Oki MC770 series Setup Manual

Other manuals for MC770 series: User Manual, User Manual, User Manual, User Manual, Material Safety Data Sheet, User Manual, User Manual, Setup Manual, User Manual, Maintenance Manual, Maintenance Manual

Manual is about: Controller Unit

Page of 11

Download

Print this page

Bookmark us

1 / 11

GD-1340

GD-1340

for MC760/MC770/MC780/ES7460/ES7470/ES7480/MPS3537/MPS4242

SET-UP GUIDE

Warnings Points

• The unpacking and setup procedure shall be done by a qualified service technician.

• Be sure to unplug the power cable of the equipment before installing and setting up the product.

• Disconnect the ground wire after unplugging the power cable. In addition, be sure to connect the ground wire

before plugging the power cable.

Cautionary Points

• Install the equipment near an outlet. Be sure to wire the power cable securely so as to unplug it easily and not

to trip over it.

• According to the equipment model, these illustrations may differ.

• The covers of this equipment have been designed so as not to be easily removed. Therefore, when using

tools, be sure not to put your face and hands in the direction in which force will be applied; otherwise this could

result in injury. In addition, pay attention not to deform parts by using too much force.

• When unpacking and setting up the product, be sure to wear gloves to avoid injury.

Accessories

1 2 3 4 5 6 7 Next › »

Summary of MC770 series

Page 1
1 / 11 gd-1340 gd-1340 for mc760/mc770/mc780/es7460/es7470/es7480/mps3537/mps4242 set-up guide warnings points • the unpacking and setup procedure shall be done by a qualified service technician. • be sure to unplug the power cable of the equipment before installing and setting up the product. • dis...
Page 2
2 / 11 gd-1340 setup 1. Take out the fax unit and the accessories. 2. Take off the covers. • for jpd: 3 covers • other than jpd: 2 covers 3. Take off the cover. * you must wear gloves for this procedure. 1) remove [b] and [e]. • b: 1 • e: 1 2) open [f]. 3) push the locking button to open [g]. F g b ...
Page 3
3 / 11 gd-1340 4) remove [b]. 5) remove [e]. 6) open the covers in the order of (a) and (b). 7) close [g]. G b a b e.
Page 4
4 / 11 gd-1340 8) release the latches (a) of the cover. • a: 2 * as shown in the figure, insert a flathead screwdriver into the groove and push it in the direction of the arrow to release the latches. When using tools, be sure not to put your face and hands in the direction in which force will be ap...
Page 5
5 / 11 gd-1340 11) closer [f]. 12) take off the upper side of the cover, release the latch (e) and then take off the cover. • e: 1 place 4. Loosen the screws and take off the cover. • screws: 15 places e f.
Page 6
6 / 11 gd-1340 5. Connect the connectors of [d] and [b] to the board. 6. Place [a] into the attaching position and secure it with [a]. • a: 4 when installing [a], be careful not to catch the rear side cables. 7. Connect the cable of [a] to the board. D b a a a a a.
Page 7
7 / 11 gd-1340 8. Connect the connectors of [d] and [b] to [a]. 9. Attach the cover and tighten the screws. • screws: 15 places 10. Insert its latch (e) and then the parts indicated by the arrows as shown in the figure. Perform this operation with care to avoid injury. In addition, be sure not to da...
Page 8
8 / 11 gd-1340 12. Open [f]. 13. Insert the latch (d) of the cover. 14. Close the covers in the order of (a) and (b). 15. Push the locking button to open [g]. 16. Attach [b]. • b: 1 g b b a f d.
Page 9
9 / 11 gd-1340 17. Attach [b] and [e]. • b: 1 • e: 1 18. Attach [e]. • e: 1 19. Close in the order of [g] and [f]. 20. Connect [e]. 21. Connect the cable from the telephone. G f e b e e.
Page 10
10 / 11 gd-1340 22. Attach the label [h]. • h: 1 23. Select the corresponding label [j] according to the destination and applicable model and attach it. • j: 1 24. The operation is now completed. Setting destination 1. Destination (1) plug the power cable. (2) turn the power on by means of the main ...
Page 11
11 / 11 gd-1340 initializing memory 2. Memory initialization (1) press the [on/off] button while pressing [1] and [*]. (2) [100] → [start] button (3) when “are you sure?” appears, press the [initialize] button. (4) after the display has changed from “testmode 100” to “test mode cl”, shut down the eq...