- DL manuals
- Ganz
- Security Camera
- ZC-PT Series
- Installation Manual
Ganz ZC-PT Series Installation Manual
Summary of ZC-PT Series
Page 2: Preface
Installation guide 1 preface the information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice this manual provides the installation information for indoor mini speed dom...
Page 3
Installation guide 2 this symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with directive 2002/96/ec. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment...
Page 4: Warnings and Cautions
Installation guide 3 warnings and cautions • handle the camera carefully do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. • installing electricity wiring carefully ask qualified personnel of electrical wiring for the installation. Ple...
Page 5
Installation guide 4 • never face the camera towards the sun do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged..
Page 6: Table of Contents
Installation guide 5 table of contents 1. Introduction ............................................................................................................................. 7 2. Standard package content.............................................................................................
Page 7
Installation guide 6 5.3 signal distribution unit .................................................................................................. 48 5.4 coaxial telemetry .......................................................................................................... 49 6. System integr...
Page 8: 1. Introduction
Installation guide 7 1. Introduction the mini speed dome camera is a new subcompact high speed dome camera designed to deliver superb performance and durability with an intelligent and stylish housing that is suitable in any security and surveillance installation. General operation requirements: a m...
Page 9: Standard Package Content
Installation guide 8 2. Standard package content before proceeding, please check the box contains the items listed here. If any item is missing, or if damage is evident, do not install or operate the product and contact your dealer for assistance. Analog dome camera package data cable for power supp...
Page 10
Installation guide 9 ip dome camera package dome camera data cable for power supply, video and audio (ac 24v or dc 12v) quick guide cd: operation manuals hard ceiling mount m3 screw, fixing plate.
Page 11: 3.1
Installation guide 10 3. Camera setups and cable connection before installing or connecting the dome camera, please refer to this section and complete preparation, switch setting and communication switch settings. 3.1 dome camera setups before connecting the dome camera to other devices of cctv syst...
Page 12: 3.1.2
Installation guide 11 the id and protocol numbers of an analog camera are set with a 10-bit and 6-bit dip switch respectively using binary system. For switch configuration details, please refer to appendix b: switch settings index table in mini speed dome camera’s user manual. 3.1.2 communication sw...
Page 13: 3.1.3
Installation guide 12 ip dome camera the ip dome camera’s communication switches are specified in the table below. Each switch’s default setting is shown as the figure below. Do not change the default setting, or some functions may not work properly. Communication switch sw 1 sw 2 audio setting sw 3...
Page 14: 3.1.4
Installation guide 13 3.1.4 camera control protocol setup (analog model) define the protocol you are going to use basing on the devices of your surveillance system. Generally, use one protocol even the devices are provided from different manufacturers. Use the switch to set your camera control proto...
Page 15: 3.2
Installation guide 14 3.2 cable definition and requirements for operation, the dome camera requires the video cable to carry the video signals to the remote viewing site, power cable to power the dome camera and rs-485 data cable to carry commands from the control device. 3.2.1 cable requirements fo...
Page 16: 3.2.2
Installation guide 15 3.2.2 22-pin connector definition the analog and ip dome cameras’ data cables are illustrated as follows. Analog dome camera dc 12v data cable ac 24v data cable note: be careful not to pull the cables improperly during installation. Additionally, it is suggested to fasten the c...
Page 17: 3.2.3
Installation guide 16 ip dome camera the ip dome camera’s data cables are illustrated as shown below. Ac 24v data cable dc 12v data cable 3.2.3 22-pin connector definition with the 22-pin connector, installers can simply connect the power, video and rs-485 cables to the dome camera at once. Particul...
Page 18
Installation guide 17 analog dome camera the analog dome camera’s 22-pin connector definition is listed as below. Pin definition cable pin definition cable 1 ac 24-1/dc (＋) 20awg/18awg 12 alm-1 2 alm nc 13 alm-3 3 ac 24-2/dc (－) 20awg/18awg 14 alm-2 4 alm no 15 alm-4 5 fg 20awg/18awg 16 alm-5 6 alm ...
Page 19: 3.2.4
Installation guide 18 3.2.4 rs-485 connector (analog model) rs-485 is the interface that communicates the dome camera and its control device. Please connect the control keyboard to the speed dome camera through the terminal block. The recommended cables for rs-485 communication are cat 5 cables; max...
Page 20: 3.2.6
Installation guide 19 insert the terminal into the pin holes on the connector housing, with the hook outward, as indicated in the figure. To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Connect the 22-pin connector to its mating port on ...
