1. DL manuals
  2. Oki
  3. Software
  4. ML520n
  5. User Manual

Oki ML520n User Manual

Manual is about: High Performance 10/100 Base-T Ethernet Network Print Server

Summary of ML520n

  • Page 1

    Okilan 6120e ® user’s guide high performance 10/100 base-t ethernet network print server.

  • Page 2

    Ii copyright and trademark information oki okilan 6120e user’s guide every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki data assumes no responsibility for the results of errors beyond its control. Oki data also cannot guarantee that ...

  • Page 3: Organization

    Iii organization and contents oki okilan 6120e user’s guide organization this manual has been divided into eight sections. Section i contains and installation instructions for the okilan 6120e print server. Section ii contains information about management features, an extremely valuable set of okila...

  • Page 4: Index

    Iv organization and contents oki okilan 6120e user’s guide section iv: tcp/ip .................................................. Iv-1 chapter 1: introduction ................................................ Iv-5 chapter 2: configuring the okilan 6120e ................ Iv-7 chapter 3: tcp/ip configur...

  • Page 5: Network Operating Systems

    V network operating systems oki okilan 6120e user’s guide network operating systems overview okilan 6120e simultaneously supports several network protocols in various combinations. Below is a list of supported network protocols accompanied with nos/os requirements. Tcp/ip and windows nt tcp/ip, ftp ...

  • Page 6: Service Information

    Vi technical support oki okilan 6120e user’s guide service information note: this information is valid for the united states and canada only. Oki data on line visit the oki data web site at http://www.Okidata.Com for the latest information on: • software drivers • product guides • customer support •...

  • Page 7: Oki Data Service Centers

    Vii technical support oki okilan 6120e user’s guide oki data customer support representatives agents are available 24 hours a day, 7 days a week at 1-800-oki-data (1-800-654-3282). Please be sure that you are calling from a telephone close to your printer, so you can describe your problem accurately...

  • Page 8: United States

    Viii technical support oki okilan 6120e user’s guide united states oki data americas, inc. 2020 bishops gate blvd. Mt. Laurel, nj 08054 tel: 1-800-654-3282 fax: 1-856-222-5247 canada oki data americas, inc. 2735 matheson blvd. East, unit 1 mississauga, ontario, canada l4w 4m8 tel: 1-800-654-3282 fax...

  • Page 9

    Ix technical support oki okilan 6120e user’s guide when you call technical support, the following information will help us answer your questions more quickly and accurately. Please be able to identify the following: • okilan model number • serial number • configuration sheet settings • type of netwo...

  • Page 10

    X technical support oki okilan 6120e user’s guide.

  • Page 11: Section I:

    Hardware installation section i: hardware installation.

  • Page 12

    I - 2 section i - hardware installation oki okilan 6120e user’s guide.

  • Page 13: Contents

    Hardware installation i - 3 section i - hardware installation oki okilan 6120e user’s guide contents powering on the okilan 6120e ............................. I-7 printing a configuration sheet ............................... I-8.

  • Page 14

    I - 4 section i - hardware installation oki okilan 6120e user’s guide.

  • Page 15: Removing The Okilan 6120E

    Hardware installation i - 5 section i - hardware installation oki okilan 6120e user’s guide the okilan 6120e print server enables ethernet network users to connect to a printer with an oki sidm port. The okilan 6120e supports 10/100-megabit networks and most popular network operating systems and sid...

  • Page 16

    I - 6 section i - hardware installation oki okilan 6120e user’s guide 4. Unplug the power adapter from the wall outlet. Then unplug the power adapter wire from the power jack on the okilan 6120e. 5. Slide the okilan 6120e out of the printer and store it in a safe place for future network requirement...

  • Page 17

    Hardware installation i - 7 section i - hardware installation oki okilan 6120e user’s guide re-installing the okilan 6120e to use your printer on a network, you must re-install the okilan 6120e. 1. Turn off printer power. 2. Unplug the power cord. 3. Detach the interface cable from the rear of the p...

  • Page 18

    I - 8 section i - hardware installation oki okilan 6120e user’s guide 5. Plug the power adapter wire into the power jack on the okilan 6120e. Then plug the power adapter into a 120 vac wall outlet. Please note that some countries may require a different adapter for local voltages, such as 240 vac. 6...

  • Page 19: Powering On The Okilan 6120E

    Hardware installation i - 9 section i - hardware installation oki okilan 6120e user’s guide powering on the okilan 6120e turn printer power on. The red and green indicators on the okilan 6120e will blink during self-test. When self-test completes successfully, the red indicator will go off and the g...

  • Page 20

    I - 10 section i - hardware installation oki okilan 6120e user’s guide note: if the red and green indicators do not display as indicated above, see hardware troubleshooting at the end of this section. Printing a configuration sheet to print configuration information, press the test button on the fro...

  • Page 21: Installing The Okilan 6120E

    Hardware installation i - 11 section i - hardware installation oki okilan 6120e user’s guide installing the okilan 6120e software utilities introduction your okilan 6120e print server comes with two types of software utilities: okiview 32 and okinet utilities. Okiview 32 okiview 32 is a general purp...

  • Page 22: Software In Windows

    I - 12 section i - hardware installation oki okilan 6120e user’s guide installing the okinet utilities software in windows 1. Click the okinet utilities button on the oki menu installer screen. 2. When the setup screen appears, select the utility group for the network environment you have, then clic...

  • Page 23: Windows Utility Groups:

    Hardware installation i - 13 section i - hardware installation oki okilan 6120e user’s guide windows utility groups: netware management utilities okinet utility for netware okinet utility for nds (workstation and server) okinet utility for nds (workstation) okinet connect windows printing okinet con...

  • Page 24: Okinet For The Apple

    I - 14 section i - hardware installation oki okilan 6120e user’s guide okinet for the apple ® macintosh ® utility note: the okilan utilities cd is designed for more than one type of okilan print server and includes features that do not apply to the okilan 6120e. Specifi- cally, apple ethertalk is su...

  • Page 25: Solution

    Hardware installation i - 15 section i - hardware installation oki okilan 6120e user’s guide solution a) unplug the okilan 6120e power adapter from the wall outlet. Remove the network cable. Plug the network cable back in until you hear a positive click. Check the other end of the cable in the same ...

  • Page 26: Led Display

    I - 16 section i - hardware installation oki okilan 6120e user’s guide led display green indicator is flashing slowly (1 timer/sec); the okilan 6120e is trying to print a job. Problem the printer is malfunctioning or does not have sufficient paper or toner. Solution verify that the printer is not sh...

  • Page 27: Led Display

    Hardware installation i - 17 section i - hardware installation oki okilan 6120e user’s guide led display the red and green indicators are alternately flashing for longer than two minutes. Problem the okilan 6120e is in firmware download mode. This means it is waiting for new firmware to be sent befo...

  • Page 28

    I - 18 section i - hardware installation oki okilan 6120e user’s guide.

