1. DL manuals
  2. NEC
  3. Voicemail
  4. Univerge SV9100
  5. Programming Manual

NEC Univerge SV9100 Programming Manual

Summary of Univerge SV9100

  • Page 1

    Programming manual nda-31579 issue 4.0 (version 5000) sv 9100 ®.

  • Page 3

    Nec corporation of america reserves the right to change the specifications, functions, or features at any time without notice. Nec corporation of america has prepared this document for use by its employees and customers. The information contained herein is the property of nec corporation of americaa...

  • Page 5

    Preface t his m anual the programming manual provides the technician with all of the necessary information for programming the univerge sv9100 system. Programming can be accomplished using a pc or a multiline terminal. S upporting d ocuments univerge sv9100 general description manual this manual pro...

  • Page 7: Chapter 1

    Sv9100 programming manual i table of contents chapter 1 introduction chapter 2 programming the univerge sv9100 program 10 : system configuration setup 10-01 : time and date ...........................................................................2-3 10-02 : location setup ............................

  • Page 8

    Ii table of contents issue 4.0 10-29 : sip server information setup .................................................. 2-50 10-31 : network keep alive setup ....................................................... 2-54 10-32 : pri networking channel limitation ...........................................

  • Page 9

    Sv9100 programming manual iii issue 4.0 11-04 : virtual extension numbering .................................................2-105 11-06 : aci extension numbering .....................................................2-107 11-07 : department group pilot numbers ..........................................

  • Page 10

    Iv table of contents issue 4.0 13-08 : telephone book system name ............................................. 2-155 13-09 : telephone book group name ............................................... 2-156 13-10 : telephone book routing ....................................................... 2-157 p...

  • Page 11

    Sv9100 programming manual v issue 4.0 15-16 : sip register id setup for extension .....................................2-225 15-17 : co message waiting indication ............................................2-226 15-18 : virtual extension key enhanced options ..............................2-227 15-1...

  • Page 12

    Vi table of contents issue 4.0 20-16 : selectable display messages ............................................... 2-280 20-17 : operator extension ............................................................... 2-283 20-18 : service tone timers .........................................................

  • Page 13

    Sv9100 programming manual vii issue 4.0 20-62 : uc exception table ...............................................................2-324 20-64 : uc web application setting ..................................................2-325 20-65 : multi-device group setup (terminal information) ....................

  • Page 14

    Viii table of contents issue 4.0 22-04 : incoming extension ring group assignment ........................ 2-365 22-05 : incoming trunk ring group assignment .............................. 2-366 22-06 : normal incoming ring mode ................................................. 2-367 22-07 : dil ass...

  • Page 15

    Sv9100 programming manual ix issue 4.0 25-04 : vrs/disa transfer ring group with no answer/busy ........2-406 25-05 : vrs/disa error message assignment .................................2-407 25-06 : vrs/disa one-digit code attendant setup .........................2-408 25-07 : system timers for vrs/...

  • Page 16

    X table of contents issue 4.0 30-04 : dss console alternate answer ............................................ 2-450 30-05 : dss console lamp table ..................................................... 2-451 30-10 : dss console ip terminal setup ........................................... 2-454 pro...

  • Page 17

    Sv9100 programming manual xi issue 4.0 program 35 : smdr account code setup 35-01 : smdr options .......................................................................2-487 35-02 : smdr output options ...........................................................2-489 35-05 : account code setup .........

  • Page 18

    Xii table of contents issue 4.0 41-22 : skill based routing setup ..................................................... 2-532 41-23 : skill table setup ................................................................... 2-533 41-24 : caller id marking setup .............................................

  • Page 19

    Sv9100 programming manual xiii issue 4.0 47-03 : sv8100 inmail group mailbox options .................................2-583 47-06 : group mailbox subscriber options ........................................2-584 47-07 : sv8100 inmail routing mailbox options ...............................2-590 47-08 ...

  • Page 20

    Xiv table of contents issue 4.0 50-13 : ccis centralized response timeout assignment ................ 2-645 50-14 : ccis intercom digits for caller id call return ...................... 2-646 50-15 : ccis over ip basic information setting ................................ 2-647 program 51 : netlink s...

  • Page 21

    Sv9100 programming manual xv issue 4.0 80-09 : short ring setup ...................................................................2-690 80-10 : dtmf tone receiver setup ..................................................2-693 80-13 : dtmf tone receiver setup - 2 ........................................

  • Page 22

    Xvi table of contents issue 4.0 program 84 : hardware setup for voip 84-01 : h.323 trunk basic information setup ................................... 2-751 84-02 : h.225 and h.245 information basic setup ............................ 2-753 84-06 : pva data setting ........................................

