SAB Goblin 700 Manual - page 15
Center Hub
(H0410BL-S)
Linkage Rod
M3x50mm
(H0417-S)
Plastic Ball Link
(H0402-S)
Main Blade Grip
(H0182BL-S)
Bearing
10x 19x5mm
(HC422-S)
Blade Grip Arm
(H0183BL-S)
Plastic Ball Link
(H0402-S)
Right Side
Left Side
eg: Microlube GL261
A
Spindle
(H0412-S)
Main Blade Grip Assembly ....x2
Note: Large ID Inside
Socket Head Cap
Screw M6x10mm
(HC124-S)
Oring
(HA024)
Washer 6x 14 x1mm
(HC194-S)
Washer 10x 16x1mm
(HC230-S)
Thrust Bearing
10x 18x5.5mm
(HC438-S)
Center Hub Assembly
Radius Arm
(H0421BL-S)
Flanged Bearing
3x 7x3mm
(HC402-S)
Flanged Bearing
2.5x 6x2.5mm
(HC400-S)
Spacer Arm
(H0134-S)
Main Blade Grip
Assembly
Bearing
10x 19x5mm
(HC422-S)
Approx. 76mm
Radius Arm Assembly ... x 2
Uniball
(H0063-S)
Swashplate
Assemly
(H0420BL-S)
Uniball M3
(H0065-S)
Linkage Rod A Assembly . . . .x3
Linkage Rod A
Assembly
Linkage Rod B
Assembly
DETAIL A
(to adjust the tracking,
turn this linkage.)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Pin 5 mm
(H0413-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Damper Derlin
(H0426-C)
Uniball M3
(H0065-S)
Socket Head Cap
Screw M4x10mm
(HC102-S)
[HC230-S]
[HC232-S]
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Spacer Arm
(H0416-S)
Flanged Bearing
2.5x 6x2.5mm
(HC400-S)
Radius Arm
Assembly
Swashplate Assemly
Uniball Radius Arm
(H0415-S)
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Radius Arm
Assembly
Socket Head Cap
Screw M3x10mm
(HC056-S)
Washer 3x 4x0.5mm
(HC176-S)
M4x24mm
[HC111-S]
M3x12mm
[HC062-S]
Nut M4
[HC212-S]
[HC176-S]
Note:
The HPS3 head should be assembled with one, 1mm shim
(HC230) and one, 0.2mm shim (HC232) on each side.
The blade grips must move freely, but they should not
move just under their own weight.
If the blade grips are too tight, you can remove the
0.2mm shim (HC232) from each side.
After approximately 10/20 flights, please check preload,
you can add one or two 0.2mm shim (HC232) if preload
has changed.
(Initial length for the rods from the
swashplate to the Blade Grip.)
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust
tracking. If tracking is adjusted correctly,
you’ll see the metal part line up around
in the center of the opening.
BAG 7B, FOAM 3
Page 13
Chapter 6, Head