- DL manuals
- Cabletron Systems
- Switch
- SmartSwitch 6000
- Overview And Setup Manual
Cabletron Systems SmartSwitch 6000 Overview And Setup Manual
Summary of SmartSwitch 6000
Page 1
6c105 smartswitch 6000 overview and setup guide 1 2 3 4 5 ps1 ps2 6c405 9032016-04.
Page 3: Notice
6c105 overview and setup guide i notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The har...
Page 4
Notice ii 6c105 overview and setup guide doc notice this digital apparatus does not exceed the class a limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the canadian department of communications. Le présent appareil numérique n’émet pas de bruit...
Page 5
Notice 6c105 overview and setup guide iii cabletron software program license 1. License. You have the right to use only the one (1) copy of the program provided in this package subject to the terms and conditions of this license agreement. You may not copy, reproduce or transmit any part of the prog...
Page 6
Notice iv 6c105 overview and setup guide declaration of conformity application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european rep...
Page 7: Contents
6c105 overview and setup guide v contents chapter 1 introduction 1.1 using this guide ......................................................................... 1-1 1.2 structure of this guide................................................................ 1-1 1.3 document conventions ..................
Page 8
Contents vi 6c105 overview and setup guide.
Page 9: Chapter 1
6c105 overview and setup guide 1-1 chapter 1 introduction welcome to the cabletron systems 6c105 smartswitch 6000 overview and setup guide . This guide explains how to set up and configure the cabletron systems 6c105 smartswitch 6000 chassis. 1.1 using this guide read through this guide completely t...
Page 10: 1.3
Chapter 1: introduction 1-2 6c105 overview and setup guide 1.3 document conventions throughout this guide the following symbols are used to call attention to important information. 1.4 using the 6c105 manual set other manuals have been developed for the interface modules that can be installed in the...
Page 11: 1.5
Getting help 6c105 overview and setup guide 1-3 1.5 getting help if you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact the cabletron systems global call center: before calling the cabletron systems global call ce...
Page 12: 1.6
Chapter 1: introduction 1-4 6c105 overview and setup guide 1.6 overview the cabletron systems 6c105 chassis design provides five 2.4-inch slots that can contain a variety of interface modules. The chassis supports redundant power supplies, lanview diagnostic leds, and is 19-inch rack mountable. All ...
Page 13: 1.7
Features 6c105 overview and setup guide 1-5 1.7 features redundant power supply modules the 6c105 supports two power supply modules which reside in the slots labeled ps1 and ps2. Each power supply module supports an ac input connector that allows each power supply to be connected to a separate ac po...
Page 14
Chapter 1: introduction 1-6 6c105 overview and setup guide auto-ranging power supplies the 6c105 power supply modules automatically adjust to the input voltage and frequency. No additional adjustments are necessary. Hot swapping to reduce network downtime, the power supply modules are also hot swapp...
Page 15: Chapter 2
6c105 overview and setup guide 2-1 chapter 2 installation requirements and specifications this chapter describes the following: • site guidelines that must be met before installing a 6c105 into a rack or cabinet • 6c105 configuration guidelines • operating specifications for the 6c105 enclosure and ...
Page 16: 2.2
Chapter 2: installation requirements and specifications 2-2 6c105 overview and setup guide 2.2 configuration guidelines the 6c105 has 5 slots that accept interface modules. The slots are numbered 1 to 5 beginning from the left. There are two additional slots located on the far right of the chassis t...
Page 17: 2.3.1
Operating specifications 6c105 overview and setup guide 2-3 2.3.1 physical specifications the physical specifications for the 6c105 chassis, 6c205-1, 6c205-2, 6c205-3 power supply modules and the 6c405 fan tray module are as follows: 6c105 chassis 6c205-1 power supply 6c205-2 power supply 6c205-3 po...
Page 18: 2.3.2
Chapter 2: installation requirements and specifications 2-4 6c105 overview and setup guide 2.3.2 power supply requirements the power supply requirements for the 6c205-1, 6c205-2 and 6c205-3 power supply modules are as follows: 6c205-1 ac power supply 6c205-2 dc power supply 6c205-3 ac power supply 2...
Page 19
Leds 6c105 overview and setup guide 2-5 figure 2-1 power supply leds table 2-1 power supply led states and their definitions led name color status pwr (power) green all outputs and input of the power supply are within regulation. Red any output or input of the specific power supply is out of regulat...
Page 20: 2.4.2
Chapter 2: installation requirements and specifications 2-6 6c105 overview and setup guide 2.4.2 fan tray led the following table describes the different states of the fan tray led and their definitions. Refer to figure 2-2 for the location of the fan tray led. Figure 2-2 fan tray led table 2-2 fan ...
Page 21: Chapter 3
6c105 overview and setup guide 3-1 chapter 3 6c105 setup this chapter contains instructions on setting up the cabletron systems 6c105 chassis. A phillips screwdriver is needed to install the unit in a 19-inch equipment rack, to install the cable management bar, to secure the power supply module(s) a...
