Safewatch QuickConnect Plus Programming Manual - page 3
- 3 -
To Initialize Download ID and Subscriber Account Number for Downloading:
✻
96 Resets all subscriber account numbers and CSID in preparation for an initial download.
To Load a Default Set:
✻
97 Enter a number 1-4 corresponding to the selected default table (See the Installation Instructions for the
default tables). Enter 0 if you are not selecting a default table.
To Exit Programming Mode:
✻
98 Exits programming mode and prevents re-entry by: Installer Code + 8+ 0 + 0. If ✻98 is used to exit
programming mode, system must be powered down, then press [✻] and [#] within 50 seconds of power
up to re-enter programming mode.
✻
99
Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or: Power-up, then press [✻]
and [#] within 50 seconds of power up.
DATA FIELDS
Data Field Display
Function& Programming Options
[ ] = Programmed Table 1 Default Values
SYSTEM SETUP (✻20– ✻30)
†
Entering a number other than the one specified may give unpredictable results.
20
20
20
20
INSTALLER
INSTALLER
INSTALLER
INSTALLER CODE
CODE
CODE
CODE
Installer Code
[6321]
Enter 4 digits, 0–9
21
21
21
21
QUICK
QUICK
QUICK
QUICK ARM
ARM
ARM
ARM ENABLE
ENABLE
ENABLE
ENABLE
Quick Arm Enable
†
[1]
0 = no; 1 = yes
22
22
22
22
KEYPAD
KEYPAD
KEYPAD
KEYPAD BACKLIGHT
BACKLIGHT
BACKLIGHT
BACKLIGHT
Keypad Backlight Timeout
[0]
0 = none (backlighting always on); 1 = backlight off after 10secs
23
23
23
23
FORCED
FORCED
FORCED
FORCED BYPASS
BYPASS
BYPASS
BYPASS
Forced Bypass
UL installations = 0
†
[1]
0 = none; 1 = bypass open zones
24
24
24
24
RF
RF
RF
RF HOUSE
HOUSE
HOUSE
HOUSE ID
ID
ID
ID CODE
CODE
CODE
CODE
RF House ID Code
|
[00]
00 = disable all wireless keypad usage; 01–31 = 5804BD/5804BDV house ID
25
25
25
25
X10
X10
X10
X10 HOUSE
HOUSE
HOUSE
HOUSE CODE
CODE
CODE
CODE
Powerline Carrier Device (X10) House ID
[0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 =
J, #10 = K, #11 = L,
#12 = M, #13 = N, #14 = O, #15 = P
26
26
26
26
CHIME
CHIME
CHIME
CHIME BY
BY
BY
BY ZONE
ZONE
ZONE
ZONE
Chime By Zone
† [0]
0 = no; 1 = yes (program zones to chime on zone list 3)
27
27
27
27
CLO
CLO
CLO
CLOCK
CK
CK
CK DISPLAY
DISPLAY
DISPLAY
DISPLAY
Real Time Clock Display
† [1]
0 = no; 1 = yes, display time on keypad
29
29
29
29
DST
DST
DST
DST MNTH
MNTH
MNTH
MNTH STR/END
STR/END
STR/END
STR/END
Daylight Saving Time Start/End Month
[3, 11]
Start
End
1-9, #+10,#+11,#+12. Enter 0,0 if no daylight savings time used.
30
30
30
30
DST WEEK STR/END
DST WEEK STR/END
DST WEEK STR/END
DST WEEK STR/END
Daylight Saving Time Start/End Weekend
[2,1]
Start
End
0=disable; 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to last; 7=third from last