Safewatch QuickConnect Plus Programming Manual - page 9
- 9 -
Data Field Display
Function& Programming Options
[ ] = Programmed Table 1 Default Values
74
74
74
74
LO
LO
LO
LO BAT
BAT
BAT
BAT RES
RES
RES
RES REP
REP
REP
REP
Low Bat Restore Report Code
|
[1,0]
75
75
75
75
RF
RF
RF
RF LOBAT
LOBAT
LOBAT
LOBAT R
R
R
RES
ES
ES
ES REP
REP
REP
REP
RF Transmitter Low Battery Restore Report Code
|
[1,0]
76
76
76
76
TEST
TEST
TEST
TEST RES
RES
RES
RES REPORT
REPORT
REPORT
REPORT
Test Restore Report Code
|
[1,0]
DYNAMIC SIGNALING FIELD (✻77)
77
77
77
77
DYNAMIC SIG OPTS
DYNAMIC SIG OPTS
DYNAMIC SIG OPTS
DYNAMIC SIG OPTS
Dynamic Signaling Options
| [0, 0]
1st Entry
(delay before switch CS reporting path)
0 = Redundant
reporting on dialer
and LRR/IP device
1 = 15 seconds
2 = 30 seconds
3 = 45 seconds
4 = 60 seconds
5 = 75 seconds
6 = 90 seconds
7 = 105 seconds
8 = 120 seconds
9 = 135 seconds
#10 = 150 seconds
#11 = 165 seconds
#12 = 180 seconds
#13 = 195 seconds
#14 = 210 seconds
#15 = 225 seconds
2nd Entry
0 = Primary Dialer
Preferred Channel
1 = LRR/IP
Preferred Channel
2 = LRR/IP
reporting only
7
77
78
8
8
8
PROG TONE GEN TM
PROG TONE GEN TM
PROG TONE GEN TM
PROG TONE GEN TM
Programmable Tone Generation Time
| [0, 0]
00 = Disabled
01-09 = 100-900 ms
10-99 = 1.0 – 9.9 secs
OUTPUT AND SYSTEM SETUP (✻80, ✻81, ✻83–✻85)
See Procedures later in this manual.
86
86
86
86
MULTI
MULTI
MULTI
MULTI----MODE
MODE
MODE
MODE EMAIL
Multi-Mode (E-Mail Notification)
(RIS is always enabled)
[0]
0 = Disable multi-mode devices (RIS enabled)
1 = Enable multi-mode device address #6 only (RIS enabled)
2 = Enable multi-mode device address #7 only (RIS enabled)
3 = Enable multi-mode addresses (RIS enabled)
87
87
87
87
AUX
AUX
AUX
AUX FUNC
FUNC
FUNC
FUNC 1BTN
1BTN
1BTN
1BTN PG
PG
PG
PG
Aux Function/ 1-Button Paging
[0]
0 = Aux key performs defined function (macro);
1 = Aux key sends message to pager or voice message to follow me system phone no.
If 1, you must also select an option 6-9 in field ✻49 for the pager or 10-13 for the follow me
system announcement.
88
88
88
88
PAGER CHARACTERS
PAGER CHARACTERS
PAGER CHARACTERS
PAGER CHARACTERS
Pager Characters
Up to 16 digits can be entered that will appear in front of the 7-digit pager message sent by
the control. Refer to the Installation Instructions (fields ✻87, ✻88 and ✻49) for full
descriptions of the paging feature. You do not need to fill all 16 digits (press [✻] to
advance to next field).
To clear entries, enter ✻88✻. To enter “✻” = [#] + [11]; To enter “#” = [#] + 12]; To
enter 2-second pause = [#] + [13] (some pagers require an additional delay [pause] in
order to receive the entire message)
89
89
89
89
EVNT
EVNT
EVNT
EVNT LOG
LOG
LOG
LOG 80%
80%
80%
80% REP
REP
REP
REP
Event Log 80% Full Report Code
|
[0,0]