury. Ensure this and all other documentation is both read carefully and retained for future reference. This printer unit weighs 167.5 lbs (76kg...

  • Page 8

    C9650 user’s guide> 8 warning! This product has an earthed plug as a safety feature and will only connect to an earthed socket. Do not attempt to defeat the earthing or there is a risk of fire or shock. If using an extension cable or power strip ensure that the total current rating (amperes) of all ...

  • Page 9

    C9650 user’s guide> 9 warning! Use only the power cable supplied. Using a power cable not intended for this product may lead to fire or electric shock. To avoid risk of fire and electric shock, do not use the power cable supplied with this product for any other electrical equipment. If you do not co...

  • Page 10

    C9650 user’s guide> 10 warning! If any liquid (for example water) is allowed to enter the printer, there is a risk of fire. Unplug the mains connector and contact your dealer. Do not place containers containing liquid on the printer as electric shock, fire and/or injuries may occur. If any foreign o...

  • Page 11

    C9650 user’s guide> 11 warning! Risk of explosion if battery is replaced by an incorrect type. Do not touch the battery. Printer battery should not require replacement during the life of the printer. After installing additional memory or a hard disk drive, the cover door must be closed and secured t...

  • Page 12

    C9650 user’s guide> 12 i ntroduction congratulations on buying an oki color printer. Your new printer is designed with advanced features to give you clear, vibrant color prints and crisp black and white pages at high speed on a range of print media for the office. There are three different models av...

  • Page 13

    C9650 user’s guide> 13 additionally, the following optional features are available: > automatic two-sided (duplex) printing for economical use of paper and compact printing of larger documents note this optional feature is only applicable to the c9650n. > hard disk drive enables spooled and verified...

  • Page 14

    C9650 user’s guide> 14 a bout this guide note images used in this manual may include optional features that your printer does not have installed. This manual is your user’s guide (check the web site, my.Okidata.Com, for the most up-to-date version) for your printer and forms part of the overall user...

  • Page 15

    C9650 user’s guide> 15 > online help : online information accessible from the printer driver and utility software. S oftware supplied cds: > drivers and utilities contains drivers and application software for use by a general user. > network and administrator utilities contains software for use by s...

  • Page 16

    C9650 user’s guide> 16 o nline usage this guide is intended to be read on screen using an adobe acrobat reader. Use the navigation and viewing tools provided in acrobat. You can access specific information in two ways: > in the list of bookmarks down the left hand side of your screen, click on the t...

  • Page 17

    C9650 user’s guide> 17 (c) [pages from] and [to], (3), for the range of pages you specify by entering their page numbers. 3. Click on [ok]..

  • Page 18

    C9650 user’s guide> 18 p rinter and paper overview o pening and closing the top cover to open the top cover, squeeze the top cover handle (1) to release the catch and raise the cover. Caution! To gain access to the inside of the printer, ensure that the top cover is fully opened. 1.

  • Page 19

    C9650 user’s guide> 19 to close the top cover, push gently (1) until the cover stops midway and then push harder (2) to close the cover completely. Ensure that the cover is securely closed. I dentifying major components the major components of your printer are identified in the graphics below. 1. Pa...

  • Page 20

    C9650 user’s guide> 20 9. Top cover handle 10. Face-down stacker 11. Power (on/off) switch 1 2 3 4 5 6 7 8 9.

  • Page 21

    C9650 user’s guide> 21 12. Face-up stacker 13. Interface unit 14. Network interface connector 10 11 12.

  • Page 22

    C9650 user’s guide> 22 15. Parallel interface connector 16. Usb interface connector 17. Power connector 18. Ventilation openings 19. Image drum cartridge and toner cartridge (cyan) 20. Image drum cartridge and toner cartridge (magenta) 13 17 18 14 15 16.

  • Page 23

    C9650 user’s guide> 23 21. Image drum cartridge and toner cartridge (yellow) 22. Image drum cartridge and toner cartridge (black) 23. Toner cartridge 24. Image drum cartridge 25. Fuser unit 26. Led heads 27. Belt unit 28. Drum basket handle 19 20 21 22 23 24 25 26.