  • Page 29: Section Ii:

    Advanced management section ii: advanced management features.

  • Page 30: In This Section

    Ii - 2 section 2 - advanced management features oki okilan 6120e user’s guide in this section chapter 1 snmp ...................................................... Ii-3 overview ....................................................... Ii-3 private mib ....................................................

  • Page 31: Chapter 1

    Ii - 3 section 2 - chapter 1 - snmp oki okilan 6120e user’s guide advanced management chapter 1 simple network management protocol (snmp) overview simple network management protocol (snmp) provides network administrators with the ability to communicate management functions between an snmp manager an...

  • Page 32: Traps

    Ii - 4 section 2 - chapter 1 - snmp oki okilan 6120e user’s guide note: if you attempt a reset while a job is printing, the job may not print successfully. Certain variables are critical, that is, they change a fundamental operating parameter of the okilan 6120e. These variables are saved by the oki...

  • Page 33: Security

    Ii - 5 section 2 - chapter 1 - snmp oki okilan 6120e user’s guide advanced management in order to receive okinet alert traps, the okilan 6120e must have bi-directional status enabled (it is disabled by default). Extended status can be enabled through the okilan 6120e configuration utility (telnet) f...

  • Page 34: Chapter 2

    Ii - 6 section 2 - chapter 2 - hp jetadmin support oki okilan 6120e user’s guide chapter 2 hp jetadmin support overview this section contains instructions and information on how to configure and obtain diagnostic information from your okilan 6120e using the hewlett-packard jetadmin software. Softwar...

  • Page 35: Ok.

    Ii - 7 section 2 - chapter 2 - hp jetadmin support oki okilan 6120e user’s guide advanced management 7. Select the desired queues from the list of available queues to be added into service. Click the service button to move the selection to the serviced queues column. When all queues have been added,...

  • Page 36: Chapter 3

    Ii - 8 section 2 - chapter 3 - hp web jetadmin support oki okilan 6120e user’s guide chapter 3 hp web jetadmin support overview this section contains instructions and information on how to configure, install, and obtain diagnostic information from your okilan 6120e using the hewlett-packard web jeta...

  • Page 37: The Continue Button.

    Ii - 9 section 2 - chapter 3 - hp web jetadmin support oki okilan 6120e user’s guide advanced management 4. On the install printer page 1 page, select an nt domain from the pull-down menu. Enter the user name and password of a domain user with sufficient rights to create a printer and click the cont...

  • Page 38: Chapter 4

    Ii - 10 section 2 - chapter 4 - okilan 6120e web configuration oki okilan 6120e user’s guide chapter 4 okilan 6120e web configuration overview this section contains instructions and information on how to configure and manage your okilan 6120e using a standard web browser. Software requirements tcp/i...

  • Page 39

    Ii - 11 section 2 - chapter 4 - okilan 6120e web configuration oki okilan 6120e user’s guide advanced management note: as a layer of security, the tcp port number that the device uses to communicate with browsers, called the http port, can be modified from a default of 80. If the port is modified, t...

  • Page 40: Configuration

    Ii - 12 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide configuration 1. Select the login as admin link under the configuration menu. 2. On the enter network password screen, enter the user name and password. The default administrator user name is admin. The defa...

  • Page 41

    Ii - 13 section 2 - chapter 4 - okilan 6120e web configuration oki okilan 6120e user’s guide advanced management 5. A request results page will appear indicating one of the following: • configuration successfully set: the values have been successfully saved to the print server. Go to another page to...

  • Page 42: Interface:

    Ii - 14 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide * the following values are currently only configurable through the web browser interface: web admin configuration under the configuration menu, select the admin(web) link. • admin name - the name used to acc...

  • Page 43: Status

    Ii - 15 section 2 - chapter 4 - okilan 6120e web configuration oki okilan 6120e user’s guide advanced management status the home page for the print server shows general status information including the status of all printers currently attached. For more detailed status information, select the view c...

  • Page 44: Reset

    Ii - 16 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide reset reset reset the print server by selecting the reset link under the reset menu. A message will appear asking you to confirm the reset. Restore select restore defaults under the reset menu to restore sel...

  • Page 45: Troubleshooting

    Ii - 17 section 2 - chapter 4 - okilan 6120e web configuration oki okilan 6120e user’s guide advanced management troubleshooting server connection • the print server only supports two simultaneous http connections. If your browser fails to connect to the print server, the browser may be trying to op...

  • Page 46: Chapter 5

    Ii - 18 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide chapter 5 additional management features okinet alert oki okinet alert enterprise management utility allows administrators to proactively manage printers by being immediately alerted to printing problems bef...

  • Page 47: Okinet For Nds

    Ii - 19 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide advanced management okinet for nds okinet for nds allows administrators to create and manage oki print server objects in the nds tree. Okinet for nds integrates into novell’s netware administrator, netwaread...

  • Page 48

    Ii - 20 section 2 - chapter 5 - additional management features oki okilan 6120e user’s guide.

  • Page 49: Section Iii:

    Netw are section iii: netware.

  • Page 50: In This Section

    Iii - 2 section 3 - netware oki okilan 6120e user’s guide in this section chapter 1 introduction ........................................... Iii-4 overview ...................................................... Iii-4 before you start ........................................... Iii-4 selecting pserve...

  • Page 51

    Iii - 3 section 3 - netware oki okilan 6120e user’s guide netw are chapter 3 okinet for nds .................................... Iii-24 overview .................................................... Iii-24 installing okinet for nds for novell netware 4.1 .................................................

  • Page 52: Chapter 1: Introduction

    Iii - 4 section 3 - chapter 1 - introduction oki okilan 6120e user’s guide chapter 1: introduction overview this section contains instructions and information on how to configure your okilan 6120e in the netware environment. There are three environments in which to configure the okilan 6120e: • bind...

  • Page 53: Selecting Pserver Or

    Iii - 5 section 3 - chapter 1 - introduction oki okilan 6120e user’s guide netw are selecting pserver or rprinter/nprinter mode your okilan 6120e supports both pserver and nprinter mode. There are several factors to consider when choosing which mode to use. In pserver mode, the okilan 6120e operates...

  • Page 54: Chapter 2

    Iii - 6 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide chapter 2 okinet for netware overview this chapter contains information about how to configure the okilan 6120e in bindery and nds environments using the okinet for netware utility. Note: okinet for netware contains min...

  • Page 55: Running Okinet For Netware

    Iii - 7 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are running okinet for netware to run the utility, double-click on the okinet icon. The main okinet for netware screen will display. By default, the all print servers view is selected and all print servers attached...

  • Page 56

    Iii - 8 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netware configuration options to configure options specific to the netware protocol, select the netware file tab. The following screen will display: pserver or rprinter mode several factors should be considered when cho...

  • Page 57: Netware Queues Configuration

    Iii - 9 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are nds settings nds settings need to first be created and setup using the nwadmin or pconsole utility. Create an nds print server object. Then, create one nds printer object per output port. For example, printer 1...

