Ferm FGG-2000N User Manual - page 7
S
Se
errv
viic
ce
e –
– n
no
otte
es
s o
on
n m
ma
aiin
ntte
en
na
an
nc
ce
e
F
Fiig
g..1
1
O
Oiill rre
ep
plla
ac
ce
em
me
en
ntt
• Warm up engine on level ground
• Remove filler cap (8)
• Open drain plug (9) and let oil drain
completely into a pan placed under the
engine.
• Check gaskets, replace if required. Refit
drain plug and refill engine with clean oil.
• Replace filler cap.
S
Sp
pa
arrk
k p
pllu
ug
g iin
ns
sp
pe
ec
cttiio
on
n
F
Fiig
g.. 3
3
• Disconnect the spark plug cap, and
remove any dirt from around the spark
plug area.
• Remove spark plug (17) with the plug
spanner supplied.
• Inspect the spark plug. It should be a tan
colour.
• Measure the gap (distance contact point)
with a suitable gauge. The gap should be
0,7 - 0,8 mm. Correct the gap, if necessary,
by carefully bending the side electrode.
• Replace the spark plug if the electrodes
are worn, or if the insulator is cracked or
chipped.
• Install the spark plug carefully, by hand, to
avoid cross-threading.
• Place the spark plug with correct torque:
20 Nm.
• Attach the spark plug cap.
E
Ex
xh
ha
au
us
stt s
sc
crre
ee
en
n
• Wait for exhaust to cool.
• Exhaust screen may be blocked up with
carbon deposits.
• Undo the screw cap and remove the
exhaust screen.
• Clean the screen with a wire brush and
refit.
• Replace exhaust screen if damaged.
A
Aiirr ffiilltte
err c
clle
ea
an
niin
ng
g
• Remove the air filter cover (16).
• Remove filter element and wash well in
solvent.
• Pour a small amount of oil onto the filter
element and gently squeeze out any
excess oil.
• Replace the filter element and air filter cover.
• Be sure the filter cover seals properly all
around.
Do not run the engine without the air
filter element in place.
Never place a wet filter (with solvent)
on the machine.
F
Fu
ue
ell tta
ap
p
• To remove the fuel tap filter, simply undo
the cup at the bottom of the fuel tank
• Use a small spanner to remove the tap
• Clean and wash out the filter and cup, and
replace.
T
TR
RO
OU
UB
BL
LE
ES
SH
HO
OO
OT
TIIN
NG
G
B
Ba
as
siic
c c
ch
he
ec
ck
ks
s
• Make sure you have plenty of fuel
• Make sure the fuel tap is on
• Make sure the engine-switch is on
• Make sure the oil level is correct
• The generator has an oil sensor. When the
oil level is too low, the generator will not be
able to start.
• Remove spark plug, connect spark plug
lead and earth it to the generator. Pull
starter cord gently and look for a spark. If
there is no spark, replace spark plug.
S
Sp
pa
arrk
k p
pllu
ug
g iis
s O
OK
K,, b
bu
utt e
en
ng
giin
ne
e s
sttiillll w
wo
on
n’’tt
s
stta
arrtt
• Check fuel tap filter is clean
• Check fuel line is clear
• Check carburetor is not clogged
E
En
ng
giin
ne
e w
wiillll n
no
ott s
stta
arrtt
• Clean or replace spark plug
• Check ignition system – if faulty, contact
your service centre
• Check compression – if low, contact your
service centre
• Check for loose cylinder head – tighten
bolts
• Check for damaged cylinder head gasket –
replace if necessary
Ferm
7
7
Dichiariamo, assumendo la piena
responsabilità di tale dichiarazione, che il
F
FG
GG
G--2
20
00
00
0N
N
è conforme alle seguenti normative ai relativi
documenti.
E
EN
N1
12
26
60
01
1,, E
EN
N5
55
50
01
14
4--1
1,, E
EN
N5
55
50
01
12
2,,
E
EN
N6
61
10
00
00
0--6
6--1
1
conforme alle direttive
9
98
8//3
37
7//E
EC
C,, 2
20
00
06
6//9
95
5//E
EC
C,, 2
20
00
04
4//1
10
08
8//E
EC
C,,
2
20
00
02
2//9
95
5//E
EC
C,, 2
20
00
02
2//9
96
6//E
EC
C
dal 01-01-2007
Z
ZW
WO
OL
LL
LE
E N
NL
L
J.A. Bakker - van Ingen
J. Lodewijk
CEO Ferm BV
Quality Manager
Ferm Global
La nostra politica è sempre volta a migliorare i
nostri prodotti . Prodotti soggetti a modifiche
senza preavviso.
F
Fe
errm
m B
BV
V •
• L
Liin
ng
ge
en
ns
sttrra
aa
att 6
6 •
• 8
80
02
28
8 P
PM
M
Z
Zw
wo
olllle
e •
• O
Olla
an
nd
da
am
m
CE
ı
DDIICCHHIIAARRAAZZIIO
ONNEE DDII CCO
ONNFFO
ORRM
MIITTÀÀ
((II))
4
42
2
Ferm