Kuppersbusch EKV 6500 Instruction Manual - page 8
message "HEATING UP... PLEASE WAIT" is displayed.
When heating is complete, the message changes to "RINSING";
The appliance is at temperature when the message "MEDIUM CUP NOR-
MAL TASTE" is displayed.
If no icon is pressed within about 2 minutes, the time (if set, see the "Set-
ting the clock" section) is displayed.
If the time has not been set, the appliance displays the last functions set.
When any icon is pressed, "MEDIUM CUP NORMAL TASTE" is displayed
again.
The appliance is ready to make coffee again.
MAKING COFFEE USING COFFEE BEANS
1. The appliance is preset to make coffee with a normal taste.
You can also choose coffee with an extra-mild, mild, standard, strong
or extra-strong taste. There is also a pre-ground coffee option.
To choose the required taste, press more times the icon (C7) (fig.
8).
The required coffee taste is displayed.
2. Place 1 cup under the spouts to make 1 coffee (fig. 9) or 2 cups for 2
coffees (fig. 9). Lower the spouts as near as possible to the cup for a
creamier coffee (fig. 10).
3. Press the icon (C4) (fig. 11) to select the type of coffee: espresso,
small cup, medium cup, large cup, mug.
Press the icon (C2) (fig. 12) if you want to make a coffee and the
icon (C3) (fig. 13) if you want to make 2 coffees.
To change the quantity of coffee the appliance delivers automatically
into the cup, proceed as described in the following section.
The appliance now grinds the beans and starts delivering the coffee
into the cup.
Once the set amount of coffee has been delivered, the machine stops
delivery automatically and expels the exhausted waste coffee into the
waste coffee container.
4. After a few seconds, the appliance is ready for use again.
5. To turn the appliance off, press the On/stand-by button (A21) (fig. 1).
(Before going off, the appliance performs an automatic rinse cycle. Take
care to avoid scalds).
NOTE 1: If the coffee is delivered a drop at a time or not at all, see the "Ad-
justing the coffee mill" section.
NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory,
see the "Adjusting the coffee mill" section.
NOTE 3: Tips for a hotter coffee:
•
When you turn the appliance on, if you want to make a short coffee
(less than 60 cc), rinse the cups with hot water to preheat the cups.
•
If more than 2/3 minutes have passed since the last coffee was made,
before requesting another coffee, you must preheat the infuser by pres-
sing the button (C5).
Deliver the water into the underlying drip tray or alternatively use this
water to fill (and then empty) the cup to be used for the coffee, so as
to preheat it.
•
Unless preheated, do not use excessively thick cups as they will ab-
sorb too much heat.
•
Preheat the cups by rinsing them with hot water.
NOTE 4: While the appliance is making coffee, delivery can be interrupted
at any moment by pressing the previously selected icons (C2) or
(C3).
NOTE 5: As soon as delivery is finished, to increase the quantity of coffee
in the cup, just keep pressing the previously selected icon within 3 seconds
after delivery has finished.
NOTE 6: When the appliance displays "FILL TANK", fill the tank with water
or the appliance will not deliver coffee.
(It is normal for there to be a little water left in the tank).
NOTE 7: After about 14 single (or 7 double) coffees, the appliance displays
"EMPTY WASTE COFFEE CONTAINER".
To clean, open the service door on the front of the appliance by pulling the
spout (fig. 16), extract the drip tray (fig. 17) and clean.
When cleaning, always extract the drip tray completely.
Important! When extracting the drip tray, the waste coffee contai-
ner MUST always be emptied. If this is not done, the machine may be clog-
ged.
NOTE 8: Never extract the water tank while the machine is delivering cof-
fee.
If it is removed, it will not be possible to make the coffee and the appliance
will display "GROUND TOO FINE ADJUST MILL and INSERT WATER SPOUT
AND PRESS OK".
To use the appliance again, insert the hot water spout (fig. 5) if not already
in position, then press the OK icon (C12) and deliver water from the spout
for a few seconds.
N.B.: The coffee maker may request the operation to be repeated a
number of times until the air is completely elminated from the hydraulic
circuit.
N.B.: if this operation is not performed correctly or if the machine
is turned off, the basic modes may be displayed, although the problem is
in fact still present.
CHANGING THE QUANTITY OF COFFEE IN
THE CUP
The appliance is set by default to automatically make the following types of
coffee:
•
espresso
•
small cup
•
medium cup
•
large cup
•
mug
To change the quantity, proceed as follows:
•
Press the M icon (C10) to enter the menu (fig. 15). Press the icons
(C8) and (C11) (fig. 2) until "PROGRAM COFFEE" is displayed.
•
Press the OK icon (C12). The message "PROGRAM COFFEE ESPRESSO"
is displayed.
•
Select the type of coffee you want to change by pressing the icons
(C8) and (C11).
•
Press the OK icon (C12) to confirm the type of coffee you want to make.
•
Use the icons (C8) and (C11) to change the quantity of coffee.
The progress bar shows the quantity of coffee selected.
•
Press the OK icon (C12) again to confirm (or the ESC icon (C9) (fig. 18)
to cancel the operation).
•
Press the ESC icon (C9) to exit the menu.
The appliance is now reprogrammed with the new settings and is ready.
ADJUSTING THE COFFEE MILL
The coffee mill is preset in the factory and should not require adjusting.
However, if after making the first few coffees you find that delivery is either
too fast or too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment knob (fig. 14).
12