Xpresskit DBALL2 Installation Manual - page 8
Feature and Option List
Feat.
Operation
Flashes / Option
Description
1. No RF Output*
Module is connected to a remote starter using a standard installation.
2. RFTD Output
Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart
Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority*
Unlocks only the driver door when the button is first pressed, and unlocks all doors
when it is pressed a second time within 5 seconds.
2. All
Unlocks all doors when the button is first pressed.
1. Disabled*
No operation.
2. Enabled
When the feature is enabled, it will activate the Heated Seats and heated steering
wheel.
1. Disabled*
No operation.
2. Enabled
When the feature is enabled, it will activate the rear defroster and heated mirrors.
1. 32°F ( 0°C)*
When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 32 °F (0 °C).
2. 23°F (-5°C)
When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 23 °F (-5 °C).
3. 41°F (+5°C)
When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 41 °F (5 °C).
4. Always ON
When Heated Seats or Defroster feature is enabled, it will activate the feature at any
temperature.
1. High*
When Heated Seats are activated, they will be set to HIGH.
2. Low
When Heated Seats are activated, they will be set to LOW.
1. Disabled*
The vehicle doors will not lock automatically.
2. Ignition
The vehicle doors will lock when ignition is turned ON and unlock when ignition is OFF.
3. Brake
The vehicle doors will lock when the brake pedal is applied and unlock when ignition is
OFF.
4. Speed
The vehicle doors will lock when speed is sensed and unlock when ignition is OFF.
1. Disabled
The OEM alarm will not be controlled by the interface upon remote start. No disarm or
arm command will be executed at the beginning or end of the sequence; it must be
controlled by the Remote Starter.
2. Safelock
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote
starter. It will unlock at the beginning of the sequence, and relock after start and
shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm
and rearm the vehicle in the remote start sequence, only when required. Smart OEM
Alarm Control will monitor the alarm and door lock status to detect if the disarm or
rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed.
Automatic Controlled Door Lock
8
Smart OEM Alarm Control
4
Defroster
5
Heated Seats/Defroster Temperature
Control
6
Heated Seats Temperature Level
7
RFTD Output Type
2
Unlock Driver Priority
3
Heated Seats
1
It is recommended to configure all the features and options listed below using the configuration tool found on the module
flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible
using the information on this page.
Page 8
Rev.: 20160201
Platform: DBALL2
Firmware:
CHRYSLER10
© 2016 Directed. All rights reserved.
Wire jump template
You have successfully completed the module programming sequence.
Once the configuration is completed, reconnect the module.
The LED turns solid green for 3 sec. then OFF.
Click on Submit Key2GO Request.
Remove the DBALL from the vehicle and reconnect it to your computer. The Directechs web site will
automatically recognize that you are moving onto the second phase of the programming sequence.
Solid
x3 sec.
Off
7
6
5