  • Page 58: Port File Tab.

    Iii - 10 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netware queue load balancing print jobs can be distributed to multiple printers on selected queues by selecting the same queue multiple times and selecting a different output port for each queue entry. Netware port con...

  • Page 59

    Iii - 11 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are ethertalk configuration options to modify configuration settings specific to the ethertalk protocol such as the name and zone. For specific information on other ethertalk options, see section vii, ethertalk, o...

  • Page 60

    Iii - 12 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide • postscript - inserts the appropriate character string in front of each print job to switch the printer to the postscript printer language. • automatic - enables the auto language sensing function. This function exami...

  • Page 61: - Compatibility (No Bidi)

    Iii - 13 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are bi-directional printer status support enable this option for enhanced status from bi-directional printers that support pjl. Output type select the desired level of support for 1284 communications. The followin...

  • Page 62

    Iii - 14 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide fill in the following information: system name enter the name of your choice. This name will identify the okilan 6120e in your snmp-based management program. System contact enter any information useful to a user if pro...

  • Page 63: Snmp Traps Configuration

    Iii - 15 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are trap community name enter the community name which will be used when traps are sent from the okilan 6120e. This setting allows trap utilities to only accept traps from devices with appropriate community names....

  • Page 64: Saving The Configuration

    Iii - 16 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide trap destination • netware protocol - enter the network number and hardware address, respectively, to which traps will be sent. To broadcast traps to all addresses on all networks, enter ffffffff (8 characters) in the ...

  • Page 65: Enabling/disabling Protocols

    Iii - 17 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are enabling/disabling protocols to enable or disable protocols on the okilan 6120e, select the protocols file tab. Select each protocol you wish to enable. If you disable a protocol, the okilan 6120e will no long...

  • Page 66

    Iii - 18 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide caution: make sure there are no print jobs active when you reset the okilan 6120e. All protocols will be restarted. If you attempt a reset while a job is printing, the job may not print successfully. Restoring factory ...

  • Page 67: Not Print Successfully.

    Iii - 19 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are caution: make sure there are no active print jobs when you select restore factory defaults. If you reset the okilan 6120e while a job is printing, the job may not print successfully. Creating customized views ...

  • Page 68: Modifying View Settings

    Iii - 20 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide modifying view settings before modifying the settings, select the name of the view you wish to edit from the name field. Display filter the filter option displays only those print servers matching specific criteria. Th...

  • Page 69: 3. Select Add.

    Iii - 21 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are • specify devices/networks - this method adds specific print servers (or groups of print servers) to the list. This can be useful when only a subset of the list of okilan 6120e products is desired. To select a...

  • Page 70: Information

    Iii - 22 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide refresh the refresh rate defines how often the okinet for netware utility updates the main print server list. To define a refresh rate, select the automatic refresh box and then enter the refresh rate in the field prov...

  • Page 71

    Iii - 23 section 3 - chapter 2 - okinet for netware oki okilan 6120e user’s guide netw are set community name enter the set community name necessary to access the okilan 6120e or group of okilan 6120e products selected. Add select the add button to define access to a new okilan 6120e or a group of o...

  • Page 72: Chapter 3

    Iii - 24 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide chapter 3 okinet for nds overview okinet for nds is a dynamic link library (dll) which allows users to create and manage oki print server objects in the nds tree. Okinet for nds integrates into novell’s netware administrat...

  • Page 73: Novell Netware 4.1

    Iii - 25 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide netw are refer to the following table to determine which method to use to install okinet for nds: netware version client operating system windows 3.X windows 95/98 windows nt/2000 netware 4.1 see installing okinet for nds ...

  • Page 74: Windows 3.X

    Iii - 26 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide installing okinet for nds for novell netware 4.X, netware 5.X, and windows 3.X okinet for nds must be installed in the same location you have installed netware administrator. This may be located on the file server or on an...

  • Page 75: Netware 4.X, Netware 5.X,

    Iii - 27 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide netw are installing okinet for nds for novell netware 4.X, netware 5.X, windows 95/98 and windows nt/2000 okinet for nds must be installed in the same location you have installed netware administrator. This may be located ...

  • Page 76: 4. Click Ok.

    Iii - 28 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide creating a new okilan 6120e object to create a new okilan 6120e object from novell’s netware administrator, perform the following steps: 1. Select the container (also known as organizational unit) in which you want the obj...

  • Page 77: 9. Select Create.

    Iii - 29 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide netw are 7. From the list of oki devices, select a device to assign to the object. 8. Enter a name for the new oki print server object. 9. Select create. The new oki print server object should now appear in the directory t...

  • Page 78: Page, Then Select Assign.

    Iii - 30 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide note: to load balance print queue jobs, repeat steps 5 through 9 for another port. Create a new printer object for the okilan 6120e port and then select the same print queue object. This will allow multiple printers to ser...

  • Page 79: Okinet For Nds

    Iii - 31 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide netw are configuring the okilan 6120e using okinet for nds the following steps outline how to configure an okilan 6120e. 1. From the nwadmin screen, select (double-click) the okilan 6120e you wish to configure. 2. Set the ...

  • Page 80

    Iii - 32 section 3 - chapter 3 - okinet for nds oki okilan 6120e user’s guide the install utility on the installation diskette can also be used to remove the oki print server class. This utility removes the class from novell’s netware administrator and removes all the associated files that were copi...

  • Page 81: Chapter 4

    Iii - 33 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are chapter 4 using the okilan 6120e in ndps (netware 4.X , 5.1 or higher) introduction novell â distributed print servicesä (ndps â ) is novell’s new printing architecture for use with netware version...

  • Page 82

    Iii - 34 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide 6. To add a driver to the list, click add to display the add resources dialog box. 7. Click browse to display the select printer driver dialog box. Locate the appropriate printer driver .Inf file. 8. Select...

  • Page 83: Nwadmin32

    Iii - 35 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are setting up the okilan 6120e through nwadmin32 there are two types of printers available with ndps. One is public access, which anyone on the tree can get to. The other is private access, which requ...

  • Page 84

    Iii - 36 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide private access printers: these can only be created through nwadmin32 1. Create ndps manager in nwadmin32. 2. Go to the context in which the private printer is to reside. 3. Select create. The new object scr...

  • Page 85

    Iii - 37 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are setting up the okilan 6120e for public access printers at the file server console 1. Create ndps manager in nwadmin32. 2. Load the ndps manager on the file server. 3. Select insert new printer agen...

  • Page 86: Or Higher In Tcp/ip

    Iii - 38 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide setting up the okilan 6120e in netware 5.1x or higher in tcp/ip there is an accelerated procedure for setting up the okilan 6120e in netware 5.1x or higher in tcp/ip that is similar to the procedure for net...

  • Page 87

    Iii - 39 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are the buttons on the oki printer control screen provide the following functions: · identification ¾ gives you access to the location and description of the printer. · features ¾ displays specific fea...