  • Page 24

    C9650 user’s guide> 24 29. Drum basket 27 28 29.

  • Page 25

    C9650 user’s guide> 25 p aper recommendations your printer will handle a variety of print media, including a range of paper weights and sizes, transparencies and envelopes. This section provides general advice on choice of media, and explains how to use each type. The best performance will be obtain...

  • Page 26

    C9650 user’s guide> 26 p aper input and output information the following table relates paper parameters to input trays (tray 1 to tray 5 (numbering from the top) and mp tray) and to output areas (face-down stacker and face-up stacker). Type size weight input/ output plain paper a3, a3 nobi, a3 wide,...

  • Page 27

    C9650 user’s guide> 27 t rays and stackers t rays 1 to 5 tray 1 is the standard blank paper input tray and can hold up to 530 sheets of 20 lb (75 g/m²) paper. Additional trays, to give a total of five, can be added as an option to give a total tray capacity of 2650 sheets of 20 lb (75 g/m²) paper. I...

  • Page 28

    C9650 user’s guide> 28 f ace - down stacker the face-down stacker on the top of the printer can hold up to 500 sheets of 20 lb (80 g/m²) standard paper, and can handle paper stocks from 17 – 57 lb (64 – 216 g/m²). Pages printed in reading order (page 1 first) will be sorted in reading order (last pa...

  • Page 29

    C9650 user’s guide> 29 t ray and stacker examples l oading t rays 1 to 5 tray 1 is used in the following example. 1. Pull out the tray. 2. Press the paper rear stopper tab (1) and adjust the tab to the required paper size. 3. Fan the paper to be loaded then tap the edges of the stack on a flat surfa...

  • Page 30

    C9650 user’s guide> 30 4. Load the paper (face down and top edge towards the right for letterhead paper), press the tab (2) on the paper guide and adjust the guides (3) for a snug fit to the paper. To avoid paper jams: • do not leave space between the paper and the guides and rear stopper. • do not ...

  • Page 31

    C9650 user’s guide> 31 5. Gently push the tray back into the printer. U sing the mp t ray 1. Squeeze the handle (1) and open the multi-purpose tray. 1.

  • Page 32

    C9650 user’s guide> 32 2. Fold out the paper support section and swivel out the extension supports (2). 3. Adjust the paper guides (3) to the size of the paper being used. 4. Fan the paper to be loaded then tap the edges of the stack on a flat surface to make it flush. 5. Load the paper. • for singl...

  • Page 33

    C9650 user’s guide> 33 the printer. (the duplex unit must be installed for this function.) • envelopes should be loaded face-up with long edge into the printer. Do not select duplex printing on envelopes. • do not leave space between the paper and the guides. • do not exceed the paper capacity of ap...

  • Page 34

    C9650 user’s guide> 34 u sing the stackers face-down stacker when the face-up stacker (1) on the left side of the printer is closed (its normal position), paper is ejected to the face-down stacker on the top of the printer. Face-up stacker the face-up exit path is used for heavy paper (cardstock etc...

  • Page 35

    C9650 user’s guide> 35 2. Flip out the paper support (2). 3. Swivel out the paper support extension (3). 2 3.

  • Page 36

    C9650 user’s guide> 36 c ontrol panel the control panel can be swivelled to 90° (maximum) upwards from its base position (1) as required for ease of use. B uttons and lights the parts of the control panel are identified and briefly explained below: 1. Shutdown/restart button hold down for more than ...

  • Page 37

    C9650 user’s guide> 37 2. Ready light on: indicates ready to print flashing: indicates processing print data off: indicates unable to receive data (offline) 3. Attention light off: indicates normal operation flashing: indicates error(s) present but printing can continue on: indicates error(s) presen...

  • Page 38

    C9650 user’s guide> 38 d isplay p anel messages there are four types of display panel message: > status information > menu (functions) information > configuration information > help information s tatus information status information is associated with three printer states: in the information state, ...

  • Page 39

    C9650 user’s guide> 39 restart). Available to support staff to allow printer configurations and special functions to be set. C onfiguration information configuration information displays printer configuration information such as internal firmware versions. Menu options at each level can be scrolled ...

