Smartlink MEDI-CALL UNIT Installation Manual - page 30
Medi-Call V2.0 – V2.7 Installation Manual
29
9 . V O I C E A N N U N C I A T O R
9.1 “HANDS FREE” PHONE OPERATION
Ademco and British DTMF Versions:
• Uses the SmartLink CANCEL (Green) Button to answer or hang up an incoming telephone call “hands free”.
• Uses the PANIC Button (Keys programmed with “An” ANSWER option) or the OFF Button (Keys programmed with
“Sc” SECURITY option) to answer or hang up an incoming telephone call “hands free”.
NOTE: “Hands free” is a two-way communication over the telephone and is not effected by the “SH” QUIET option.
Contact ID Version:
• Uses the SmartLink CANCEL (Green) Button to answer or hang up an incoming telephone call “hands free”.
• Uses the OFF Button (any Keys programmed with “Pn” PANIC, “dP” DELAY PANIC or “du” DURESS option) to
answer or hang up an incoming telephone call “hands free”.
9.2 AUTO ANSWER AND REMOTE VOICE CONTROL
9.2.1 AUTO ANSWER
When an alarm is sent to the Control Centre, the voice circuits are enabled for the amount of minutes programmed in the
“Ac” ANSWER CALL option. (Any incoming call within this time will be automatically answered). The SmartLink unit
will then output tones and or annunciate “Alarm” to indicate the phone has been answered. The originator (Control Centre)
of the call back must press the # Key on their telephone within 30 seconds of the Smartlink unit answering, establishing a 3
minute voice connection between both parties. Failure to press the # Key will result in the Smartlink unit disconnecting.
Time can be extended in 3 minute blocks by pressing the # Key within 30 seconds after the warning tones (every 2 minutes
and 30 seconds). When a call is terminated the voice circuits are enabled for the time period programmed in the “Ac”
ANSWER CALL, so that any incoming call during this time will be automatically answered again.
Press the CANCEL (Green) Button on the SmartLink unit or any OFF Button (Radio Key Pendants) to immediately hang
up the call and inhibit any more Auto Answering for that alarm.
Ademco and British DTMF Versions:
• If “SH” QUIET option is Disabled, then the SmartLink unit will answer the call after the number of rings programmed
in “rd” RINGS DETECTED (2-9 Rings) option.
• If “SH” QUIET option is Enabled, then the SmartLink unit will answer in Listen Mode Only immediately after
detection of ringing.
• The program option “C1” – “C8” CALL BACK ON CHANNEL 1 – 8 effect the Ademco Channel. For example if
“C7” is Disabled then call back will not be available on INACTIVITY, CALL7, INPUT3 and HELP7 alarms, basically
any alarm sent on Channel 7.
Contact ID Version:
• If a Radio Key Pendant is programmed with the “du” DURESS option or a Detector with the “Si” SILENT option,
SmartLink unit will override the option and assume the option was Enabled. The call would have been answered in a
Listen Mode Only where the speaker is Disabled.
• The program option “C1” – “C8” CALL BACK ON CHANNEL 1 - 8 only effects alarms of individual Detectors. For
example, “C2” option is Disabled so call back will not be available on any alarm generated by Detector 2.
9.2.2 REMOTE VOICE CONTROL
Enhance Microphone Sensitivity: Press 3 Key
The SmartLink unit may be enhanced during an emergency call so that quiet or distant voices may be detected. Pressing the
3 Key on the Control Centre’s telephone will increase microphone sensitivity and the SmartLink unit speaker will be
Disabled. Pressing the 3 Key again will Disable the enhanced mode (Toggles back and forth). The SmartLink unit will
respond with 2 beeps to indicate the beginning of enhanced mode and 1 beep to indicate dropping out of enhanced mode.
Hang Up: Press * (Star) Key Twice
Pressing * (Star) Key twice on the telephone will terminate the call. The voice circuits will remain Enabled for 6 minutes
(as programmed in the “Ac” ANSWER CALL) so that any incoming call within this time will be automatically answered.
Hang Up: Press * (Star) and # (Hash) Key
Pressing * (Star) Key and then # (Hash) Key on the telephone will terminate the call.
The voice circuits will be Disabled and SmartLink unit will not auto answer any incoming call.
NO RESTORE message will be sent to the Control Centre.