Kuppersbusch EKV 6500 Instruction Manual - page 12
Changing coffee temperature
To change coffee temperature, proceed as follows:
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "TEMPERATURE" is displayed.
•
Press the OK icon (C12).
•
Press the icons (C8) and (C11) to select the required coffee tem-
perature from low, medium and high.
•
Press the OK button (C12) to confirm the temperature selected.
•
Press the ESC icon (C9) to exit the menu.
Setting water hardness
The descale message is displayed after the appliance has been operated
for a factory set period of time calculated on the basis of the maximum
quantity of limescale which may be contained in the water used.
The operating period can be extended if required, making descaling less
frequent by programming the machine on the basis of the real lime content
in the water used.
Proceed as follows:
•
remove the "Total Hardness Test" strip (attached to page 2) from its
packaging then dip it fully in the water for a few seconds,
Then remove and wait about 30 seconds (until it changes colour and
forms red squares).
•
turn the appliance on by pressing the On/stand-by button (A21).
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "WATER HARDNESS" is displayed.
•
Press the OK icon (C12).
•
Press the icons (C8) and (C11) until the number coincides with
the number of red squares on the test strip (for example, if there are 3
red squares on the test strip, select the message "WATER HARDNESS
3" .
•
Press the OK icon (C12) to confirm.
The coffee maker is now programmed to provide the descale warning
when actually necessary.
Programming coffee
For instructions on programming coffee, see the "CHANGING THE QUAN-
TITY OF COFFEE IN THE CUP" section.
Programming cappuccino
For instructions on programming cappuccino, see the "CHANGING THE
QUANTITY OF MILK AND COFFEE FOR CAPPUCCINO" section.
Programming water
For instructions, see the "CHANGING THE QUANTITY OF HOT WATER" sec-
tion.
Descaling
Important! Descaler contains acids. Respect the safety warnings pro-
vided by the manufacturer and given on the descaler pack.
N.B.! Use the descaler recommended by the manufacturer only. Use
of other descalers invalidates the guarantee. Failure to descale the appliance
as described also invalidates the guarantee.
Important! Before descaling, make sure the water softener filter has
been removed.
When "PLEASE DESCALE !" is displayed, the machine requires descaling.
Proceed as follows:
•
Make sure the machine is ready.
•
Attach the hot water spout (B7) to the nozzle (A8).
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "DESCALE" is displayed.
•
Press the OK icon (C12) and the appliance displays "DESCALE PLEASE
CONFIRM".
•
Press the OK icon (C12). The message "ADD DESCALER PLEASE CON-
FIRM" is displayed.
•
Empty the tank of water, pour the contents of the descaler bottle into the
tank respecting the instructions given on the descaler pack, then add
water up to the MAX level marked on the water tank.
Position a container with a capacity of about 2 litres under the hot water
spout.
•
Press the OK icon (C12). Descaler flows out of the hot water spout into
the container below.
The appliance displays: "DESCALING".
•
The descale programme automatically performs a series of deliveries
and pauses.
•
After about 30 minutes "DESCALE COMPLETE PLEASE CONFIRM" is
displayed.
•
Press the OK icon (C12). "RINSING PLEASE CONFIRM" is displayed.
•
Empty the water tank, rinse to eliminate descaler residues, then fill with
clean water.
•
Replace the tank."RINSING PLEASE CONFIRM" is displayed.
•
Press the OK icon (C12) again. Hot water flows out of the spout into the
container below and "RINSING" is displayed.
•
Wait until "RINSING COMPLETE PLEASE CONFIRM" is displayed.
•
Press the OK icon (C12). “DESCALE COMPLETE” and "FILL TANK" is di-
splayed. Fill the tank again with clean water.
•
The descale programme is now terminated and the appliance is ready
to make coffee again.
NOTE: If descaling is interrupted before completion, the process must
be begun again from the beginning.
Important! FAILURE TO DESCALE THE APPLIANCE REGULARLY
INVALIDATES THE GUARANTEE.
Resetting default values (reset)
If you change the original values, the default values can be reset as follows:
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "RESET TO DEFAULT" is displayed.
•
Press the OK icon (C12) and the appliance displays "RESET TO DE-
FAULT PLEASE CONFIRM".
•
press the OK button (C12) to reset the default values.
Statistics
This displays statistics relating to the machine.
To display, proceed as follows:
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "STATISTICS" is displayed.
•
Press the OK icon (C12).
•
Press the icons (C8) and (C11) to verify:
-
How many coffees and cappuccinos have been made.
-
How many times the machine has been descaled.
-
The total number of litres of water delivered.
•
Press the ESC icon (C9) once to exit the menu.
Buzzer
This activates or deactivates the buzzer emitted by the machine each time
an icon is pressed or an accessory is inserted/removed.
N.B.! The buzzer is active by default.
•
Press the M icon (C10) to enter the menu and then the icons (C8)
and (C11) until "BUZZER" is displayed.
•
Press the OK icon (C12). "BUZZER PLEASE CONFIRM" is displayed.
•
Press the ESC icon (C9) to disable or the OK icon (C12) to enable the
buzzer.
•
Press the ESC icon (C9) to exit the menu.
Water filter
For instructions on the water softener filter, see the section "INSTALLING THE
FILTER".
16