Loewe Individual 32 Compose Sound LED Operating Instructions Manual - page 24
- 24
english
Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna
selection: Continue with Setting options for DVB-S recep-
tion (see right hand column).
The normal DVB-C settings are derived from the selection
of the location and do not need to be changed.
Select and adapt settings for DVB-C reception.
You can state whether coded stations are to be searched
for in the search/update.
Select
yes
to save all found
scrambled stations. However, these stations can only be
received in connection with a CA module and the appro-
priate Smart Card.
Handling of the CA module is described
on page 57.
If a CA module with a SmartCard is already plugged in for
the station search, all the stations which this module can
descramble are also saved when no is preset.
If you want to run the station search independently of
the channel grid, select frequency search for the search
method.
The DVB stations are only searched for in the frequency
range above the start frequency.
Only change these defaults if you are familiar with other
symbol rates and types of modulation or if you have to
specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
lite, the rate of 6900 might have to be replaced by 6111.
Your cable provider has the information you need.
OK Proceed.
Setting options for DVB-S reception:
If you have not selected a DVB-S antenna in the antenna
selection: Continue with Setting options for all types of
reception on page 28.
The normal DVB-S settings are derived from the selection
of the location and do not need to be changed in most
cases.
Selecting the satellite system.
Specify how you receive which satellite(s) (single
satellite or type of satellite system). Ask your dealer
if required.
Reception of a single satellite via a connected LNC (LNB).
See page 25 for settings.
Reception of two different satellites with two LNCs (LNBs)
which are connected to the TV set by a 22 kHz switchbox.
See page 25 for settings.
Reception of two different satellites with two LNCs (LNBs)
which are connected to the TV set by a toneburst switch.
See page 25 for settings.
The TV set controls a DiSEqC multiswitch to which up to
four LNCs (LNBs) for different satellites are connected.
See page 26 for settings.
Select setting if the TV set is connected to a DiSEqC
single-cable system (according to EN 50494). Several Sat
receivers can be connected to one Sat cable. See page
26 for settings.
Select setting if the TV set is connected to a single-cable
system (without DiSEqC). Several Sat receivers can be
connected to one Sat cable. Unlike a DiSEqC single-cable
system there are restrictions in the range of certain recep-
tion frequencies in single-cable community systems. See
page 27 for settings.
OK Proceed
(to the appropriate page of the satellite system).
OK
INITIAL INSTALLATION (DVB-C)
Scrambled
stations
no
yes
Search
method
Channel
search
Start
frequency
047.0
MHz
Network
ID
none
Symbol rate 1 (DVB-C) 6875
Symbol rate 2 (DVB-C) 6900
QAM modulation 1 64
QAM modulation 2 256
Proceed
Settings
Encrypted
stations
Search
method
Start
frequency
Network ID
Symbol rate
QAM
modulation
OK
OK
INITIAL INSTALLATION (DVB-S)
Select satellite installation
Single satellite
2 satellites on 22 kHz switchbox
2 satellites on toneburst switch
Max. 4 satellites on DiSEqC multiswitch
DiSEqC one cable communal system
other communal installation
Proceed Back
Select
satellite
installation
Single
satellite
2 satellites
on 22 kHz
switchbox
2 satellites
on toneburst
switch
Max. 4
satellites
on DiSEqC
multiswitch
DiSEqC
one cable
communal
system
other
communal
installation
Initial installation