Smartlink MEDI-CALL UNIT Installation Manual - page 8
Medi-Call V2.0 – V2.7 Installation Manual
7
5.2 PROGRAMMING SUB MENU OPTIONS
The Sub Menu Options are displayed for each particular Main Menu Option.
5.2.1 KEYS (PENDANTS) PROGRAMMING OPTIONS
Option Description (Note: ADEMCO and BRITISH DTMF Versions)
USER KEY 1 (PENDANT) PROGRAMMING
un-programmed
No Radio Key Pendant has been programmed for User Key 1
Help
Where
ON = Call
OFF = Call
PANIC = Call
(V2.0 - V2.2) Call
Where
ON = Call
OFF = Restore
PANIC = Call
(V2.3 onwards) Call
Where
ON = Emergency OFF = Restore
PANIC = Emergency
(V2.3 onwards) Help-Call
Where
ON = Call
OFF = Restore
PANIC = Emergency
(V2.3 onwards) Call-Help
Where
ON = Emergency OFF = Restore
PANIC = Call
(V2.0 - V2.2) Restore
Where
ON = Restore
OFF = Restore
PANIC = Call
Security
Where
ON = Arm
OFF = Disarm
PANIC = Call
Answer
1 Button Key where PANIC-Initiates Call or if rings are detected will
answer the incoming phone call.
Dementia
1 Button Blue Radio Key initiates Call on inactivity.
(V2.5 onwards) Door Bell 1
1 Button Key where PANIC-Initiates Door Bell Tune 1.
(V2.5 onwards) Door Bell 2
1 Button Key where PANIC-Initiates Door Bell Tune 2.
(V2.5 onwards) Door Bell 3
1 Button Key where PANIC-Initiates Door Bell Tune 3.
Erase
Remove previously Programmed Radio Key.
To Program a NEW Radio Key Pendant (User Key):
1. “u1” is displayed on the SmartLink unit. Press the HELP Button on the SmartLink unit.
2. The SmartLink unit must display “- ” (unprogrammed). Press any Button on a NEW Radio Key Pendant 3
times. The SmartLink unit will beep with each Button press and on the third Button press, beep twice to
acknowledge the Radio Key Pendant is programmed. The status display will also display and flash “Hl”
(Help) to indicate that the Radio Key Pendant is programmed.
NOTE: If the SmartLink unit gives a long beep on Button presses and displays “- ” it indicates that the
Radio Key Pendant has already been programmed into the SmartLink unit.
3. Then, using the HELP Button to select an option for the Radio Key Pendant.
4. To store an option selected, press the CANCEL and HELP Buttons at the same time. The SmartLink unit
will beep twice while flashing the display to acknowledge that the option has been selected.
5. Press the CANCEL Button to move to the next Program Option.
To Erase a Radio Key Pendant (User Key):
1. Go to the Pendant Option you wish to erase “u1” to “u8”.
2. Then, using the HELP Button to select an option “Er” (Erase).
3. Press the CANCEL and HELP Buttons at the same time. The SmartLink unit will beep twice while
flashing the display “- ” to indicate that a Radio Key Pendant has been erased.
4. Press the CANCEL Button to move to the next Program Option.
USER KEYS (PENDANTS) 2 – 8 PROGRAMMING
DEFAULT VALUES –
Erases all Programmed User Keys (Pendants) u1 to u8
To Erase all Programmed User Keys (Pendants) u1 to u8:
1. “dF” is displayed on the SmartLink unit.
2. Press the HELP Button. The SmartLink unit will beep twice while flashing the display “- ” to indicate
that ALL Radio Key Pendants (User Keys u1 to u8) have been Erased.
3. Press CANCEL Button to move to the next Program Option.