Xpresskit DBALL2 Installation Manual - Remote
Not required in D2D mode.
1
13
12
37 62
73
38
63
(-) GWR (Status)
(+) Ignition Output
(+) Parking Light Output
(-) Lock Output
(-) Unlock Output
8
16
OBDII
Diagnostic
Connector
1
9
HS CAN 1 High: Orange/Red, pin 6
HS CAN 1 Low:
Orange/Brown, pin 14
(+) 12V Input
(+)12V:
Red/White,
pin 1
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
9: Pink: (+) Ignition Input
8: Violet: (+) Parking Light Input
10: Blue/White: (-) GWR (Status) Input
HS CAN 1 High: Tan/Black: 3
HS CAN 1 Low: Tan: 4
[2]
Key Wrap: Brown/Red: 12
[2]
Key Wrap: Yellow/Red: 11
[2]
Key Wrap: Orange/Red: 10
HS CAN 2 High: Orange/Green: 5
HS CAN 2 Low: Orange/Brown: 6
(+) Parking Light Output: Brown: 7
Parking Light Interrupt (vehicle side): Yellow: 8
Parking Light Interrupt (conn. side): Orange/Yellow: 9
(-) Ground: Black: 14
(-) Ground
(+) 12V: Red: 13
(+) 12V
(-) PTS 1 Output: Green/Black: 2
(-) Door Status Output: Green/White: 3
[1]
(AC) Tach Output: Violet/White: 5
(-) Trunk Status Output: Red/Black: 4
(-) Hood Status Output: Blue/Red: 12
(+) Brake Status Output: Gray: 6
(+) Ignition Status Output: Gray/Black: 7
(-) PTS 2 Control: Violet/Brown: 9
3: Red/White: (-) Trunk Release Input
(-) Trunk Release Output
Remote
Starter
A1
A2
A3
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16
(-) PTS 1:
Violet/Blue, pin 4
(-) PTS 2:
Violet, pin 13
HS CAN 2 High:
Orange/Green,
pin 16
HS CAN 2 Low:
Orange/Brown,
pin 15
Electronic Steering
Column Module
(black conn. under column)
(-) Door Status Input
[1]
(AC) Tach Input
(-) Hood Status Input
(+) Ignition Status Input
(-) Trunk Status Input
(+) Brake Status Input
(+) Starter Output
(+) Brake:
Black/Red,
pin 58
Parking Light Interrupt
Red/White, pin 8
Headlight Switch
(red conn. at light switch)
(+) Parking Light:
Gray/Yellow,
pin 3
10 9
8 6
5 4
2 1
8
3
CUT
White VESCM Connector A3
(above drivers kick)
VESCM: Vehicle Electrical
System Control Module
(high above drivers kick)
(-) Ground
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog. Button
LED
4
14
12
2
DBALL2
Page 7
Installation Type 3
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2]
For Key Wrap instructions refer to page 9.
Rev.: 20171012
Platform: DBALL2
Firmware:
VW06
© 2017 Directed. All rights reserved.