  • Page 88

    Iii - 40 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide oki data okilan 6000 series – ip address configuration wizard loading the ip address configuration wizard 1. To load the ip address configuration wizard, press okinet utilities in the printer cd-rom network...

  • Page 89

    Iii - 41 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are 3. Select novell distributed print services snapin and browse to the directory of netware administrator. Click install. Setting up the okilan 6120e for public access printers once the ndps printer ...

  • Page 90

    Iii - 42 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide 6. Click ok. The following screen appears: 7. Click next. 8. Enter the printer’s ip address as shown on the okilan 6120e configuration sheet and click finish. 9. If the “waiting for printer agent to load” s...

  • Page 91

    Iii - 43 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are 11.The select printer driver screen appears. Choose your operating system and select okidata ml 320 tn. 12.Click continue. A screen displaying the drivers that you have selected appears. 13.Click o...

  • Page 92

    Iii - 44 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide 6. Select okidata okilan 6000 series configuration as the gateway type. 7. Click ok. The following screen appears: 8. Click next..

  • Page 93

    Iii - 45 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide netw are 9. Enter the printer’s ip address as shown on the okilan 6120e configuration sheet and click finish. 10.If the “waiting for printer agent to load” screen stays on for more than 60 seconds, click “s...

  • Page 94

    Iii - 46 section 3 - chapter 4 - using the okilan 6120e in ndps oki okilan 6120e user’s guide.

  • Page 95: Section Iv:

    Tcp/ip section iv: tcp/ip.

  • Page 96: In This Section

    Iv - 2 section 4 - tcp/ip oki okilan 6120e user’s guide in this section chapter 1introduction ........................................... Iv-5 overview ................................................................................... Iv-5 software requirements ........................................

  • Page 97

    Iv - 3 section 4 - tcp/ip oki okilan 6120e user’s guide tcp/ip saving the configuration ........................................................ Iv-34 displaying okilan 6120e diagnostic information ............... Iv-34 printing a configuration sheet ................................................ ...

  • Page 98

    Iv - 4 section 4 - tcp/ip oki okilan 6120e user’s guide configuring sco unix for printing with the okilan 6120e ................................................... Iv-73 ibm’s aix ver. 3.X for printing with the okilan 6120e ................................................... Iv-75 configuring solari...

  • Page 99: Chapter 1

    Iv - 5 section 4 - chapter 1 - introduction oki okilan 6120e user’s guide tcp/ip chapter 1 introduction overview this section contains instructions and information on how to configure your okilan 6120e. You will also be instructed on how to set up your host computers to print to the okilan 6120e usi...

  • Page 100: Network Preparation

    Iv - 6 section 4 - chapter 1 - introduction oki okilan 6120e user’s guide network preparation • you should be familiar with network administration as well as the physical setup and operation of your network. • advise users of possible disruption during installation. • make sure the serial number and...

  • Page 101: Chapter 2

    Iv - 7 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide tcp/ip chapter 2 configuring the okilan 6120e choosing an ip address every tcp/ip network device is required to have a unique ip address. The ip address can be permanently stored using one of the following: • o...

  • Page 102: Configuring The Okilan 6120E

    Iv - 8 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide configuring the okilan 6120e there are four utilities available to configure the okilan 6120e for tcp/ip printing. You may use whichever utility is best suited for your needs. • okinet for tcp/ip - windows tcp/...

  • Page 103

    Iv - 9 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide tcp/ip gleaning if an ip address has not been permanently assigned when the okilan 6120e is powered on or reset, it will look for a ping packet on the network. If the okilan 6120e receives a ping packet within ...

  • Page 104

    Iv - 10 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide dhcp the dynamic host configuration protocol (dhcp) provides a framework for passing configuration information to hosts on a tcp/ip network in a client/ server fashion. Dhcp is based on the bootstrap protocol ...

  • Page 105: Workstation” 0

    Iv - 11 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide tcp/ip static route entry when the okilan 6120e is powered on or reset and no permanent ip address has been assigned, it will attempt to obtain an ip address through gleaning, rarp, bootp or dhcp. If the okila...

  • Page 106: Other Utilities

    Iv - 12 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide most unix operating systems support either the rarp or bootp protocol. To find out which protocol your operating system supports, request the manual page for the protocol’s daemon (e.G. Man bootpd or man rarpd...

  • Page 107

    Iv - 13 section 4 - chapter 2 - configuring the okilan 6120e oki okilan 6120e user’s guide tcp/ip verifying access to the okilan 6120e use the ping utility to verify access to the okilan 6120e. Ping ip address of okilan 6120e> if the okilan 6120e does not respond, your network or the device is not c...

  • Page 108: Chapter 3

    Iv - 14 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide chapter 3 tcp/ip configuration and printing overview the okilan 6120e supports printing from computers using tcp/ip and any of the following printing protocols: • line printer redirect/line printer daemon...

  • Page 109: Printing

    Iv - 15 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide tcp/ip configuring for tcp/ip network printing most computers that support tcp/ip network printing use the remote line printer daemon (lpd) protocol. This protocol was originally part of the berkeley soft...

  • Page 110

    Iv - 16 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide the okilan 6120e will parse the remote queue name and search for certain characters at the end which tell how to convert an ascii print job. The print server uses ff, lf and nf as ascii conversion specifi...

  • Page 111

    Iv - 17 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide tcp/ip configuring a bsd-style print queue for remote bsd-style lpd printing, add the okilan 6120e as a remote printer in the “/etc/printcap” database to each host printing to the okilan 6120e. You can ad...

  • Page 112: Remote Lpd Printing

    Iv - 18 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide log_file_name this is the path to a file where error information from the lpd will be logged. Example: if you are printing to an ascii printer that requires a carriage return/line feed, you may need two s...

  • Page 113: Ftp Printing

    Iv - 19 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide tcp/ip note: the remote lpd implementation of the okilan 6120e does not support any unix lpd input or output filters or the direct printing of banner pages. It is possible to configure some unix systems s...

  • Page 114: Type

    Iv - 20 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide type changes the representation type used for data transfer. Image (or binary) and ascii are the only types supported. Ascii equivalent to “type ascii.” binary equivalent to “type binary.” image equivalen...

  • Page 115: Timeout Checking

    Iv - 21 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide tcp/ip example: the following example prints a postscript file called chart.Ps to the okilan 6120e printer port 1 using ftp. $ ftp okilan 6120e_name connected to okilan 6120e_name. 220 esi-2810 version 3....

  • Page 116: Raw Port Printing

    Iv - 22 section 4 - chapter 3 - tcp/ip configuration and printing oki okilan 6120e user’s guide raw port printing host computer software can use a raw tcp/ip port connection to send data to the okilan 6120e. A tcp/ ip port has been assigned to the output port of the okilan 6120e as follows: tcp/ip p...

