Installation instruc- tions rfid 13.56 mhz interface board for easycoder f2 and f4 printers.
Information in this manual is subject to change without prior notice and does not represent a commitment on the part of intermec printer ab. © copyright intermec printer ab, 2002. All rights reserved. Published in sweden. Easycoder and fingerprint are registered trademarks of intermec technologies c...
1 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 1 description introduction rfid tag rfe sy st em s ww w.I ds ys .C o.U k sy st em s ww w.I ds ys .C o.U k antenna information reader with transceiver system & application hardware & software write t...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 2 chapter 1 description the rfid 13.56 mhz interface board is an optional device for easycoder f2 or easycoder f4, that provides these printers with two extra interfaces, "uart2:" and "uart3:". The printer mu...
3 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 1 description rfid media recom- mendations because the rfid tag is a part of a system consisting of the printer, the tag, the media in which the tag is fi tted, and the reader, all applications shou...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 4 chapter 1 description declaration of conformity we, intermec printer ab idrottsvägen 10 box 123 s-431 22 mölndal sweden declare under our sole responsibility 1 , that the product easycoder f2/f4 rfid 13.56 ...
5 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 2 fitting the interface board #t20 torx screws (3 places) field installation generally, the illustrations show an easycoder f4 printer. However, the same principles applies to easycoder f2 printers....
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 6 chapter 2 field installation #t10 torx screw cover plate #t10 torx screw • remove the two #t10 torx screws that hold the interface cover plate on the printer’s rear plate. Remove the cover plate. • save the...
7 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 2 field installation fitting the interface board, cont. P35 ic305 p32 ic304 p33 p81 1-971615-00.P01 c7 r12 r15 r14 r13 r9 r8 r3 r2 r1 jp1 ic7 ic6 ic5 ic2 ic1 c15 c14 c13 c12 c11 c6 rp1 c5 c4 c3 c2 p...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 8 chapter 2 field installation the shape of the antenna differs between easycoder f2 and easycoder f4. The antenna is fi tted inside the lower media guide. To be able to fi t it, you must remove the tear bar,...
9 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 2 field installation fitting the antenna, cont. • easycoder f4 only: from the electronics compartment, disengage the snap-lock that holds the cable guard and pull it out along the shaft. • pull out ...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 10 chapter 2 field installation • route the cable through the same slot in the center section as the lss cable. • fit back the media guide assy and grounding spring using the three #t20 torx screws while pull...
11 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 2 field installation • put back the cover over the electronics compartment. • connect the power cord. • now you have one new interface connector on the printer’s rear plate in addition to the stand...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 12 chapter 3 1-971615-00.P01 c7 r12 r15 r14 r13 r9 r8 r3 r2 r1 jp1 ic7 ic6 ic5 ic2 ic1 c15 c14 c13 c12 c11 c6 rp1 c5 c4 c3 c2 p5 p6 c1 c10 c16 d1 f1 f2 f3 f4 f5 f6 f7 f8 f9 f10 f11 f12 f13 f14 ic3 ic4 ic18 jp...
13 rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions chapter 3 serial port confi guration "uart2:" 1-971615-00.P01 c7 r12 r15 r14 r13 r9 r8 r3 r2 r1 jp1 ic7 ic6 ic5 ic2 ic1 c15 c14 c13 c12 c11 c6 rp1 c5 c4 c3 c2 p5 p6 c1 c10 c16 d1 f1 f2 f3 f4 f5 f6 f7 f8 f9...
Rfid 13.56 mhz interface board for easycoder f2 and f4 printers – installation instructions 14 chapter 3 serial port confi guration "uart2:" 1-971615-00.P01 c7 r12 r15 r14 r13 r9 r8 r3 r2 r1 jp1 ic7 ic6 ic5 ic2 ic1 c15 c14 c13 c12 c11 c6 rp1 c5 c4 c3 c2 p5 p6 c1 c10 c16 d1 f1 f2 f3 f4 f5 f6 f7 f8 f9...
Intermec printer ab idrottsvägen 10, p.O. Box 123 s-431 22 mölndal, sweden tel +46 31 869500 fax +46 31 869595 www.Intermec.Com *1-960495-01* rfid 13.56 mhz interface board for easycoder f2 and f4 printers, installation instructions *1-960495-01*.