Xpresskit DBALL2 Installation Manual - Remote
Wiring Diagram
Page 3
Remote
Starter
(-) GWR (Status)
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
(+) Parking Light Output
(+) Ignition Output
10
DBALL2
RF
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
7: Pink/White: (+) Parking Light Input
10: Blue/White: (-) GWR (Status) Input
4
TX
(-) Ground
RX
(+)12V
14
12
2
Parking Light Interrupt. (car side): Yellow: 8
(MUX) Parking Light Input.: Brown: 7
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Parking Light Interrupt. (conn. side): Orange/Yellow: 9
(+) Brake Output: Gray: 6
[3]
(-) Hood Status Output: Blue/Red: 12
(+) Ignition Status Output: Gray/Black: 7
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(-) (AC) Tach Output: Violet/White: 5
P#: XKD2D65
(-) Ground: Black: 14
(+) 12V: Red: 13
(MUX) Parking Light Output: Violet/Brown: 9
(MUX) Parking Light:
White/Brown, pin 1
(+) Ignition/Start Enable:
Pink/White, pin 1
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
MS CAN Low: Orange/Brown: 6
[2]
MS CAN High: Orange/Green: 5
Black conn.
(Located at Parking
Light Switch)
1
2 3 4
9
8
7
6
5
10
1
8
16
9
C-CAN High:
Gray/White, pin 6
[2]
IHS CAN High:
Gray, pin 3
C-CAN Low:
Yellow, pin 14
[2]
IHS CAN Low:
White, pin 11
OBDII
Diagnostic
Connector
(-) Ground
[2]
Required for RAP, heated seats, steering wheel and rear defroster control.
[3]
Some vehicles are not equipped with OEM hood pin and require the addition of a hood pin for hood sensing.
(+) 12V: Brown/Red: 12
(+) Ignition/Start Enable: Yellow/Red: 11
Black 59-pin connector
(Located at link connector attached
to the dash frame close to the top
left front of the BCM)
59
18
58
17
57
16
56
15
55
14
54
13
53
12
52
11
51
10
19
20
21
22
23
24
25
26
28
27
29
30
31
32
40
33
34
35
36
37
38
39
41
50
9
49
8
48
7
47
6
46
5
45
4
44
3
43
2
42
1
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Input
[3]
(-) Hood Status Input
(+) Ignition Status Input
(-) E-Brake Status Input
(-) Ground
(+) 12V
(+) 12V:
Red or
Red/Lt. Green,
pin A
Blue 2-pin conn.
(located at BCM/dash fuse box)
(-) Ground
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
A
B
Rev.: 20160201
Platform: DBALL2
Firmware:
CHRYSLER10
© 2016 Directed. All rights reserved.
Wire jump template
You have successfully completed the module programming sequence.
Once the configuration is completed, reconnect the module.
The LED turns solid green for 3 sec. then OFF.
Click on Submit Key2GO Request.
Remove the DBALL from the vehicle and reconnect it to your computer. The Directechs web site will
automatically recognize that you are moving onto the second phase of the programming sequence.
Solid
x3 sec.
Off
7
6
5