Sabo 52-S A Operator's Manual - page 60
8
GB
Maintenance and cleaning work must only be carried out if the engine has been turned off and the spark plug
connector has been removed.
Pos: 4.7.12 /Innenteil/Sicher hei tsvorschriften/Wartung und Lag erung/Kerzenstecker niemals bei laufendem M otor abziehen @ 13\mod_1280219056956_1521.doc @ 110075
• Never remove the spark plug connector when the motor is running! Risk: Electric shock.
Pos: 4.7.13 /Innenteil/Sicher hei tsvorschriften/Wartung und Lag erung/Tank nur i m Fr eien entleeren @ 0\mod_1115186486750_1521.doc @ 1649
• If the tank has to be emptied, this should be done in the open, and with a cold engine. Take care to ensure that no fuel
is spilt.
Pos: 4.7.14 /Innenteil/Sicher hei tsvorschriften/Wartung und Lag erung/Nur Original ersatzt eile ver wenden SABO @ 0\mod_1115186601093_1521.doc @ 1642
For warranty and safety reasons, original replacement parts must be used at all times.
Pos: 5.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.doc @ 2070
Pos: 5.2 /Innenteil/Beschr eibung der Bauteil e/1 BESCHREIBUN G D ER BAUT EILE @ 0\mod_1115187892468_1521.doc @ 1664
6 DESCRIPTION OF COMPONENTS
Pos: 5.3 /Innenteil/Beschr eibung der Bauteil e/Beschr eibung der Bauteil e 52- S A @ 22\mod_1359556284751_1521.doc @ 168397
1 Safety control bracket for the engine brake
2 Handlebar-upper part
3 Bar screws
4 Handlebar-lower part
5 Oil-refill neck with measuring rod
6 Engine cover
7 Exhaust protection grid
8 Ignition plug
9 Cutting height adjuster
10 Deflector
11 Air filter
12 Rear driving wheels
13 Belt drive covers
14 Tank cap
15 Starter cable grip
16 Drive control bracket
Pos: 6.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.doc @ 2070
Pos: 6.2 /Innenteil/Vor ber eitende Ar beiten/1 VOR BER EIT ENDE AR BEITEN @ 0\mod_1115194917734_1521.doc @ 1672
7 PREPARATION
Pos: 6.3 /Innenteil/Vor ber eitende Ar beiten/Vor ber eitende Ar beiten T ext 52-S @ 15\mod_1302699952233_1521.doc @ 127130
The following unit parts are included in the package for mower assembly:
• Mower
• Handlebar-lower part
• Handlebar-upper part
• Bar support
• Ejection flap
• Tool bag with the following content:
• Operating instructions with Declaration of Conformity
• Guarantee card and guarantee conditions
• Diverse fastening parts.
Should any part be missing, please contact your professional dealership.
Pos: 6.4 /Innenteil/Vor ber eitende Ar beiten/1.1 H olmabst ützung anbauen (Abbildung B ) @ 15\mod_1302700266608_1521.doc @ 127146
Attach bar support (Illustration B )
Pos: 6.5 /Innenteil/Vor ber eitende Ar beiten/H olmabst ützung anbauen T ext @ 6\mod_1186403846453_1521.doc @ 38120
– Position the handle support on the two preassembled screws between the rear wheels.
– Tighten by hand with a curved washer and a hexagon heat nut.
Pos: 6.6 /Innenteil/Vor ber eitende Ar beiten/1.1 F ühr ungshol m-U nterteil anbauen (Abbildung B ) @ 15\mod_1302700745872_1521.doc @ 127162
Attach handlebar-lower part (Illustration B )
Pos: 6.7 /Innenteil/Vor ber eitende Ar beiten/F ühr ungshol m-U nterteil anbauen T ext 52-S @ 15\mod_1302701086615_1521.doc @ 127178
– Insert an M 8 hex nut into each of the two cams on the mower housing in front the rear wheels.
– Attach the outer parts of the two bar ends to the cams.
– Place a washer and then a spacer on each of the two fastening hex screws.
– Fix the two screws into the cams through the bar ends.