Yamaha YZF-R1 Assembly Instructions Manual

Manual is about: 2001

Summary of YZF-R1

  • Page 1

    Thank you for downloading the "yzf-r1" paper craft model. By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble an authentic-looking replica of the yzf-r1. Assembly instructions: fifteen a4-sized sheets. Paper craft: fourteen a4-sized sh...

  • Page 2: Note

    - 2 - note to begin item of caution *take care when using sharp or pointed objects or when using bladed cutting tools. Place a heavy sheet of paper under the paper you want to cut. *use glue and other adhesives only in well-ventilated areas. *when printing, use a slightly reduced font size as there ...

  • Page 3: Front Cowl

    - 3 - a- 1 a- 1 a- 2 a- 3 a- 5 a- 4 a- 6 a- 7 a- 8 a- 9 a- 10 first, assemble each component by following the working method and markings. Then, refer to the il- lustration and photos below to glue the parts together. Indication of working methods fold or curve adhere 1 assembling the front cowl ref...

  • Page 4: Steering

    - 4 - b- 1 b- 2 b- 3 b- 4 b- 7 b- 6 b- 5 b- 8 b- 9 b- 11 b- 10 b- 13 b- 12 b- 18 b- 14 b- 15 b- 16 b- 17 b- 18 fold the parts as shown above so that the dotted lines on the gluing surfaces are lined up before gluing each section. Reference photo be careful not to leave any glue on b-5, 8 and 9 when ...

  • Page 5: 3    Assembling The Frame

    - 5 - c- 1 c- 1 c- 3 c- 5 c- 4 c- 2 c- 7 c- 8 c- 11 c- 12 c- 9 c- 10 c- 15 c- 16 c- 17 c- 13 c- 14 c- 23 after assembling both frames a and b, glue the two on the gluing surface shown below. Gluing surface (to frame b) be sure to assemble in the right direction c- 6 fold the parts as shown above so ...

  • Page 6: Fuel Tank

    - 6 - d- 1 d- 2 d- 3 d- 4 d- 1 d- 2 reference photo first, assemble each component by following the working method and markings. Then, refer to the il- lustration and photos below to glue the parts together. Indication of working methods fold or curve adhere 4 assembling the fuel tank fuel tank shee...

  • Page 7: Engine

    E- 1 e- 2 e- 3 e- 4 e- 5 e- 6 e- 7 e- 8 e- 11 e- 14 e- 15 e- 12 e- 13 e- 16 e- 17 e- 18 e- 19 e- 20 e- 21 e- 22 e- 23 e- 24 e- 25 e- 26 engine sheet e, 26 parts in total - 7 - 5 assembling the engine e- 9 e- 10 reference photo first, assemble each component by following the working method and markin...

  • Page 8: Under Cowl

    - 8 - f- 1 f- 2 f- 3 f- 4 f- 5 f- 6 f- 7 f- 8 f- 9 f- 10 f- 11 f- 12 f- 13 f- 14 gluing area reference photo under cowl sheet f, 14 parts in total adhere 6 assembling the under cowl first, assemble each component by following the working method and markings. Then, refer to the il- lustration and pho...

  • Page 9: Exhaust

    - 9 - g- 17 g- 1 g- 2 g- 3 g- 4 g- 9 g- 10 g- 13 g- 14 g- 5 g- 6 g- 7 g- 8 g- 11 g- 12 g- 15 g- 16 g- 18 g- 19 g- 20 g- 21 g- 22 g- 23 g- 24 g- 25 g- 26 [exhaust a] after assembling both exhaust pipes a and b, glue the two on the gluing surface shown below. First, assemble each component by followin...

  • Page 10: Rear Arm

    - 10 - h- 2 h- 4 h- 5 h- 3 h- 6 h- 11 h- 7 h- 8 h- 9 h- 10 assembly instructions h- 1 reference photo first, assemble each component by following the working method and markings. Then, refer to the il- lustration and photos below to glue the parts together. Indication of working methods fold or curv...

  • Page 11: Seat Cowl

    - 11 - i- 1 i- 2 i- 3 i- 4 i- 5 i- 6 i- 7 i- 8 i- 9 i- 10 i- 11 i- 12 i- 13 i- 1 i- 2 reference photo seat cowl sheet i, 13 parts in total first, assemble each component by following the working method and markings. Then, refer to the il- lustration and photos below to glue the parts together. Indic...

  • Page 12: Front Tire

    J- 1 j- 2 j- 3 j- 4 j- 5 j- 6 l- 2 l- 1 l- 4 l- 5 l- 6 [front tire] insert the assembled wheel in the assembled tire before gluing them together. Front tire sheet j & l, 12 parts in total - 12 - l- 3 k- 1 k- 2 k- 3 k- 4 k- 5 k- 6 l- 9 l- 10 l- 11 l- 8 l- 7 l- 12 l- 13 gluing area assemble j-2 in the...

  • Page 13: 11   Finish

    Glue the assembled parts in numerical order through . - 13 - 11 finish assembly instruction detailed instructions for assembling the frame and the seat cowl gluing area apply glue in the back after inserting the frame in the seat cowl up to the red dotted lines, glue the two together from the inside...

  • Page 14

    - 14 - 12 assembled model and the list of parts please refer to the photo below when attaching each component. Right front g- 1 g- 2 g- 3 g- 4 g- 5 g- 6 g- 7 g- 8 g- 9 g- 10 g- 11 g- 12 g- 13 g- 14 g- 15 g- 16 g- 17 g- 18 g- 19 g- 20 g- 21 g- 22 g- 23 g- 24 g- 19 g- 20 g- 21 g- 22 g- 23 g- 24 j- 1 j...

  • Page 15

    - 15 - left rear e- 1 e- 2 e- 3 e- 4 e- 5 e- 6 e- 7 e- 8 e- 9 e- 10 e- 11 e- 12 e- 13 e- 14 e- 15 e- 16 e- 17 e- 18 e- 19 e- 20 e- 21 e- 22 e- 23 e- 24 e- 19 e- 20 e- 21 e- 22 e- 23 e- 24 k- 1 k- 2 k- 3 k- 4 k- 5 k- 6 k- 7 k- 8 k- 9 k- 10 k- 11 k- 12 e- 25 e- 26 f- 1 f- 2 f- 3 f- 4 f- 5 f- 6 f- 7 f-...