En v3.1 supplementary manual this supplementary manual explains mainly the functions that have been added or changed in cl5/cl3/ cl1 firmware v3.1. Use it in conjunction with the cl5/cl3/cl1 v3 owner's manual and reference manual..
Contents v3.1 supplementary manual 2 contents input channels .......................................................................... 3 added pan function (monaural input channels only) ............................................... 3 changing input signal processing when setting lr-mono (stereo ...
Input channels v3.1 supplementary manual 3 input channels added pan function (monaural input channels only) the pan setting for signals sent to the stereo bus enables you to select pan law settings. You can select one of the following: note the settings are also applied to the signals sent to the st...
Input channels v3.1 supplementary manual 4 you can also check the status of pan law settings in the window shown below. For channels where the mark is on, pan law is set to lr nominal. • to stereo/mono window (ch1-48, ch49-72/st in(cl5), ch49-64/st in(cl3), st in(cl1)) • overview window (stereo/mono...
I/o devices window v3.1 supplementary manual 5 i/o devices window added supported devices the rsio64-d is now supported. You can operate the rsio64-d in the i/o devices window. I/o devices window (i/o page) rsio64-d display 1 card name this indicates the names of the cards installed in slots 1 to 4....
I/o devices window v3.1 supplementary manual 6 indicates the word clock source status for the rsio64-d. *1 when flashing, dante word clock *3 input/output is used. *2 if you are using my8-aeb, set the ae rsvd switch for the card to rsvd. *3 if you make changes to the frequency of the dante word cloc...
I/o devices window v3.1 supplementary manual 7 added third-party equipment’s ha control function it is now possible to control supported third-party equipment’s head amps (ha) from the console. You can control ha by registering supported devices in the dante setup window. Note while in preview mode,...
Setup window v3.1 supplementary manual 8 setup window added functions for cascade connections the number of operations that can be linked when making cascade connections between cl series consoles has been increased. You can now select multiple operations. An attenuator is now built into the cascade...
Setup window v3.1 supplementary manual 9 cascade window (cascade in att page) 1 att knobs display the attenuator values (-96.0db to 0.0db) for cascade input signals. You can adjust these values using multifunction knobs 1 - 8 in the centralogic section or the [touch and turn] knob. Note you can use ...
Channel job v3.1 supplementary manual 10 channel job added parameters to recall safe function parameters that can be excluded from recall operations have been added. Recall safe mode window cascade in and cascade out have been added to the global recall safe field. Global recall safe window the foll...
Scene memory v3.1 supplementary manual 11 scene memory added parameters to global paste function cascade in and cascade out have been added as parameters that can be selected for the global paste function. Global paste window (patch/others page) the following parameters have been added. Added parame...
Save/load window v3.1 supplementary manual 12 save/load window added remount function to usb flash drives if usb flash drive is not mounted, the format button will become a usb remount button. Press this button to mount a usb flash drive. Use this button if a usb flash drive is not recognized after ...
Other functions v3.1 supplementary manual 13 other functions changed update procedure for name sub cpu firmware the procedure for updating the name sub cpu firmware for the cl console from a usb flash drive has been changed. If the following window is displayed, the console has entered the mode for ...
© 2015 yamaha corporation p ub lished 07/2015 ma-a0 man u al de v elopment department yamaha man u al li b rary http://www.Yamaha.Co.Jp/manual/ yamaha pro a u dio glo b al w e b site http://www.Yamahaproaudio.Com/.