  • Page 40

    C9650 user’s guide> 40 the steps involved in using the menus are typically as follows: 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter user menu mode by pressing either the enter button or the up-arrow or down-arrow button and press the latter two repeatedly u...

  • Page 41

    C9650 user’s guide> 41 g etting started this section provides information to help you get started with using your printer. P rinter location check that you have sufficient space for access: > around your printer: 60cm 60cm 20cm 8in 100cm 40in 24in 24in.

  • Page 42

    C9650 user’s guide> 42 > above your printer: t urning o ff /o n t urning o ff no hard disk drive installed 1. If a hard disk drive is not installed, use the on/off switch. 70cm 28in.

  • Page 43

    C9650 user’s guide> 43 hard disk drive installed 1. If your printer has a hard disk drive installed, hold down the shutdown/restart button (1) on the control panel for more than 2 seconds to start the shutdown process. 2. When the display panel shows that you can either turn off or restart the print...

  • Page 44

    C9650 user’s guide> 44 t urning o n note if the display panel shows that you can either turn off or restart the printer, press shutdown/restart to turn on the printer. 1. If the printer is turned off (no power), use the on/off switch to turn on the printer. C hanging the display language the default...

  • Page 45

    C9650 user’s guide> 45 c hecking current settings carry out the following steps to generate a configuration report (menu map) to confirm that your printer is correctly configured. 1. Ensure that there is letter paper in tray 1 (to be used in this operation). 2. Ensure that the display panel indicate...

  • Page 46

    C9650 user’s guide> 46 i nterfaces and connection your printer is equipped with a selection of data interfaces: > parallel – for direct connection to a pc. This port requires a bi-directional (ieee 1284 compliant) parallel cable. > usb – this port requires a cable conforming to usb version 2.0 or ab...

  • Page 47

    C9650 user’s guide> 47 c onnecting the parallel interface 1. Turn off the printer and the computer. 2. Connect a parallel cable between the printer and computer. 3. Turn on the printer and then the computer. C onnecting the usb interface do not connect the usb cable at this time. You will be instruc...

  • Page 48

    C9650 user’s guide> 48 c onnecting the network interface 1. Turn off the printer and the computer. 2. Install the ferrite core to the ethernet cable as shown. Caution! Do not connect a usb cable into the network interface connector as this may lead to malfunction..

  • Page 49

    C9650 user’s guide> 49 3. Connect an ethernet cable between the printer and an ethernet hub. 4. Turn on the printer and then the computer. If your printer is to be installed as a network printer, please refer to the relevant section in the software installation guide and configuration guide for furt...

  • Page 50

    C9650 user’s guide> 50 o peration u sing the printer for full details of how to use the printer and any optional accessories to print jobs efficiently and effectively, please refer to the printing guide..

  • Page 51

    C9650 user’s guide> 51 c onsumables and maintenance this section explains how to replace consumable and maintenance items when due. As a guide, the life expectancy of these items is: > black toner — 18,500 letter pages at 5% coverage. > cyan, magenta, yellow toner— 16,500 letter pages at 5% coverage...

  • Page 52

    C9650 user’s guide> 52 c onsumable item order information m aintenance item order details item life order number toner, black 18,500 letter pages @ 5% 42918984 toner, cyan 16,500 letter pages @ 5% 42918983 toner, magenta 16,500 letter pages @ 5% 42918982 toner, yellow 16,500 letter pages @ 5% 429189...

  • Page 53

    C9650 user’s guide> 53 r eplacing consumables / maintenance items each consumable or maintenance item comes complete with its own installation details which give full instructions on replacement. You are advised to follow these instructions carefully. C leaning the led heads you are advised to clean...

  • Page 54

    C9650 user’s guide> 54 2. With an led lens cleaner or soft cloth, gently wipe each of the four heads (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 3. Close the top cover. 1 2.

  • Page 55

    C9650 user’s guide> 55 c leaning the paper feed rollers clean the paper feed rollers if paper jams frequently occur. 1. Remove items like a wrist watch or bracelet and follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Open tray 1 side cover and ...

  • Page 56

    C9650 user’s guide> 56 3. Remove tray 1 completely from the printer. 4. Gaining access through the gap left by tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. 5. Replace tray 1. 2.

