Rancilio CLASSE 10 Use And Maintenance - page 21
78
0DFKLQHVZLWKL6WHDPDXWRPDWLFV\VWHP
)LJRQO\0RG86%
+HDWLQJ0LONRUD'ULQNL6WHPD
L
Immerse the wand in the drink
L
3UHVVEXWWRQRQWKHNH\SDG)LJ
L
7KHGLVSOD\ZLOOVKRZWKHWHPSHUDWXUHRIWKHGULQN
L
Press button 7.7 again to stop heating at the de-
sired temperature.
L
Wait for dispensing at the programmed tempe-
UDWXUHWRVWRSDXWRPDWLFDOO\RWKHUZLVHSUHVVNH\
7.7 in again to stop the drink-heating function
PDQXDOO\
Should heating the drink above the set temperature
EHUHTXLUHGKROGNH\SUHVVHGLQ
7KHVWHDPGLVSHQVHUQR]]OHZLOOFRQWLQXHVXSSO\LQJ
steam until a maximum temperature of approx. 90°C
LVUHDFKHGRUXQWLOWKHNH\LVUHOHDVHGDJDLQ
3UHSDULQJ)URWKHG0LONL6WHDP
L
Immerse the wand in a container containing at
least 250 cc of milk (the sensor must be at least 3
cm below the water level).
To obtain best results, use refrigerated milk (
d 5°C)
- (
d 41°F)
L
3UHVVEXWWRQRQWKHNH\SDG)LJ
L
7KHGLVSOD\VKRZVWKHWHPSHUDWXUHRIWKHPLON
L
Press button 7.6 again to stop the machine at the
desired temperature and emulsion level.
L
Wait for dispensing at programmed temperature and
DWSURJUDPPHGFUHDPOHYHOWRVWRSDXWRPDWLFDOO\
RWKHUZLVHSUHVVNH\LQDJDLQWRVWRSWKHGULQN
HPXOVLRQIXQFWLRQPDQXDOO\
$'-8670(17$1'6(77,1*2)7+(
DOSE
0RGHOV86%
It is possible to adjust the dose of coffee and hot water
GLVSHQVHGE\HOHFWURQLFDOO\FRQWUROOHGPRGHOV,IWKH
function is enabled)
$GMXVWLQJWKHGRVH
7KHTXDQWLW\RIFRIIHHDQGKRWZDWHUGLVSHQVHGFDQ
be adjusted using the button panel or the hot water
controls.
1 Press the button ERQDQ\EXWWRQSDQHODQGKROG
LWGRZQIRUVHFRQGVXQWLOZDWHUVWRSVÀRZLQJ
from the dispensing unit and the led of the conti-
QXRQVEXWWRQRQWKH¿UVWEXWWRQSDQHORQWKHOHIW
EHJLQVÀDVKLQJ
7KHIROORZLQJSDJHGLVSOD\LQJWKHVHUYLFHVVHOHF-
WLRQNH\SDGDQGWKHFRIIHHVHOHFWLRQZLOOFRPHXS
on screen.
,WLVQHFHVVDU\WRDFWDVWRPDNHRUFXSVLQRU-
der to reach the correct coffee amount adjustment
in the cup.
3XWWKH¿OWHUKROGHUZLWKJURXQGFRIIHHRQWKHOHIW
unit and the cup under the spout.
4 Operate the selected button (i.e. button A for one
small cup).
5 One the required coffee amount in the cup has been
reached, press the stop button A. Coffe will stop
pouring and the microprocessor will store the dose.
7KHVFUHHQZLOOGLVSOD\WKHLPSXOVHVUHODWLYHWRWKH
completed dose and a data box will highlight that
LWKDVEHHQVWRUHGLQWRWKHV\VWHP
6 Press the continuous button EDJDLQWKHOHGZLOOJR
RXWDQGWKHPDFKLQHZLOOVWRUHWKHQHZTXDQWLW\
7 Make the coffee and check the cup amount in order
to check that programming is correct.
If some doses have to be changed (A-B-C-D), once
at point 5 repeat the instructions in points 3-4-5 for
HDFKGRVHUHPHPEHULQJWRXVHWKH¿OWHUKROGHUZLWK
UHOHYDQW¿OWHUDQGIUHVKO\JURXQGFRIIHH
7KHQFDUU\RXWSRLQWDQGUHSHDWSRLQWWRFKHFN
all changed doses.
If all units are to be programmed with the same doses,
WKHVHOHFWLRQRIFRIIHHGRVHVLV¿QLVKHG,IWKHGRVDJH
of another unit is to be changed (1-2-3-4 doses), pro-
ceed as indicated in the above-mentioned point 1-7,
XVLQJRQO\WKHEXWWRQSDQHORIWKHVHOHFWHGXQLW
$GMXVWLQJWKHTXDQWLW\RIKRWZDWHU
Proceed as follows:
3UHVVWKHFRQWLQXRXV(EXWWRQRQDQ\EXWWRQSDQHO
and hold down for 8-10 seconds until water stops
ÀRZLQJIURPWKHGLVSHQVLQJXQLWDQGWKHOHGRIWKH
(EXWWRQRQWKH¿UVWEXWWRQSDQHORQWKHOHIWVWDUWV
ÀLVKLQJ7KHPDFKLQHLVUHDG\WRDFFHSWTXDQWLW\
variations.
2 Put a cup or a jug to receive the water under the
water spout 17 (Fig.3).
3XVKWKHGHOLYHU\EXWWRQ
4 Once the required amount is reached, press the
button 7.2 again. Water will stop pouring and the
microprocessor will store the dose.
- To adjust the water dose for the dispensing beak 4
)LJFDUU\RXWWKHVDPHVWHSVXVLQJHLWKHUNH\
7.3 or 7.4 or 7.5. Temperature-controlled water is
not dispensed during this phase.
5 Once adjusted, press the stop-continuous button
ERQDQ\EXWWRQSDQHOWKHOHGZLOOJRRXWDQGWKH
PDFKLQHZLOOVWRUHWKHQHZTXDQWLW\
6 Pour out doses of hot water to check that program-
ming is correct.