1. DL manuals
  2. Bulldog Security
  3. Car Alarm
  4. 1402
  5. Installation And Owner's Manual

Bulldog Security 1402 Installation And Owner's Manual

Other manuals for 1402: Owner's Manual
Manual is about: KEYLESS ENTRY AND ALARM SYSTEM

Summary of 1402

  • Page 1

    Contents keyless entry and alarm system • model 1402 installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:00 ...

  • Page 2

    System features system components 1 2 four-button extended control your car from an extended distance. Range remote control keyless entry remotely locks and unlocks your power door locks. Remote locking and remotely locks your power door locks when the ignition is turned on and unlocking with igniti...

  • Page 3

    Technical assistance should you need help. First check our website at www.Bulldogsecurity.Com/wires.Htm or call our toll-free tech support hotline monday through friday 9am-8pm and saturday 10am-4pm est at 800-878-8007. You must give the following information: •name •telephone number with area code ...

  • Page 4

    Making wiring connections 4. Insert the wire from the unit through the hole as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie ...

  • Page 5

    4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower w...

  • Page 6

    5 connecting the power and ground 1. Connect the red wire from the harness to a constant 12 volt supply or to the wire you ran from the positive battery post (if no constant 12 volt supply was found at the ignition switch harness). 2. Connect the black wire from the harness to a clean chassis ground...

  • Page 7

    6 connect the control module orange wire negative (-) out when armed to the optional starter disable relay (-) negative input. Pin 86 on spdt 30 amp relay or use part #pro1010 and relay #30-arb to connect “key side” and “starter side” of the cranking wire to the optional relay for starter disable. U...

  • Page 8

    7 the system. •to prevent water damage, the siren should not be mounted in a wheel well, directly behind the radiator grill or close to the ground. •mount the siren as far away from sources of heat, i.E. Exhaust manifold, turbo charger, etc. As possible. Tape, wrap or tube all wires. Run all wires t...

  • Page 9

    8 red (+) 12 volt constant black chassis ground brown (+) parking light output orange* (-) output when armed; starter disable, etc. Yellow (+) 12 volt ignition sense input ignition harness (or) fuse box blue* (+) lock or (-) unlock output 200ma max gray* (-) output to horn relay 200ma max (or) optic...

  • Page 10

    Operator programming instructions entering programming mode make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want to remain in programming mode. The only exception is when a different remote has been learned. The unit will exit the program...

  • Page 11

    10 a. Turn the ignition switch to the on or run position. B. Press and hold button #1 on the transmitter for approximately 10 seconds or until parking lights flash once. C. Press and release button #2 on the transmitter. The parking lights will flash twice and the led begins to flash. D. Press and r...

  • Page 12

    11 programming tables to enter operating programming mode a. Turn the ignition switch to the on or run position. B. Press and hold transmitter button #1 for approximately 10 seconds or until the parking lights flash once. C. Press one of the following buttons to go to the following tables: button fl...

  • Page 13

    How to use your remote transmitter 12 2 3.5 sec. Door lock pulse length 2 1 negative input activated 2 negative input deactivated 3 1 siren tone output 2 car horn output 4 1 positive door pin input 2 negative door pin input table five button flashes setting 2 1 delayed dome lights activated 2 delaye...

  • Page 14

    13 this feature is useful when having your vehicle valet parked, washed or serviced. While in valet mode, keyless entry and instant panic will still work; however, the alarm will not arm. Valet mode may also be programmed while the engine is running. Arming press transmitter button #1 to arm the sys...