  • Page 117: Chapter 4

    Iv - 23 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip chapter 4 okinet for tcp/ip overview this section contains information about okinet for tcp/ip. Okinet for tcp/ip provides snmp-based support for the entire okilan 6120e family of print servers. Okinet for tcp/ip ...

  • Page 118: Running Okinet For Tcp/ip

    Iv - 24 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide running okinet for tcp/ip to run the utility, double-click on the okinet icon. The main okinet for tcp/ip screen will display. By default, the all print servers view is selected and all print servers attached to the subn...

  • Page 119: Configuring Tcp/ip Options

    Iv - 25 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip configuring tcp/ip options to configure options specific to the tcp/ip protocol, select the tcp/ip tab. The following screen will display: fill in the following information: ip address resolution • set permanent -...

  • Page 120: Networks.

    Iv - 26 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide subnet mask if your network environment includes subnets, you will want to set the subnet mask. The subnet mask must follow the format xxx.Xxx.Xxx.Xxx, where each xxx is a number from 0 to 255. The default subnet mask is...

  • Page 121: Netware and Netware Port

    Iv - 27 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip telnet/http password: allows you to modify the current password required for telnet or http access the default password is the serial number of the okilan 6020e. Netware and netware port configuration options for ...

  • Page 122

    Iv - 28 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide ethertalk configuration options to modify the configuration settings specific to the ethertalk protocol such as the name and zone. For specific information on ethertalk options, see section vi, ethertalk, or select the h...

  • Page 123

    Iv - 29 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip • off - print data stream will be sent directly to the output port without alteration. • pcl - inserts the appropriate character string in front of each print job to switch the printer to the pcl print language. •...

  • Page 124: Snmp Configuration Options

    Iv - 30 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide output type select the appropriate baud rate. Bidirectional printer status support enable this option for enhanced status from the bidirectional printer. Snmp configuration options snmp options specify which information ...

  • Page 125

    Iv - 31 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip system contact enter any information useful to a user if problems with the okilan 6120e arise. System location enter a description of the okilan 6120e location. Get community name this field is used to set the com...

  • Page 126: Enabling/disabling Protocols

    Iv - 32 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide enabling/disabling protocols to enable or disable protocols on the okilan 6120e, select the protocols tab. Select each protocol you wish to enable. If you disable a protocol, the okilan 6120e will no longer communicate u...

  • Page 127

    Iv - 33 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip trap destination • tcp/ip protocol - enter the ip address to which traps will be sent. The ip address must follow the format xxx.Xxx.Xxx.Xxx, where each xxx is a number from 0 to 255. To broadcast traps to all hos...

  • Page 128: Saving The Configuration

    Iv - 34 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide saving the configuration once all settings have been defined, select ok. The settings will be saved and you will be returned to the main okinet for tcp/ip screen. Displaying okilan 6120e diagnostic information to view ok...

  • Page 129: Select Reset.

    Iv - 35 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip restoring factory default settings to restore the okilan 6120e to factory default settings, select the okilan 6120e from the list of available print servers. From the print server menu bar, select reset. From the ...

  • Page 130: Creating Customized Views

    Iv - 36 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide creating customized views okinet for tcp/ip allows users to create multiple customized views for the list of okilan 6120e products. By creating different views, the user can narrow the information displayed to that which...

  • Page 131: Modifying View Settings

    Iv - 37 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip modifying view settings before modifying the settings, select the name of the view you wish to edit from the name field. Sort the sort option displays the okilan 6120e list in a specific order. The list can also b...

  • Page 132

    Iv - 38 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide search filter the search option defines the criteria for identifying okilan 6120e products on the network. • search local network - this method broadcasts a discovery request to locate all okilan 6120e print servers on t...

  • Page 133: 3. Select Add.

    Iv - 39 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip for example, if you currently have three columns displayed and you wish to add a fourth column to the far left of the screen, follow these steps: 1. Select the first column in the columns displayed field. 2. Selec...

  • Page 134

    Iv - 40 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide to configure okinet for tcp/ip to use the correct community names, select special options from the file menu. Ip address this field displays the address of each okilan 6120e for which okinet for tcp/ip has defined access...

  • Page 135: Number

    Iv - 41 section 4 - chapter 4 - okinet for tcp/ip oki okilan 6120e user’s guide tcp/ip configuring the discovery udp port number in order to discover okilan 6120e print servers on the network, okinet for tcp/ip communicates with the okilan 6120e print servers on a udp port number. Normally, using th...

  • Page 136: Chapter 5

    Iv - 42 section 4 - chapter 5 - web configuration oki okilan 6120e user’s guide chapter 5 web configuration if the dhcp protocol is enabled as a default, the print server may be accessed through an ordinary internet web browser, such as netscape navigator or microsoft internet explorer. See section ...

  • Page 137: Chapter 6

    Iv - 43 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide tcp/ip chapter 6 telnet configuration overview the okilan 6120e configuration utility (telnet) provides system, network and printer status information and allows you to change the configuration of your okilan 6120e. N...

  • Page 138

    Iv - 44 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide ***************************************** okilan 6120e configuration utility 1. Show network/printer information 2. Change password 3. Specify print server ip address 4. Specify subnet mask for your network 5. Identif...

  • Page 139

    Iv - 45 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide tcp/ip specify print server ip address (option 3) this option allows you to select the method the okilan 6120e uses to obtain its ip address or to set a permanent ip address. If the okilan 6120e has been configured to...

  • Page 140

    Iv - 46 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide note: if you select an invalid subnet mask you may not be able to access the okilan 6120e. Use this option with care! Identify default gateway ip address (option 5) if your local network is attached to other networks,...

  • Page 141

    Iv - 47 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide tcp/ip configure printer type this option enables you to indicate the printer type to which the okilan 6120e is connected. Printer choices are: 1. Oki data printer. 2. Custom printer. • language switching sequence - i...

  • Page 142: Not Print Successfully.

    Iv - 48 section 4 - chapter 6 - telnet configuration oki okilan 6120e user’s guide restore to factory default configuration (option 9) this option automatically restores the okilan 6120e to its original factory defaults. Be aware that when you restore the okilan 6120e to the original factory default...

  • Page 143: Appendix A

    Iv - 49 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide tcp/ip appendix a troubleshooting main status indicator upon power-up, the main status indicator flashes orange. It changes to green when the okilan 6120e passes self-test. The indicator stays orange if the okilan 6120e f...

  • Page 144

    Iv - 50 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide unable to assign ip address gleaning if you ping the device and are not getting a response, the glean is not working. Check the following possible problems: • verify the arp table contains the correct hardware and ip addr...

  • Page 145

    Iv - 51 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide tcp/ip unix bootp if you are running unix, try the following methods with the bootp server (check the documentation for your particular unix flavor). • verify the bootp server has reread the “/etc/ bootptab” file when the...

  • Page 146

    Iv - 52 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide static route entry if the okilan 6120e has printed a configuration page showing the default address, but it cannot be reached through telnet, check the following: • display the host’s routing tables with the ‘netstat - r’...

