1. DL manuals
  2. Xpresskit
  3. Door locks
  4. DBALL2
  5. Installation Manual

Xpresskit DBALL2 Installation Manual

Manual is about: Firmware: MA2

Summary of DBALL2

  • Page 1

    Update alert: firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Vehicle application guide.....................................................................................................

  • Page 2

    Vehicle application guide page 2 the following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles 2 0 1 8 2 0 1 7 2 0 1 6 2 0 1 5 p k -u n iv e rs a l...

  • Page 3: Remote

    Not required in d2d mode. 1: green: (-) lock input 2: blue: (-) unlock input 9: pink: (+) ignition input 10: blue/white: (-) gwr (status) input (-) gwr (status) (+) ignition output (-) lock output (-) unlock output [2] key wrap: brown/red: 12 [2] key wrap: yellow/red: 11 [2] key wrap: orange/red: 10...

  • Page 4

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 4 type 1 - vehicle wiring reference chart vescm - vehicle electrical system control module at driver side under dash, above driver kick panel locating components in the vehicle esclcm - electronic steering colu...

  • Page 5: Remote

    1: green: (-) lock input 2: blue: (-) unlock input 9: pink: (+) ignition input 10: blue/white: (-) gwr (status) input (-) gwr (status) (+) ignition output (-) lock output (-) unlock output [2] key wrap: brown/red: 12 [2] key wrap: yellow/red: 11 [2] key wrap: orange/red: 10 (-) ground: black: 14 (-)...

  • Page 6

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 6 type 2 - vehicle wiring reference chart vescm - vehicle electrical system control module at driver side under dash, above driver kick panel a2 a3 a1 locating components in the vehicle function color pin polar...

  • Page 7: Remote

    Not required in d2d mode. 1 13 12 37 62 73 38 63 (-) gwr (status) (+) ignition output (+) parking light output (-) lock output (-) unlock output 8 16 obdii diagnostic connector 1 9 hs can 1 high: orange/red, pin 6 hs can 1 low: orange/brown, pin 14 (+) 12v input (+)12v: red/white, pin 1 1: green: (-...

  • Page 8

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 8 type 3 - vehicle wiring reference chart function color pin polarity location color pins volkswagen golf alltrack (smart key) 2017 hs can 1 high orange/red 6 data obdii. Black 16 hs can 1 low orange/brown 14 d...

  • Page 9

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 9 vescm - vehicle electrical system control module at driver side under dash, above driver kick panel locating components in the vehicle esclcm - electronic steering column lock control module at steering colum...

  • Page 10

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 10 method 1: immobilizer interface with oem immob. Receiver push-to-start (pts) note: - your oem remote may differ from the model shown in the illustrations. - remove battery from oem fob prior to performing th...

  • Page 11

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Method 3: key wrap for push-to-start (pts) using oem immobilizer ring. Oem immobilizer receiver 10 dball2 rf prog. Button led 4 14 12 2 no relay 2: brown/red: 12 common relay 2: yellow/red: 11 nc relay 2: orange/red...

  • Page 12

    Module programming page 12 important make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Warning! To take advantage of advanced features, you must use xpressv...

  • Page 13

    2 solid & solid flashes & release 3 wait 3 seconds until the led turns on solid orange, and wait 10 more seconds until the led starts to flash orange and red. Release the programming button. The led turns on solid red. Warning against executing a hard reset! A hard reset will revert the flashed firm...

  • Page 14

    Page 14 to enter feature programming routine - turn the ignition on, then off. - within 5 seconds, press and hold the programming button until the led turns on orange (after 3 seconds). Release the programming button. - the led will flash green once slowly to indicate the feature number is 1. After ...

  • Page 15

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. Page 15 led diagnostics & troubleshooting led description troubleshooting module has no power. Make sure the d2d harness is connected or that the 12 volt is present between the red and black wires. If the 12 volt is...

  • Page 16

    Rev.: 20171012 platform: dball2 firmware: vw06 © 2017 directed. All rights reserved. (flashes red, red then orange) x 10 flashes red & orange flashes red x 21 flashes red x 2 flashes red x 4 flashes red x 10 flashes red x 1 flashes red x 3 flashes green flashes green quickly flashes green x 1 flashe...

  • Page 17

    For a period of one year from the date of purchase of a directed electronics remote start or security product, directed electronics. (“directed”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter ...

  • Page 18

    Quick reference guide dball2-vw06 © 2017 directed. All rights reserved. 1 stop the vehicle in a safe parking spot and put the gear in park (p). * your aftermarket remote may differ from the model shown in the illustrations. Stop & put vehicle in park (p) p & exit vehicle with key pit stop mode the p...

  • Page 19

    Quick reference guide dball2-vw06 © 2017 directed. All rights reserved. Notes button(s) actions press & hold for 1 second to lock. Press & hold for 1 second to unlock. Press & hold for 1 second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to ...