1. DL manuals
  2. Xpresskit
  3. Door locks
  4. DBALL2
  5. Installation Manual

Xpresskit DBALL2 Installation Manual

Manual is about: Firmware: MA2

Summary of DBALL2

  • Page 1

    Index installation guide update alert: firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. ® are registered trademarks and property of . Buick, chevrolet and their respective companies. Gmc...

  • Page 2

    Vehicle application guide page 2 the table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles. [2] t-harness 610 is compatible with these models the...

  • Page 3

    Note: diagnostic connector ( ) obdii functions will remain identical even with the t-harness installed. 1. Remove the factory diagnostic connector ( ) from the dash. Obdii 2. Screw style (# 1/ d1) or clip obdthdgm obdgm style (# 2/ d2) obdthdgm obdgm the black female connector to replace the factory...

  • Page 4

    [1] hs can high: 3 tan/black: (+) 12v: 13 red: (-) ground: 14 black: diagnostic connector (connector side view) obdii 1 8 16 9 single wire can: 1 light green: [1] tan: hs can low: 4 important! Refer to the quick reference guide for more information on range extender ready ( ). Rxt sw c : pin 1 an gr...

  • Page 5

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 5 fu...

  • Page 6

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 6 fu...

  • Page 7

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 7 fu...

  • Page 8

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 8 fu...

  • Page 9

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 9 fu...

  • Page 10

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 vehicle wiring reference chart wire colors should only be used as a reference. You should always test a wire's function and pin location before connecting to it. Page 10 f...

  • Page 11: Xl202

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 smartstart/ 202 installation notes xl page 11 th solution offers t ( ) configuration options to control your system kit or e range extender ready ( ) wo 2 : dball rxt rf b...

  • Page 12

    Page 12 module programming 2 3 5 times on the programming button press then the key to the turn ign position. The orange for 3 seconds . Led turns solid , then shuts on off & & solid x3 secs off press x5 key in off start ign you have successfully completed the module programming sequence. 1 10-pin d...

  • Page 13

    Page 13 module reset 1 if required for your installation, connect the 10-pin & 12-pin harnesses to the module press hold the rogramming . And p button, then connect the 14-pin harness to the module. 10-pin d2d 1 st 12-pin 14-pin 2 nd 4 th 3 rd warning gainst xecuting a hard reset! A e a hard reset w...

  • Page 14

    Page 14 feature option list & it is recommended to configure all features and options listed below the the using configuration tool found on the module flashing page on www.Directechs.Com. The web offers more options such as ; however, manual configuration of the features is possible using rsr the i...

  • Page 15

    Page 15 to enter feature programming routine - turn t , then he ignition . On off - within 5 seconds, press and the rogramming button turns after 3 seconds . Release the hold led on p until the orange ( ) programming button. - the to indicate the feature number is 1. After a short delay, the flashes...

  • Page 16

    Page 16 led diagnostics & troubleshooting led description troubleshooting module has no power. Make sure the d2d harness is connected or that the 12 volt is present between the red and black wires. If the 12 volt is present, the module may be defective. Waiting to begin the programming sequence. Ens...

  • Page 17

    © 2017 directed. All rights reserved. Platform: dball2 firmware gm10 range extender ready (rxt) installation : rev.: 20 70 1 821 led description troubleshooting obdii feature is not supported. The diagnostic data bus was not detected, therefore the smartstart features will be limited. Ground when ru...

  • Page 18

    Page 8 1 limited consumer warranty one year for a period of from the date of purchase of a directed electronics remote start or security product, directed one year electronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the directed security...

  • Page 19

    Quick reference guide dball2- range extender ready (rxt) installation gm10 © 2017 directed. All rights reserved. Range extender ready ( ) is used to amplify the distance covered rxt by factory remote starters, which are built into the of the vehicle. Bcm the interface connects to the vehicle and use...

  • Page 20

    Quick reference guide dball2- range extender ready (rxt) installation gm10 © 2017 directed. All rights reserved. Notes smartstart compatible this system is compatible with directed smartstart 3.0. For a complete list of supported features, please visit www.Mysmartstart.Com. What is smartstart? Now y...