Bulldog Security 1402 Installation And Owner's Manual - page 11
10
A. Turn the ignition switch to the on or run position.
B. Press and hold button #1 on the transmitter for approximately 10 seconds or until parking lights
flash once.
C. Press and release button #2 on the transmitter. The parking lights will flash
twice and the LED begins to flash.
D. Press and release button #3 on the transmitter. The parking lights will flash once. System is
now in silent arming mode.
E. Turn the ignition switch off. The parking lights will flash 3 times and the LED will stop flashing.
TO PROGRAM FULL TIME SILENT ARMING OFF
Repeat above procedure. In step D, the parking lights will flash twice instead of once.
TO PROGRAM PASSIVE ARMING ON
A. Make sure system is disarmed.
B. Turn the ignition switch to the on or run position.
C. Press and hold button #1 on the transmitter for approximately 1 0 seconds or until the parking
lights flash once.
D. Press and release button #3 on the transmitter. The parking lights will flash 3 times and the
LED will begin to flash.
E. Press and release button #1. The parking lights will flash once. Passive arming is now on.
F. You must now choose whether or not to have the system lock your doors automatically when it
fully arms itself in passive arming.
G. By pressing and releasing button #2, you can choose:
-1 Parking light flash for yes
-2 Parking light flashes for no
-If parking lights flash 3 times, go to step E
H. After these choices are made, you can exit programming passive arming on.
I. Turn the ignition switch to the off position. Parking lights will flash 3 times
and the LED will turn off.
TO PROGRAM PASSIVE ARMING OFF
A. Make sure system is disarmed.
B. Repeat above procedures A-E. In step E, the parking lights will flash twice instead of once.
C. Turn the ignition off. The parking lights will flash 3 times and the LED will turn off.
TO PROGRAM PASSIVE ARMING WITH OR WITHOUT DOOR LOCKS
A. Make sure system is disarmed.
B. Turn the ignition to the on or run position.
C. Press and hold button #1 on the transmitter for approximately 10 seconds or until the parking
lights flash once.
D. Press and release button #3. The parking lights will flash 3 times and the LED will begin to
flash.
E. Press and release button #2 until the desired option is selected:
-1 Parking light flash = Door lock in passive arming
-2 Parking light flashes = Doors won't lock in passive arming
-3 Parking light flashes = Passive arming is not turned on (To turn on passive
arming, refer to passive arming on in programming options)
F. Turn the ignition switch to the off position. The parking lights will flash 3 times and the
LED will stop flashing.
TO PROGRAM IGNITION CONTROLLED DOOR LOCKS ON/OFF
If you turned this feature on in programming options for keyless entry, then it is turned on for
the alarm feature. To turn this feature on and off, please make sure the system is disarmed and follow
the procedures for ignition controlled door locks in the keyless entry, section.
SYSTEM PROGRAMMING OPTIONS
To Teach The Unit A Factory Replacement Transmitter: NOTE: When used as an alarm, make sure system
is disarmed.
A. Turn the ignition switch to the on or run position.
B. Press and hold button #1 on the transmitter that came with the unit for approximately 10 seconds
or until the parking lights flash once.
C. Press and release button #2 on the transmitter that came with the unit. The parking lights will
flash twice and the LED starts to flash.
D. Press and release button #4 on the transmitter that came with the unit. The parking lights will
flash once.
E. Press any button on the new transmitter within 15 seconds and the parking lights will flash
once when the new transmitter is learned. It doesn't learn the new transmitter or no button is
pressed within 15 seconds, the parking lights will flash twice.
F. Turn the ignition switch to the off position. The parking lights will flash 3 times.
G. If the time expired or the new transmitter wasn't learned, please retry the procedure. If this
does not work the second time, please call our technical support staff.