Page 21: 4. Dome
Installation guide 20 4. Dome installation in the following sections, various dome camera installation accessories, installation methods and installation procedures will be described in detail. The next section will provide the dome camera’s dimension for your reference before installation. 4.1 dome...
Page 22: 4.2 Optional
Installation guide 21 4.2 optional accessories indoor dome camera accessories power adapter 77h07-a1015 (input: 100~115vac/output: 24vac 36va 77h07-a2015 (input: 220~230vac/output: 24vac 36va) note: when wiring, make sure the ground wire inserted into the mid-pin of the terminal block mounting acces...
Page 23
Installation guide 22 compact pendant mount white; 184×104×115.2 mm (7.24×4.09×4.54 inches); 0.6 kg (1.2 lbs). Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and m8*12 screw×1. Straight tube white, iron, height: 250/500 mm (9.8/19.7 inches) ,diameter: 50 mm (2 inches) 1 kg...
Page 24
Installation guide 23 corner standard mounting plate white, 222×204×117 mm (8.7×8×4.6 inches); 2 kg (4.4 lbs); supplied with washer-8×4, spring washer×4, m8*16 screw×4, m8 nut×4. Corner thin box mounting white/ivory, 300×164×222 mm (11.8×6.5×8.7 inches); 3 kg (6.7 lbs); supplied with washer×4, m8*16...
Page 25
Installation guide 24 pole thin box mounting white/ivory; 291×136×242 mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs); supplied with m8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Pole wide box mounting white/ivory, 270×166×155 mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs); supplied wit...
Page 26
Installation guide 25 pole thin direct mounting white/ivory, 232×136×60 mm (9.1×5.4×2.4 inches); diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs); supplied with stainless steel straps×4, m8*16 screw×4, washer×4. Pole wide direct mounting white/ivory, 270×170×60 mm (10.6×6.7×2.4 inches); diame...
Page 27
Installation guide 26 other application accessories repeater/converter d77r1: rs-485/rs-422 repeater d77r2: rs-232 between rs-485/rs-422 d77r3: bi-phase to rs-485/rs-422 d77r1 d77r2 d77r3 connector box (indoor application) recommended for wiring indoor dome alarm cables. White color. 92×42 mm (3.7×1...
Page 28: 4.3 Ceiling
Installation guide 27 4.3 ceiling mount the dome camera can be mounted to the concrete ceiling with the supplied hard ceiling mount and optional accessory: straight tube. 4.3.1 hard ceiling mount the indoor dome camera can be mounted to the concrete ceiling with the supplied hard ceiling mount. The ...
Page 29
Installation guide 28 step 3 drill on the four marked positions. Step 4 fix the hard ceiling mount to the ceiling using the self-tapping screws as shown in the figure. Step 5 thread the data cable and/or ethernet cable through the center hole of the mount and connect the cable to the connector on th...
Page 30
Installation guide 29 step 7 tighten the fixing screw, as marked in the figure, to fix the dome camera. Step 8 replace the dome camera’s optical cover if it is removed previously. The hard ceiling installation is complete..
Page 31: 4.3.2 Straight
Installation guide 30 4.3.2 straight tube the straight tube is available in different length: 25 cm and 30 cm. Items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • straight tube and equipped items (optional accessory) • indoor mount adapter (optional accessory) • s...
Page 32
Installation guide 31 7) attach the dome camera to the indoor mount adapter, aligning the adjustable screw of the plastic fixing plate (see the left diagram below) with the mating screw hole (see the right diagram below) on the indoor mount adapter, and screw them tightly. Ceiling mount: straight tu...
Page 33: 4.4 Wall
Installation guide 32 4.4 wall mount the dome camera can be mounted on the wall with compact pendent mount, standard pendent mount and wall box. Please follow the installation instructions below for mounting the dome camera via different ways. 4.4.1 compact pendent mount items needed: • dome camera ...
Page 34
Installation guide 33 note: please block the cable entry hole with the supplied sponge to avoid insects entering the pendant mount. The sponge can be placed in two ways as shown in the illustrations below. 4) thread the cable(s) through the indoor mount adapter and join the indoor mount adapter to t...
Page 35: 4.4.2
Installation guide 34 4.4.2 standard pendent mount items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard pendent mount and equipped items (optional accessory) • indoor mount adapter (optional accessory) • screws and screw anchors for fixing the standard pen...
Page 36
Installation guide 35 wall mounting: standard pendent mount + indoor mount adapter.
Page 37: 4.4.3
Installation guide 36 4.4.3 wall box mounting items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard/compact pendent mount and equipped items (optional accessory) • wall box mounting (optional accessory) • indoor mount adapter (optional accessory) • screws a...