  • Page 57

    C9650 user’s guide> 57 6. Return the paper guide plate to its original position and close tray 1 side cover. 7. Turn on the printer..

  • Page 58

    C9650 user’s guide> 58 c leaning the printer casing 1. Follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. 3. Use a soft dry cloth to dry the printer s...

  • Page 59

    C9650 user’s guide> 59 4. Turn on the printer. E mptying the punch chip box (p unch unit optional accessory ) when the display panel indicates that the punch chip box is full, empty the box as follows: 1. Operate the finisher lever and move the finisher away from the printer..

  • Page 60

    C9650 user’s guide> 60 2. Pull out the punch chip box, being careful to keep it level so as not to spill any chips. 3. Discard the chips in an appropriate place. 4. Replace the punch chip box carefully into the finisher..

  • Page 61

    C9650 user’s guide> 61 5. Check that the punch chip box has been replaced correctly then move the finisher back into position, being careful not to trap your fingers..

  • Page 62

    C9650 user’s guide> 62 o ptional accessories this section describes optional accessory equipment for your printer. The following accessories are available: > duplex unit (to enable two-sided printing) (c9650n only) > additional ram memory > hard disk drive (required for verified and spooled printing...

  • Page 63

    C9650 user’s guide> 63 a ccessory order information item order number duplex unit 42797201 additional ram memory 256 mb 512 mb 70050301 70050401 hard disk drive 70050501 second, third paper tray 42831301 high capacity feeder (hcf) 42831501 finisher: 4-tray 5-tray 42940201 42872701 finisher punch uni...

  • Page 64

    C9650 user’s guide> 64 i nstalling accessories each accessory (apart from the finisher) comes complete with its own documentation which gives full instructions on installation. You are advised to follow these instructions carefully. After installation, print out a menu map (configuration document) t...

  • Page 65

    C9650 user’s guide> 65 t roubleshooting g eneral if the printer display panel does not display anything or is still in stand-by mode 10 minutes after switching on, follow the printer shutdown sequence to switch it off. Check all cable connections before restarting the printer. If the problem persist...

  • Page 66

    C9650 user’s guide> 66 1. Squeeze the catch (1) on tray 1 side cover and open the cover. 2. Holding it by the tab (2), turn the paper guide outward. 3. Carefully remove the jammed paper. 2.

  • Page 67

    C9650 user’s guide> 67 4. Put the paper guide back into position and close tray 1 side cover. O pen cover , paper jam , side cover 1. If the mp tray is open, close it so that the side cover (1) is visible. 1.

  • Page 68

    C9650 user’s guide> 68 2. Pull the release lever (2) and pull open the side cover. 3. Carefully remove the jammed paper. 2.

  • Page 69

    C9650 user’s guide> 69 4. Close the side cover. O pen cover , paper jam , top cover 1. Squeeze the top cover handle (1) and open the top cover. Warning! Be careful not to touch the fuser unit which is hot after printing. 1.

  • Page 70

    C9650 user’s guide> 70 2. Squeeze the basket handle (2) and raise the drum basket. 3. Carefully remove any paper on the belt. 4. If paper is jammed in the fuser unit, push the lock lever (3) in the direction shown to release the unit. Warning! Be careful not to touch the fuser unit which may be hot ...

  • Page 71

    C9650 user’s guide> 71 holding the fuser unit (4) by the handle, lift it out of the printer and place it on a flat surface. 5. Pull up the jam release levers (5) and remove the jammed paper. 4 3 5.

  • Page 72

    C9650 user’s guide> 72 6. Carefully replace the fuser unit into the printer and turn the lock lever (6) in the direction shown to lock the fuser unit. 7. If paper is jammed near the paper exit, open the face-up stacker (7). 6 7.

  • Page 73

    C9650 user’s guide> 73 8. Open the side cover (paper exit) (8) and remove the jammed paper. 9. Close the side cover (paper exit) and then the face-up stacker. 8.

  • Page 74

    C9650 user’s guide> 74 10. Return the image drum basket (9) into position and check it is locked. 11. Close the top cover and ensure it is latched. 9.