  • Page 147: Hardware Error Messages

    Iv - 53 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide tcp/ip okinet for tcp/ip - winsock errors • if you see an error before okinet for tcp/ip appears on the screen, try setting a host name in the host’s file in the windows directory (check the documentation for your windows...

  • Page 148: Unable to Print

    Iv - 54 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide printing a configuration page if the status indicator turns solid orange due to an error and no configuration page is printed, your printer may be configured for postscript operation. If so, you must re-configure your pri...

  • Page 149

    Iv - 55 section 4 - appendix a - troubleshooting oki okilan 6120e user’s guide tcp/ip • if the ftp succeeds, there is a problem with the lpr/ lp setup. Verify the hostname or ip address is correctly set for the queue. Try doing an lpstat (system v) or lpq (bsd) to query the status of the okilan 6120...

  • Page 150: Appendix B

    Iv - 56 section 4 - appendix b - application considerations oki okilan 6120e user’s guide appendix b application considerations overview this appendix provides application notes for the following: • assigning the okilan 6120e ip address with bootp • assigning the okilan 6120e ip address with rarp • ...

  • Page 151: Address With Bootp

    Iv - 57 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip assigning the okilan 6120e ip address with bootp bootp is an acronym for boot strap p rotocol. Every tcp/ip network device is required to have a unique 32-bit ip address assigned to it. Tcp/ip network de...

  • Page 152

    Iv - 58 section 4 - appendix b - application considerations oki okilan 6120e user’s guide a name can be arbitrarily assigned to any device on a network. The following examples use the name okiprinter. Remember that this name is arbitrary; a customer can assign any name they wish. /etc/bootptab: the ...

  • Page 153

    Iv - 59 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip 4. The bootpd daemon transmits a response to the okilan 6120e with the ip address 192.168.42.55. The okilan 6120e will use this ip address for all subsequent transmissions. For these steps to work proper...

  • Page 154: Address With Rarp

    Iv - 60 section 4 - appendix b - application considerations oki okilan 6120e user’s guide configuring the okilan 6120e ip address with rarp rarp is an acronym for r everse a ddress r esolution p rotocol. Every tcp/ip network device must have a unique 32-bit ip address. Tcp/ip network devices will ha...

  • Page 155

    Iv - 61 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip configuration files the purpose of rarp is to look up a 32-bit ip address given a 48-bit network hardware address. The rarp server (which is usually a unix workstation running a rarpd daemon) performs th...

  • Page 156

    Iv - 62 section 4 - appendix b - application considerations oki okilan 6120e user’s guide 4. The rarpd then consults the “/etc/hosts” file and looks up the name okiprinter. It finds an ip address (in this case 192.168.42.55) associated with the name okiprinter. 5. The rarpd daemon transmits a respon...

  • Page 157: With The Okilan 6120E

    Iv - 63 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip configuring hp-ux v8.07 for printing with the okilan 6120e this application note describes the configuration of the printing system on the hp-ux ver. 8.07 of the unix operating system. For clarity and br...

  • Page 159: A) Printer Name - Lj4

    Iv - 65 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip 3. Select the following options, in order, from the sam menu: peripheral devices -> printers and plotters -> actions -> add a remote printer (do not select add a network printer) a form appears asking yo...

  • Page 160: 7. Printer Name: — Lj4

    Iv - 66 section 4 - appendix b - application considerations oki okilan 6120e user’s guide 6. Enable the printer you just created using sam. Peripheral devices -> printers and plotters -> enable a printer ... 7. Printer name: — lj4 8. Start the lp request scheduler by typing: /usr/lib/lpsched 9. Run ...

  • Page 161: Kill -15 Process_Number.

    Iv - 67 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip prerequisites before you proceed, the following prerequisites must be met. Most of the time steps 2 through 5 are already configured since the hp-ux system is on a tcp/ip network. Do not perform steps 2 ...

  • Page 162: A) Printer Name - Lj4

    Iv - 68 section 4 - appendix b - application considerations oki okilan 6120e user’s guide procedure hp-ux uses an interactive utility called sam (system administration manager) to configure printing. 1. Login to the hp-ux system as root. 2. Invoke the sam utility by typing sam at the unix prompt. (w...

  • Page 163: Lp -D Lj4 Filename

    Iv - 69 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip h) allow anyone to cancel requests. Check if desired. I) remote printer is on a bsd system. Check this box. Tells the hp-ux system that it is communicating with a berkeley style remote printer (such as l...

  • Page 164: Kill -15 Process_Number.

    Iv - 70 section 4 - appendix b - application considerations oki okilan 6120e user’s guide • yourqueuename - this is the name of the queue on the okilan 6120e and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. If ff, lf or nf are the last two letters of the queu...

  • Page 165: Printer 515/tcp Spooler

    Iv - 71 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip 4. Make sure the following entry is in the “/etc/services” file: printer 515/tcp spooler 5. Start inetd by typing the following at the unix prompt: /etc/inetd -c procedure hp-ux uses an interactive utili...

  • Page 166: Lp -D Lj4 Filename

    Iv - 72 section 4 - appendix b - application considerations oki okilan 6120e user’s guide c) remote printer name - yourqueuename this is the name of the queue on the okilan 6120e and must end with 1, 2, 3 or 4, depending on the port selected to service the print jobs. D) remote cancel model - rcmode...

  • Page 167: With The Okilan 6120E

    Iv - 73 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip configuring sco unix for printing with the okilan 6120e this application note describes the configuration of the printing system on the santa cruz operation’s (sco) version of the unix operating system. ...

  • Page 168: Mkdir /usr/spool/lpd/lj4.

    Iv - 74 section 4 - appendix b - application considerations oki okilan 6120e user’s guide procedure 1. Login to the sco machine as root. 2. Install remote line printing or verify that it is running by typing mkdev rlp at the unix prompt. It will respond by asking if you want to install or remove rem...

  • Page 169: Okilan 6120E

    Iv - 75 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip ibm’s aix ver. 3.X for printing with the okilan 6120e this application note describes the configuration of the printing system on ibm’s aix version 3.X of the unix operating system. The following specifi...

  • Page 170: Okiprinter

    Iv - 76 section 4 - appendix b - application considerations oki okilan 6120e user’s guide 3. To add a remote queue, select the following options from the smit menu: spooler (print jobs and printers) manage remote printer subsystem client services remote printer queues add a remote queue a form appea...

  • Page 171: Aix> Startsrc -S Qdaemon

    Iv - 77 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip 6. Start the qdaemon by typing: aix> startsrc -s qdaemon 7. Try printing to the printer attached to the okilan 6120e by issuing the following command: aix> lpr -plj4 filename configuring solaris 2.X for ...