Page 38
Installation guide 37 wall box mounting: wall box mounting + standard/compact pendent mount + indoor mount adapter.
Page 39: 4.5 Corner
Installation guide 38 4.5 corner mount 4.5.1 corner standard mounting plate/corner plate mini items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard/compact pendent mount and equipped items (optional accessory) • corner standard mounting plate/corner plate m...
Page 40
Installation guide 39 6) attach the dome camera to the indoor mount adapter, aligning the adjustable screw of the plastic fixing plate with the mating screw hole on the indoor mount adapter, and screw them tightly. See section 4.3.2 straight tube for illustrations. Corner wall mounting: corner stand...
Page 41: 4.5.2
Installation guide 40 4.5.2 corner thin/wide box mounting items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard/compact pendent mount and equipped items (optional accessory) • corner thin/wide box (optional accessory) • indoor mount adapter (optional access...
Page 42
Installation guide 41 corner box mounting: corner thin/wide box + standard/compact pendent mount + indoor mount adapter.
Page 43: 4.6 Pole
Installation guide 42 4.6 pole mount 4.6.1 pole thin/wide direct mounting items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard/compact pendent mount and equipped items (optional accessory) • pole thin/wide direct mounting (optional accessory) • indoor moun...
Page 44
Installation guide 43 6) attach the dome camera to the indoor mount adapter, aligning the adjustable screw of the plastic fixing plate with the mating screw hole on the indoor mount adapter, and screw them tightly. See section 4.3.2 straight tube for illustrations. Pole direct mounting: pole thin/wi...
Page 45: 4.6.2
Installation guide 44 4.6.2 pole thin/wide box mounting items needed: • dome camera • data cable (supplied) • ethernet cable (ip dome camera) • standard/compact pendent mount and equipped items (optional accessory) • pole thin/wide box mounting (optional accessory) • indoor mount adapter (optional a...
Page 46
Installation guide 45 pole box mounting: pole thin/wide box + standard/compact pendent mount + indoor mount adapter.
Page 47: 5. System
Installation guide 46 5. System expansion 5.1 connecting with connector box (indoor) ideally being used in indoor installation circumstances, a connector box provides easy wiring and well organized connection between alarms, cameras and other devices, for easy installation. To connect the connector ...
Page 48: 5.2
Installation guide 47 5.2 data formats transforming to integrate other surveillance devices with the speed dome cameras, we provide three kinds of converter/repeater to transform the communication formats between devices. If a converter/repeater is used, the total network distance of the surveillanc...
Page 49: 5.3
Installation guide 48 5.3 signal distribution unit the rs-485 signal distribution unit (sdu) is designed to relay control codes to speed dome cameras. It is capable of communicating with cameras up to 1.0 kilometers away. Additionally, the sdu can be installed in either “star” or “daisy chain” confi...
Page 50: 5.4 Coaxial
Installation guide 49 5.4 coaxial telemetry the coaxial telemetry is a low-cost solution to long distance connection between dome cameras and controlling devices (e.G. Dvr and keyboard). It simplifies the work of wiring by transmitting video and rs-485 control signals via one bnc line, so that to br...
Page 51: 6. System
Installation guide 50 6. System integration the dome camera is allowed to be integrated into other suppliers' surveillance systems with large set of built-in protocols. Refer to the following sections for more information. 6.1 using pelco keyboard the speed dome camera can be controlled through a pe...
Page 52: 6.2 Using
Installation guide 51 cable definition (d protocol keyboard to ptz camera) fo r sp e e d do m e fo r d pro toc ol ke yb oa rd tx- tx+ gnd rx- rx+ 1 2 3 4 5 6 tx - tx+ gnd rx- rx+ 1 2 3 4 5 6 gnd 6.2 using philips allegiant keyboard the dome cameras can be integrated into philips allegiant systems th...
Page 53
Installation guide 52 appendix a: technical specification items indoor mini ptz camera camera ccd sensor 1/4" exview ccd optical zoom 12x digital zoom 1× ~ 12× variable ntsc 380k effective pixels pal 440k horizontal resolution 540 tvl scanning system ntsc / pal synchronization internal / line lock v...
Page 54
Installation guide 53 motion detection on / off wide dynamic range on / off day/night: ir cut filter on / off image freeze on / off image inverse on / off 2d on / off noise reduction 3d on / off alarm input 8 alarm output 1 alarm reaction preset, sequence, auto pan, cruise general environment indoor...