  • Page 75

    C9650 user’s guide> 75 p aper jams – duplex unit ( if installed ) c heck duplex unit , paper jam 1. If a finisher unit is attached to your printer, operate the lever (1) of the inverter unit to separate the inverter from the printer. 2. Operate the duplex cover release button (2) and open the cover....

  • Page 76

    C9650 user’s guide> 76 3. Carefully remove any jammed paper. 4. Operate the levers (3) and pull out the duplex unit. 3 3.

  • Page 77

    C9650 user’s guide> 77 5. Holding the front top cover by the grip (4), push it gently inwards and raise it. 6. Remove any jammed paper. 4.

  • Page 78

    C9650 user’s guide> 78 7. In similar manner, check for and clear any paper jammed under the rear top cover. 8. Replace the two top covers..

  • Page 79

    C9650 user’s guide> 79 9. Raise the front cover of the duplex unit. 10. Push the duplex unit back into position..

  • Page 80

    C9650 user’s guide> 80 11. If you detached a finisher unit to gain access to the duplex unit, replace the finisher unit..

  • Page 81

    C9650 user’s guide> 81 p aper jams – f inisher ( optional accessory ) c heck f inisher , paper jam / paper remains use the help button on the printer control panel to check the number displayed. You will need this to be able to clear the paper jam. The following paragraphs explain what to do for eac...

  • Page 82

    C9650 user’s guide> 82 2. Operate the finisher lever (1) and move the finisher away from the inverter. 3. Open the finisher top cover. 1.

  • Page 83

    C9650 user’s guide> 83 4. Carefully remove any jammed paper. 5. Close the finisher top cover. 6. Move the finisher back into position and connect it to the inverter..

  • Page 84

    C9650 user’s guide> 84 594, 597, 598/ 644, 646 ( paper jam in f inisher ) 1. Operate the finisher lever (1) and move the finisher away from the inverter. 2. Open the finisher front cover (2). 1 2.

  • Page 85

    C9650 user’s guide> 85 3. Continue to turn the lower knob (3) clockwise until any jammed paper is completely ejected. 4. Remove the ejected paper. 5. Close the finisher front cover. 3.

  • Page 86

    C9650 user’s guide> 86 6. Open the finisher right side cover. 7. Carefully remove any jammed paper. 8. Close the finisher right side cover..

  • Page 87

    C9650 user’s guide> 87 9. Move the finisher back into position and connect it to the inverter. 590 ( paper jam in f inisher /p unch unit ) 1. Operate the finisher lever (1) and move the finisher away from the inverter. 1.

  • Page 88

    C9650 user’s guide> 88 2. Move the tab (2) on the right side of the finisher to align it with the mark (3). 3. Open the finisher top cover. 2 3.

  • Page 89

    C9650 user’s guide> 89 4. Carefully remove any jammed paper. 5. Close the finisher top cover. 6. Move the finisher back into position and connect it to the inverter..

  • Page 90

    C9650 user’s guide> 90 c heck i nverter , paper jam 1. Operate the finisher lever (1) and move the finisher away from the inverter. 2. Squeeze the recessed handle (2) and open the left side cover of the inverter. 1 2.

  • Page 91

    C9650 user’s guide> 91 3. Carefully remove any jammed paper. 4. Close the inverter left side cover. 5. Move the finisher back into position and connect it to the inverter..

  • Page 92

    C9650 user’s guide> 92 6. Operate the inverter lever (3) and separate the inverter from the printer. 7. Open the right side door (4) of the inverter. 3 4.

  • Page 93

    C9650 user’s guide> 93 8. Remove any jammed paper. 9. Close the right side door..

  • Page 94

    C9650 user’s guide> 94 10. Move the finisher and inverter back into position and connect to the printer. A voiding paper jams the following table summarizes possible causes of paper jams and suggests ways of avoiding them. Possible cause suggested remedy the printer is not level. Place the printer o...

  • Page 95

    C9650 user’s guide> 95 d ealing with unsatisfactory printing your printer feed roller is dirty. Wipe the roller with a cloth moistened with water. Your printer feed rollers are wearing out. Replace the feed rollers. The media weight or type have been wrongly set. Select the correct printer menu sett...