  • Page 172: 3. Type: Lpadmin -P Lj4 -S

    Iv - 78 section 4 - appendix b - application considerations oki okilan 6120e user’s guide prerequisites before you proceed, the following prerequisites must be met: 1. The name okiprinter and the ip address assigned to the okilan 6120e are in the “/etc/hosts” file on the solaris system. 2. Make sure...

  • Page 173: 6120E

    Iv - 79 section 4 - appendix b - application considerations oki okilan 6120e user’s guide tcp/ip configuring sun-os v4.1.X or ultrix v4.2 for printing with the okilan 6120e this application note describes the configuration of the printing system on the sun-os ver 4.1.X and ultrix ver. 4.2 of the uni...

  • Page 174: /usr/lib/lpd

    Iv - 80 section 4 - appendix b - application considerations oki okilan 6120e user’s guide if the lpd daemon is running, you should see output similar to: root 135 0.0 0.0 52 0 ? Iw may 24 0:01 /usr/lib/lpd if the lpd daemon is not running, start the daemon by logging into the sun-os or ultrix machin...

  • Page 175: Appendix C

    Iv - 81 section 4 - appendix c - internet printing protocol (ipp) oki okilan 6120e user’s guide tcp/ip appendix c internet printing protocol (ipp) internet printing protocol (ipp) is an application level protocol that can be used for distributed printing over the internet. Using the new ipp protocol...

  • Page 176

    Iv - 82 section 4 - appendix c - internet printing protocol (ipp) oki okilan 6120e user’s guide.

  • Page 177: Section V:

    Lan manager/ server section v: lan manager/lan server.

  • Page 178: In This Section

    V - 2 section 5 - lan manager/lan server oki okilan 6120e user’s guide in this section chapter 1 introduction ........................................... V-3 overview ....................................................... V-3 system requirements .................................... V-3 chapter 2 in...

  • Page 179: Chapter 1

    V - 3 section 5 - chapter 1 - introduction oki okilan 6120e user’s guide lan manager/ server chapter 1 introduction overview this section contains information about the okinet for os/2 utility. This utility allows you to install and configure the okilan 6120e for your specific environment. The utili...

  • Page 180

    V - 4 section 5 - chapter 1 - introduction oki okilan 6120e user’s guide dlc/802.2 protocol stack the dlc/802.2 protocol stack must be loaded and running on the file server from which the oki network printer redirector will run. With lan manager, this means you must enable the remote boot facility. ...

  • Page 181: Chapter 2

    V - 5 section 5 - chapter 2 - installation oki okilan 6120e user’s guide lan manager/ server chapter 2 installation overview to install the okilan 6120e: 1. Install the okinet for os/2 utilities software. 2. Run the okinet for os/2 utility to add a local printer port. 3. Associate a print queue with...

  • Page 182

    V - 6 section 5 - chapter 2 - installation oki okilan 6120e user’s guide • the initial installation requires the file server to be brought down and then back up again. This may be a consideration when you are planning your install. Depending on your current configuration, the following software may ...

  • Page 183: Running Install

    V - 7 section 5 - chapter 2 - installation oki okilan 6120e user’s guide lan manager/ server running install 1. Login to the server with administrator privileges. If you are reinstalling the utility, disable the spooler before running install. If this is the first time you have installed the utility...

  • Page 184: Port.

    V - 8 section 5 - chapter 2 - installation oki okilan 6120e user’s guide 3. Select ok. The print server status screen will display. From the configure menu, select add local port. 4. Select a print server and port. Print servers are identified by serial number. (you will find the serial number for y...

  • Page 185: Creating An Os/2 Printer

    V - 9 section 5 - chapter 2 - installation oki okilan 6120e user’s guide lan manager/ server creating an os/2 printer to print to the local port created by okinet for os/2, you must create an os/2 printer. Os/2 1.3 1. Open the print manager from the desktop. 2. Select setup from the menu. 3. Select ...

  • Page 186

    V - 10 section 5 - chapter 2 - installation oki okilan 6120e user’s guide printing a configuration sheet you can verify communication by printing a configuration sheet using okinet for os/2. 1. Select configure from the main print server window. 2. Select configure print server. 3. Select the okilan...

  • Page 187: Chapter 3

    V - 11 section 5 - chapter 3 - printing in the os2 environment oki okilan 6120e user’s guide lan manager/ server chapter 3 printing in the os/2 environment overview os/2 provides several methods for selecting a printer from within an application. The best method to use depends on the specific applic...

  • Page 188: Dos and Win-Os/2

    V - 12 section 5 - chapter 3 - printing in the os2 environment oki okilan 6120e user’s guide 3. Select the print queue associated with the okilan 6120e. Os/2 applications that use the default printer will now print to the printer attached to the okilan 6120e. The os/2 print screen function uses the ...

  • Page 189: Chapter 4

    V - 13 section 5 - chapter 4 - additional utility features oki okilan 6120e user’s guide lan manager/ server chapter 4 additional utility features overview you can run the okinet for os/2 utility at any time to access the following optional features: • deleting a local port • configuring a print ser...

  • Page 190: Configuring Parallel Port P1

    V - 14 section 5 - chapter 4 - additional utility features oki okilan 6120e user’s guide 3. From the configure menu, select configure print server. The following screen will display: the okilan 6120e will reset by selecting ok to save any of the options, except the print configuration sheet option. ...

  • Page 191: Restoring Factory Defaults

    V - 15 section 5 - chapter 4 - additional utility features oki okilan 6120e user’s guide lan manager/ server restoring factory defaults the restore defaults option restores the factory default settings for the lan manager/lan server protocol and output ports. To restore factory defaults, select an o...

  • Page 192: Chapter 5

    V - 16 section 5 - chapter 5 - using help oki okilan 6120e user’s guide chapter 5 using help overview the okinet for os/2 utility provides both general and context-specific help. General help to access help information about installation and configuration, select help from the main menu, then select...

  • Page 193: Appendix A

    V - 17 section 5 - appendix a - troubleshooting oki okilan 6120e user’s guide lan manager/ server appendix a troubleshooting no configuration sheet if the led turns solid orange due to a network protocol error and no configuration sheet is printed, your printer may be configured for postscript opera...

  • Page 195: Section Vi:

    W indows printing section vi: windows printing.

  • Page 196: In This Section

    Vi - 2 section 6 - windows printing oki okilan 6120e user’s guide in this section chapter 1 okilan 6120e set up for windows nt 4.0/2000 .......................................... Viii-3 overview ................................................... Viii-3 okilan 6120e connect for ip .....................

  • Page 197: Chapter 1

    Vi - 3 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide w indows printing chapter 1 okilan 6120e set up for windows nt 4.0/2000 overview this section contains instruction and information on how to set up your okilan 6120e for a windows nt 4.0/2000 environment. ...

  • Page 198: Name and Click Add.

    Vi - 4 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide installation to install okilan 6120e connect for tcp/ip, follow the instructions below: 1. Install the okilan 6120e connect for tcp/ip files - see section i. 2. When installation is complete, click on star...

  • Page 199: 7. Click Ok.