Page 22: 3.2
Chapter 3: 6c105 setup 3-2 6c105 overview and setup guide 3.2 setting up the 6c105 the following sections describe the procedures that must be followed to complete the installation of the 6c105. 3.2.1 installation order once a suitable site has been chosen, the 6c105 can be installed. The chassis ca...
Page 23: 3.2.2
Setting up the 6c105 6c105 overview and setup guide 3-3 3.2.2 installing the cable management bar to install the cable management bar, proceed as follows: 1. Remove the cable management bar from the shipping box. Ensure that there are four screws inside the bag with the cable management bar. 2. Refe...
Page 24: 3.2.3
Chapter 3: 6c105 setup 3-4 6c105 overview and setup guide 3.2.3 rack mounting the 6c105 the 6c105 can be mounted in a standard 19-inch equipment rack. Two people may be required to lift the chassis into place. The chassis is secured with ten screws, five on each side. Using the screws provided with ...
Page 25: 3.2.4
Setting up the 6c105 6c105 overview and setup guide 3-5 3.2.4 attaching the electrostatic discharge wrist strap the electrostatic discharge (esd) wrist strap must be attached before handling the power supplies, fan tray, or modules for the 6c105. In addition, observe all precautions when handling th...
Page 26: 3.2.5
Chapter 3: 6c105 setup 3-6 6c105 overview and setup guide 3.2.5 installing a power supply module you must install at least one power supply in the 6c105 chassis. One power supply provides sufficient power for most module configurations but a second power supply can be installed to provide a redundan...
Page 27
Setting up the 6c105 6c105 overview and setup guide 3-7 4. Slide the power supply module into the slot labeled ps1 as follows: a. Hold the module by placing one hand on the handle located on the module front panel and using the other hand to support the body of the module. B. With the led at the top...
Page 28
Chapter 3: 6c105 setup 3-8 6c105 overview and setup guide figure 3-4 installing the power supply module(s) after installation of the power supply modules is completed the 6c105 is ready to be powered up; however, cabletron systems recommends that installation of all modules for the 6c105 be complete...
Page 29: 3.2.6
Setting up the 6c105 6c105 overview and setup guide 3-9 3.2.6 installing 6c105 interface modules the 6c105 interface modules can be installed in any of the 5 slots that are available. To install a module, proceed as follows: 1. Remove the blank panel covering the slot in which the interface module w...
Page 30
Chapter 3: 6c105 setup 3-10 6c105 overview and setup guide figure 3-5 installing a module 1 2 3 4 5 ps1 ps2 plastic locking tab slot number 2361-02 2159-01 circuit card card guides metal back-panel plastic locking tab backplane connector 1 2 14 13 com cpu 3 4 5 6 7 8 9 10 11 12 15 16 6e252-17 fast e...
Page 31: 3.3
Powering up a 6c105 with ac power supplies 6c105 overview and setup guide 3-11 3.3 powering up a 6c105 with ac power supplies to power up a 6c105 with ac power supply modules proceed as follows: 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the bottom...
Page 32
Chapter 3: 6c105 setup 3-12 6c105 overview and setup guide figure 3-6 power supply dc on/off switch and dc input power strip dc power supply requirement for each supply each dc power supply input requires either a 48 vdc or 60 vdc power source, rated at a minimum of 17 amps. Only qualified personnel...
Page 33: 3.4.1
Powering up a 6c105 with dc power supplies 6c105 overview and setup guide 3-13 installation requirement each dc power supply input requires either a 48 vdc or 60 vdc power source supplied by three 10 awg (american wire gauge) copper wires. These wires must be terminated with either ring or spade ter...
Page 34: 3.5
Chapter 3: 6c105 setup 3-14 6c105 overview and setup guide if you experience any problems during the installation of the 6c105, contact cabletron systems global call center for assistance. 3.5 removing and reinstalling the fan tray the 6c105 is equipped at the factory with a removable fan tray that ...
Page 35: 3.5.2
Removing and reinstalling the fan tray 6c105 overview and setup guide 3-15 figure 3-8 removing the fan tray 3.5.2 reinstalling the fan tray to reinstall the fan tray, refer to figure 3-9 and proceed as follows: 1. Locate the esd wrist strap shipped with the 6c105. Attach the esd wrist strap to your ...
Page 36
Chapter 3: 6c105 setup 3-16 6c105 overview and setup guide 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6c105. If there is any strong resistance, remove the fan tray and reinsert it. 5. Once the tray is in place, tighten the slotted screws with a screwd...
Page 37
Removing and reinstalling the fan tray 6c105 overview and setup guide 3-17 figure 3-9 reinstalling the fan tray slot guides slotted screws (2) 1 2 3 4 5 ps1 ps2 2016_08 6c405.
Page 38
Chapter 3: 6c105 setup 3-18 6c105 overview and setup guide.