Kuppersbusch EKV 6500 Instruction Manual - page 9
Important! The grinding adjustment knob must only be turned
when the coffee mill is in operation.
For slower delivery and creamier coffee, turn one
click anticlockwise (finer pre-ground coffee).
For faster delivery (not a drop at a time), turn one
click clockwise (coarser pre-ground coffee).
MAKING COFFEE USING PRE-GROUND
COFFEE
•
Press the icon (C7) (fig. 8) to select the pre-ground coffee fun-
ction.
•
Extract the machine by pulling it outwards using the handles (fig. 7).
•
Lift the central lid, place one measure of pre-ground coffee in the fun-
nel (fig. 19), push the appliance in then proceed as described in the
section "Making coffee using coffee beans".
N.B.: You can make just one coffee at a time by pressing the icon
(C2).
•
After using the machine with pre-ground coffee, to go back to making
coffee using beans, deactivate the pre-ground coffee function by pres-
sing the icon (C7).
NOTE 1: Never introduce pre-ground coffee when the machine is off or it
could spread through the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the appliance will not
make the coffee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coffee for espresso coffee machines
into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used and the fun-
nel clogs, push the coffee down with a knife (fig. 21) then remove and clean
the brewing unit and machine as described in the "Cleaning the brewing
unit" section.
DELIVERING HOT WATER
•
Always make sure the appliance is ready.
•
Make sure the hot water spout is in place (fig. 5).
•
Position a container under the spout (fig. 6).
•
Press the icon (C6) (fig. 20).
The appliance displays: "HOT WATER PRESS OK".
•
Press the OK icon (C12) again and hot water is delivered from the water
spout into the container underneath.
You should not deliver hot water for more than 2 minutes at a time.
•
To interrupt, press the icon (C6) or the ESC icon (C9).
The appliance stops delivery once the set quantity is reached.
CHANGING THE QUANTITY OF HOT
WATER
The machine is set by default to automatically delivery 150 ml of hot water.
To change these quantities, proceed as follows:
•
Place a container underneath the water spout (fig. 6).
•
Press the M icon (C10) to enter the menu (fig. 15) or press the
icons (C8) and (C11) (fig. 2) until "PROGRAM HOT WATER" is displa-
yed.
•
Press the OK icon (C12) to confirm.
•
Select the required quantity of water by pressing the icons (C8)
and (C11).
The progress bar shows the quantity of water selected.
•
Press the OK icon (C12) to confirm or the ESC icon (C9) (fig. 18) to can-
cel the operation.
•
Press the ESC icon (C9) to exit the menu.
•
The appliance is now reprogrammed with the new settings and is ready.
MAKING CAPPUCCINO
N.B.: Set the quantity of coffee you want to use to make the cap-
puccino in the "Program cappuccino" function in the menu.
•
Select the taste of the coffee you want to use to make the cappuccino
by pressing the icon (C7) (fig. 8).
•
Remove the lid of the milk container.
•
Fill the container with about 100 grams of milk for each cappuccino to
be prepared (fig. 23). Never exceed the MAX level (corresponding to
about 750 ml) marked on the jug.
You should ideally use skimmed or semi-skimmed milk at refrigerator
temperature (about 5°C).
•
Make sure the intake tube is correctly inserted in the rubber washer
(fig. 24) then replace the milk container lid.
•
Position the frothed milk regulator (B1) between the words CAPPUC-
CINO and CAFFELATTE printed on the milk container lid.
The quality of froth can be adjusted by moving the frothed milk regu-
lator towards the word CAFFELATTE for a denser froth.
Moving it towards the word CAPPUCCINO obtains a less dense froth.
•
Remove the hot water spout and attach the milk container to the noz-
zle (fig. 25).
•
Position the milk tube as shown in fig. 26 and then place a sufficiently
large cup under the coffee and milk spouts.
•
Press the icon (C13). "CAPPUCCINO..." is displayed and after a few
seconds, frothed milk flows out of the milk spout into the cup below.
(Delivery stops automatically).
•
The appliance delivers the coffee.
•
The cappuccino is now ready. Sweeten to taste and, if desired, sprin-
kle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or coffee can
be interrupted by pressing the icon (C13).
NOTE 2: If the milk in the container finishes while delivering frothed milk,
remove the container and add milk. Then re-attach it and press the icon
(C13) to request cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the milk frother,
always clean the circuits in the milk container lid after making cappuccino.
"PRESS CLEAN!" flashes on the display.
•
Place a recipient under the milk spout (fig. 26).
•
Press the CLEAN button on the lid (B3) and hold down for at least 8 se-
conds (fig. 26) to start the cleaning function. The appliance displays
the message "CLEANING" above a progressive bar.
You should not release the CLEAN button until the bar is complete in-
dicating that cleaning is concluded.
When the CLEAN button is released, the function stops.
After cleaning, remove the milk container and place in the refrigerator.
The milk should not be left out of the refrigerator for more than 15 mi-
nutes.
NOTE 4: To change the quantity of coffee or frothed milk the appliance de-
livers automatically into the cup, proceed as described in the section "Chan-
ging the quantity of milk and coffee for cappuccino".
CHANGING THE QUANTITY OF MILK AND
COFFEE FOR CAPPUCCINO
The appliance is set by default to automatically deliver a standard cappuc-
cino.
To change these quantities, proceed as follows:
"Less dense"
froth
NO froth
"Denser" froth
frothed milk
regulator
13