    Vi - 5 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide w indows printing note: the okilan 6120e connect dhcp discovery feature will relocate a print server on the local subnet by its port name, even if the ip address changes. This feature is enabled on the loc...

  • Page 200: Monitor

    Vi - 6 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide note: to obtain a version of okilan 6120e connect for dlc that supports windows nt, visit our ftp site (ftp://ftp.Extendsys.Com/pub/ printserver/utilities/) or contact technical support. Configure port if ...

  • Page 201: Click Ok.

    Vi - 7 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide w indows printing system requirements • administrator privileges • windows nt installation disks or cd install tcp/ip on nt server if microsoft tcp/ip has not been installed on the windows nt print server,...

  • Page 202: Add Printer.

    Vi - 8 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide add lpr printer 1. Open the control panel, printers and then select add printer. 2. Select my computer and click next. 3. Click the add port button. 4. On the printer ports screen, select lpr port from the...

  • Page 203: Next.

    Vi - 9 section 6 - chapter 1 - okilan 6120e setup for windows nt oki okilan 6120e user’s guide w indows printing 8. Verify the port just added is selected and then click next. 9. Select a printer driver and click next. 10. Enter a name for the printer and click next. 11. To share the printers with o...

  • Page 204: Chapter 2

    Vi - 10 section 6 - chapter 2 - okilan 6120e setup for windows 95/98 oki okilan 6120e user’s guide chapter 2 okilan 6120e set up for windows 95/98 overview this section contains instruction and information on how to set up your okilan 6120e for a windows 95/ 98 environment. Print options for windows...

  • Page 205: 6. Click Ok.

    Vi - 11 section 6 - chapter 2 - okilan 6120e setup for windows 95/98 oki okilan 6120e user’s guide w indows printing 3. Select the windows printer from which you would like to print with okilan 6120e connect, then select properties from the file menu. 4. Add an okilan 6120e connect port. This may be...

  • Page 206: Okilan 6120E Connect For Dlc

    Vi - 12 section 6 - chapter 2 - okilan 6120e setup for windows 95/98 oki okilan 6120e user’s guide you will now be able to use okilan 6120e connect for tcp/ip. Whenever you print to the printer configured with okilan 6120e connect, your print job will go directly to the okilan 6120e print server por...

  • Page 207: 6. Click Ok.

    Vi - 13 section 6 - chapter 2 - okilan 6120e setup for windows 95/98 oki okilan 6120e user’s guide w indows printing 5. In the add port window, select the radio button labeled other and select oki okilan 6120e connect dlc monitor as the type of port to add. 6. Click ok. You will enter into the add o...

  • Page 208: Enabling/disabling

    Vi - 14 section 6 - chapter 2 - okilan 6120e setup for windows 95/98 oki okilan 6120e user’s guide output port configuration options to configure the okilan 6120e output port, select the output port tab. Port number select the port number you wish to configure. Configuration page language select the...

  • Page 209: Section Vii:

    Okiview 32 section vii: okiview 32.

  • Page 210: In This Section

    Vii - 2 section 7 - okiview 32 oki okilan 6120e user’s guide in this section chapter 1 introduction ........................................ Vii-3 okiview 32 installation requirements ....... Vii-3 chapter 2 okiview 32 printer panel ................... Vii-4 okiview 32 printer properties menu .........

  • Page 211: Chapter 1

    Vii - 3 section 7 - okiview 32 oki okilan 6120e user’s guide okiview 32 chapter 1 introduction the okiview 32 utility provides a simple, quick way of viewing the status of all brands of network printers on microsoft/novell networks, as well as configuring and maintaining oki network printers on thos...

  • Page 212: Chapter 2

    Vii - 4 section 7 - okiview 32 oki okilan 6120e user’s guide chapter 2 okiview 32 printer panel the printer panel is the okiview 32 main display. The display is divided into two smaller panels: the printer filters panel and the printer information panel. The printer information panel, on the right h...

  • Page 213

    Vii - 5 section 7 - okiview 32 oki okilan 6120e user’s guide okiview 32 status the status screen is reached from the printer properties menu. This screen displays descriptive information about the printer, as well as its online/offline status and the status text displayed on the printer’s front pane...

  • Page 214

    Vii - 6 section 7 - okiview 32 oki okilan 6120e user’s guide changing the printer’s name and location 1 select a printer on the printer information panel. 2 from the printer menu, click printer properties. 3 change the text in the name and/or location fields. 4 click ok. Okiview 32 discovery prefere...

  • Page 215: Section Viii:

    Regulatory information section viii: regulatory information.

  • Page 216: Federal Communications

    Viii - 2 section 8 - regulatory information oki okilan 6120e user’s guide federal communications commission radio frequency interference statement this equipment generates and uses radio frequency energy. If not installed and used according to the manufacturer’s instructions, this equipment may caus...

  • Page 217: Index

    Index index a advanced management features network alert, ii-18 okinet for tcp/ip, ii-19 printer security for tcp/ip printing, ii-19 security, ii-5 advanced management features okinet for nds, ii-19 assigning an ip address bootp, iv-11 to iv-12, iv-57 to iv-59 dhcp, iv-10 gleaning, iv-9 rarp, iv-11 ...

  • Page 218

    Index - 2 index oki okilan 6120e user’s guide e enabling/disabling protocols okinet for netware, iii-17 okinet for tcp/ip, iv-32 error messages tcp/ip hardware, iv-53 f fcc statement, viii-2 federal communications commission statement, viii-2 ftp printing ascii, iv-20 binary, iv-20 bye, iv-20 close,...

  • Page 219

    Index - 3 index oki okilan 6120e user’s guide index l lan manager/lan server install, v-7 language switching netware, iii-11 to iii-12 n ndps,, iii-33 nds settings in netware, iii-9 nprinter mode in netware, iii-5 o okilan 6120e diagnostic information displaying in okinet for tcp/ip, iv-34 okinet co...

  • Page 220

    Index - 4 index oki okilan 6120e user’s guide output port configuration options in netware, iii-11 to iii-13 in tcp/ip, iv-28 to iv-30 p port configuration in netware, iii-10 print queue, configuring bsd-style, iv-17 to iv-18 print server class, adding or removing in okinet f, iii-31 to iii-32 print...

  • Page 221

    Index - 5 index oki okilan 6120e user’s guide index t tcp/ip configuration overview, iv-5 network printing, configur- ing for, iv-15 okilan 6120e connect for tcp/ip, vi-4 to vi-5 telnet session configuring port informa- tion, iv-46 to iv-47 identifying default gateway ip address, iv-46 running, iv-4...

  • Page 222

    Index - 6 index oki okilan 6120e user’s guide web jetadmin support, ii-8 to ii-9 configuring the okilan 6120e, ii-8 installing a windows nt printer, ii-8 to ii-9 obtaining diagnostic information, ii-9 windows 95 dlc requirements, vi-12 okinet connect for dlc, vi-12 to vi-13 okinet connect for tcp/ip...