Leggett & Platt Designer Series Owner's Manual - page 6
Designer Series
™
99301294
6
ACOUSTICS
LIFTING/LOWERING MECHANISMS
The lift/lower feature will emit a minimal
humming sound during operation. This is
normal.
During operation, the lift arm wheels make
contact with the platform support of the base.
This applies slight tension on the moving
components and resonance is reduced to a
minimum level. If excessive noise or vibration
is experienced, reverse the movement action
(up or down) of the base with the hand control.
This should realign the base’s activating
mechanisms to the proper operational position.
MASSAGE OPERATION
The massage feature will emit a minimal tone
during operation. This is normal. When the
massage level is increased, motor resonance
will intensify accordingly.
LOCATION ENVIRONMENT
The level of sound experienced during
operation is directly related to the location
environment. For example, when a base is
located on a hardwood fl oor with the massage
feature in operation, a vibrating tone will be
audible. To minimize this resonance, place a
piece of carpet, or rubber caster cups, under
each leg or caster of the base.
It is possible to experience vibration or noise
from the headboard brackets, headboards or
footboards if mounting bolts are not fi rmly
tightened.
FABRIC CLEANING INFORMATION
Spot clean only with water based shampoo
or foam upholstery cleaner. Pretest a small,
inconspicuous area before proceeding. Do
not over wet. Do not use solvents to spot
clean. Pile fabrics may require brushing with
a non-metallic, stiff bristle brush to restore
appearance. Hot water extraction or steam
cleaning is not a recommended cleaning
method.
To prevent overall soiling, frequent vacuuming
or light brushing with a non-metallic stiff
bristle brush to remove dust and grime is
recommended. When cleaning a spill, blot
immediately to remove spilled material. Clean
spots or stains from the outside to the middle
of the affected area to prevent circling. Use a
professional furniture cleaning service when an
overall soiled condition is apparent.
Designer Series
™
99301294
23
MR2T8-TVZG REMOTE CONTROL PROGRAMMING (separating 2 bases)
REMOTE CONTROL 1
BASE 1
BASE 2
REMOTE CONTROL 2
Program Two Remotes to Operate Two Bases - your
adjustable base will be equipped with one of the following:
(A) a DC motor with a power down box, (B) an AC J box,
(C) a DC motor without a power down box (FIGURE 13).
NOTE: operate only one (1) remote control at a time.
Operating two (2) remote controls at the same time
will momentarily block both rf signals and prevent both
controls from functioning.
STEP 3
Repeat Step 1 and Step 2 with remote control 1.
Note: Wait 90 seconds before proceeding to Step 4.
STEP 4 (BASE 2)
(A) DC motor with a power down box: press the learn
button on the power down box for 1 second.
(B or C) AC Jbox or DC motor without power down
box: unplug the adjustable base electrical power
cord. Wait 30 seconds, then plug the cord back into
the power source.
STEP 5
On remote control 2, simultaneously press and hold
the foot up and tv position buttons (FIGURE 14).
The transmission indicator light will fl ash slowly and
then fl ash rapidly to indicate programming mode.
Continue to hold for 5 seconds and then release the
buttons.
STEP 6
Repeat Step 4 and Step 5 with remote control 2.
Independent remote control operation is now
restored (remote control 1 operating base 1; remote
control 2 operating base 2).
FIGURE 13: Power down box, AC J box and DC motor.
LEARN
BUTTON
POWER
DOWN BOX
AC J BOX
POWER DOWN
BOX (NOT
MOUNTED TO
BASE FRAME)
AC J BOX
(MOUNTED
TO BOTTOM
SIDE OF BASE
FRAME)
LEARN
BUTTON
DC MOTOR-NO
POWER DOWN
BOX
DC MOTOR
(MOUNTED TO
BOTTOM SIDE OF
BASE FRAME)
A
B
C
STEP 1 (BASE 1)
(A) DC motor with a power down box: press the learn
button on the power down box for 1 second.
(B or C) AC Jbox or DC motor without power down
box: unplug the adjustable base electrical power
cord. Wait 30 seconds, then plug the cord back into
the power source.
STEP 2
On remote control 1, simultaneously press and hold
the foot up and tv position buttons (FIGURE 14).
The transmission indicator light will fl ash slowly and
then fl ash rapidly to indicate programming mode.
Continue to hold for 5 seconds and then release the
buttons.
FOOT UP
BUTTON
TV POSITION
BUTTON
TRANSMISSION
INDICATOR
LIGHT
FIGURE 14