  • Page 96

    C9650 user’s guide> 96 printing is light. The toner cartridge is not properly seated. Reinstall the toner cartridge. The toner is low. Replace the toner cartridge. The paper is moist. Use paper stored in proper temperature and humidity conditions. The paper is not suitable for the printer. Use recom...

  • Page 97

    C9650 user’s guide> 97 s taple jams – f inisher ( optional accessory ) c heck f inisher , s taple j am when the display indicates a staple jam has occurred, clear the jam as follows: 1. Open the finisher front cover. White area of paper is lightly stained. Paper contains static. Use paper stored in ...

  • Page 98

    C9650 user’s guide> 98 2. Turn the knob in the direction indicated until the colored indicator appears. 3. Remove any paper that awaits stapling in the paper ejection area..

  • Page 99

    C9650 user’s guide> 99 4. Pull out the staple unit. 5. Turn the knob in the direction indicated to move the stapler to the front..

  • Page 100

    C9650 user’s guide> 100 6. Grip both sides of the staple cartridge, pull it up and remove it. 7. Raise the staple cartridge gate. 8. Remove all staples that are emerging from the staple case..

  • Page 101

    C9650 user’s guide> 101 9. Return the staple cartridge gate to its original position. 10. Replace the staple cartridge. 11. Ensure that the staple cartridge is securely installed back into the staple unit then push the staple unit fully home..

  • Page 102

    C9650 user’s guide> 102 12. Close the finisher front cover, being careful not to trap your fingers..

  • Page 103

    C9650 user’s guide> 103 s pecifications item specification dimensions 23.6x25x18.5in (wxdxh) 599x625x471mm (wxdxh) weight without options, approx. 167.5 lb (76 kg) print speeds 36 ppm color; 40 ppm monochrome 20 – 28 lb paper resolution 1200 x 600 dpi emulations pcl 5c, pcl xl 2.1, ps, ibm ppr, epso...

  • Page 104

    C9650 user’s guide> 104 noise level operating: 54dba maximum standby: 42dba maximum power save: 28dba maximum after 30 mins background level item specification.

  • Page 105: A – D

    C9650 user’s guide> 105 a ppendix a – d isplay p anel m essages the display panel messages are intended to be self-explanatory. Representative messages are given as examples below. Message comment ready to print your printer is online and ready to print. Printing tttttt your printer is printing and ...

  • Page 106

    C9650 user’s guide> 106 open cover paper remains tttttt please see help for details additional paper has been detected after a paper jam has been cleared. Open tttttt side cover to check for additional paper. You can access help details by pressing the help button. Check image drum cccccc please see...

  • Page 107: B – M

    C9650 user’s guide> 107 a ppendix b – m enu system the top-level functions menus are: > configuration > print information > print secure job > menus > admin setup > calibration > print statistics the two other special top-level menus are: > boot menu > system maintenance the following tables summari...

  • Page 108

    C9650 user’s guide> 108 c onfiguration p rint p age c ount f inisher c ount item value description total pages nnnnnn displays the total number of pages printed. Note: in duplex printing, each sheet is counted as 2 pages. Color page nnnnnn displays number of color printed pages converted to letter e...

  • Page 109

    C9650 user’s guide> 109 s upplies l ife n etwork item value description xxxx drum remaining nnn% displays the remaining life span of the xxxx drum as a percentage where xxxx can be cyan, magenta, yellow, black. Belt remaining nnn% displays the remaining life span of the belt unit as a percentage. Fu...

  • Page 110

    C9650 user’s guide> 110 p aper s ize in t ray s ystem item value description traym where m is in range 1 to 5 (similar arrangement for all trays) executive letter short edge letter long edge legal 14 legal 13.5 tabloid tabloid extra legal 13 a6 a5 a4 short edge a4 long edge a3 a3 nobi a3 wide b5 sho...

  • Page 111

    C9650 user’s guide> 111 c onfiguration example – monochrome pages printed to display the total monochrome pages printed so far (remembering that a duplex page counts as two pages): 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either th...

  • Page 112

    C9650 user’s guide> 112 p rint i nformation item item description configuration execute prints printer configuration details. Network execute prints summary information about the wired network. Demo page demo 1 execute prints a demo page. File list execute prints a list of jobs stored on the hard di...

  • Page 113

    C9650 user’s guide> 113 p rint i nformation example – demonstration page to print a printer demo page to demonstrate how your printer prints: 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either the up-arrow or down-arrow button and pre...

  • Page 114

    C9650 user’s guide> 114 p rint s ecure j ob item value description encrypted job enter password nnnn enter a password to use secure printing. Not found use to print an encrypted secure job that has been stored on the hdd. Not found: (no jobs) is indicated when there is no output file. The following ...

  • Page 115

    C9650 user’s guide> 115 m enus t ray c onfiguration item value description paper feed tray1 tray2 tray3 tray4 tray5 mp tray specifies a feed tray. Indicated only when tray2–5 implemented. Auto tray switch on off sets the automatic tray switch function. Tray sequence down up paper feed tray specifies...

  • Page 116

    C9650 user’s guide> 116 traym config, where m is in range 1 to 5 (similar arrangement for all trays) paper size tray size custom sets paper in traym. X dimension 3.9 – 8.3 (a) – 8.5 (l) – 12.9 inch 100 – 210 (a) – 216 (l) – 328 mm sets custom paper width for traym. Sets for the direction perpendicul...

  • Page 117

    C9650 user’s guide> 117 traym config, where m is in range 1 to 5 (similar arrangement for all trays) legal 14 paper legal 14 legal 13.5 sets the length of the legal paper in traym. Change this to legal 13.5 if that is the standard legal size in your country. Item value description.

  • Page 118

    C9650 user’s guide> 118 mp tray config paper size a3 nobi a3 wide a3 a4 sht edge a4 long edge (a) a5 a6 b4 b5 short edge b5 long edge legal 14 legal 13.5 tabloid extra tabloid letter sht edge letter long edge (l) executive custom com-9 envelope com-10 envelope monarch envelope dl envelope landscape ...

  • Page 119

    C9650 user’s guide> 119 mp tray config media type plain letterhead transparency labels bond recycled card stock rough glossy envelope user type1 user type2 user type3 user type4 user type5 user type 6 user type 7 user type 8 user type 9 user type 10 sets the media type for mp tray. Media weight auto...

  • Page 120

    C9650 user’s guide> 120 s ystem a djust item value description power save time 5 min 15 min 30 min 60 min 240 min sets the period after which power save mode starts. Clearable warning online job when online is selected, you must manually clear the warning by pressing the online button. Change to job...

  • Page 121

    C9650 user’s guide> 121 low toner continue stop sets the printing operation when insufficient toner is detected. Continue : the printer can continue printing while remaining online. Stop : the printer stops printing and goes offline. Jam recovery on off on : continues printing the job, including any...

  • Page 122

    C9650 user’s guide> 122 print position adjust duplex x adjust 0.00 +0.25 – +2.00 -2.00 – -0.25 mm 0.00 +0.01 – +0.08 -0.08 – -0.01in during the flip-side printing of duplex printing, adjusts the location of the whole printing image (0.25 mm, 0.01in interval) perpendicular to the direction of paper m...

  • Page 123

    C9650 user’s guide> 123 paper color setting 0 +1 +2 -2 -1 used for fine color adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on plain paper. Decrement setting when a white horizontal dotted line or a sno...

  • Page 124

    C9650 user’s guide> 124 m enus example 1 – t ray 1 transparencies to print on transparencies (accommodated in tray1): 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either the up-arrow or down-arrow button and press them repeatedly until...

  • Page 125

    C9650 user’s guide> 125 5. Press the enter button to select this item. 6. Press the up-arrow or down-arrow buttons repeatedly until tray1 config is highlighted. 7. Press the enter button to select this item. 8. Press the up-arrow or down-arrow buttons repeatedly until mediatype is highlighted. 9. Pr...

  • Page 126

    C9650 user’s guide> 126 10. Press the up-arrow or down-arrow buttons repeatedly to move through the range of paper sizes until the required size is highlighted. 11. Press the enter button to select this value. 12. Check that an asterisk (*) appears beside the chosen size. 13. Press the online button...