  • Page 23

    Sv9100 programming manual xvii issue 4.0 program 90 : maintenance program 90-01 : installation date .....................................................................2-813 90-02 : programming password setup ..............................................2-814 90-03 : save data .......................

  • Page 24

    Xviii table of contents issue 4.0 90-42 : dt800/dt700 multiline terminal version information .......... 2-863 90-43 : deleting terminal license of dt800/dt700 ......................... 2-864 90-44 : deleting terminal license of tcp interface .......................... 2-865 90-45 : temporary passwor...

  • Page 25

    Sv9100 programming manual xix issue 4.0 92-06 : fill command ........................................................................2-901 92-07 : delete command ...................................................................2-903 program 93: system information 93-01 : day/night mode information...

  • Page 26

    Xx table of contents issue 4.0 this page intentionally left blank.

  • Page 27

    Sv9100 programming manual xxi list of tables table 1-1 sv9100 terminal keys for entering data ......................................................... 1-4 table 1-2 ux5000 terminal keys for entering data ......................................................... 1-5 table 1-3 keys for entering names...

  • Page 28

    Xxii list of tables issue 4.0 table 2-19 ring cycle table ........................................................................................... 2-691 table 2-20 default table ................................................................................................. 2-694.

  • Page 29: Chapter 1

    Sv9100 programming manual 1-1 chapter 1 univerge ® sv9100 introduction s ection 1 b efore y ou s tart p rogramming this chapter provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this chapter,...

  • Page 30

    Issue 4.0 1-2 introduction 1. Enter the programming mode. 2. 15-07-01 tells you to enter the programming mode, dial 150701 from the telephone dial pad. After you do, you will see the message “15-07-01 tel” on the first line of the telephone display. This indicates the program number (15-07), item nu...

  • Page 31

    Issue 4.0 sv9100 programming manual 1-3 s ection 4 h ow to e xit p rogramming m ode to exit the programming mode: when you are done programming, you must be out of a program option to exit (pressing the answer key will exit the program option). 1. Press answer key to exit the program options, if nee...

  • Page 32

    Issue 4.0 1-4 introduction s ection 5 u sing k eys to m ove a round in the p rograms once you enter the programming mode, use the keys in the following chart to enter data, edit data and move around in the menus. Table 1-1 sv9100 terminal keys for entering data sv9100 terminal keys for entering data...

  • Page 33

    Issue 4.0 sv9100 programming manual 1-5 table 1-2 ux5000 terminal keys for entering data ux5000 terminal keys for entering data use this key... When you want to . . . 0~9 and  enter data into a program. Hold complete the programming step you just made (like pressing enter on a pc keyboard). When a ...

  • Page 34

    Issue 4.0 1-6 introduction s ection 6 p rogramming n ames and t ext m essages several programs (e.G., program 20-16 : selectable display messages) require you to enter text. Use the following chart when entering and editing text. When using the keypad digits, press the key once for the first charact...

  • Page 35

    Issue 4.0 sv9100 programming manual 1-7 s ection 7 u sing s oftkeys f or p rogramming each univerge sv9100 display telephone provides interactive softkeys for intuitive feature access. The options for these keys will automatically change depending on where you are in the system programming. Simply p...

  • Page 36

    Issue 4.0 1-8 introduction s ection 9 s ystem n umber p lan /c apacities the following table provides the capacities for the univerge sv9100 system. Table 1-5 system number plan/capacities system number plan/capacities system type number plan/capacities system analog caller id detector (detected by ...

  • Page 37

    Issue 4.0 sv9100 programming manual 1-9 extension telephone extension ports multiline terminals single line phones/analog devices voip extensions sip dect wireless 960 256 256 512 504 dlca: physical ports 01~16 lca: physical ports 01~16 telephone extension number range 1~89999999* (*extension cannot...

  • Page 38

    Issue 4.0 1-10 introduction speed dialing speed dialing groups 64 speed dialing bins 0~9999 speed dialing table-common 1000 contact center contact center groups 64 contact center agent extensions 960 aci aci groups 16 aci ports 96 automated attendant vrs message numbers 1~100 conference conference c...

  • Page 39

    Issue 4.0 sv9100 programming manual 1-11 paging and park internal page group numbers 0, 01~64 external page group numbers 0, 1~8 external speakers gcd-cp10 pgd(2)-u10 adp 9 (1) (1~8) park group numbers 1~64 park orbits 1~64 smdr smdr ports 1~8 vrs/vm8000 inmail vrs/vm8000 inmail 1 vrs/vm8000 inmail ...

  • Page 40

    Issue 4.0 1-12 introduction level 4 (sb) pcpro/webpro user name: 9999 admin2 programming password users 8 footnotes extension numbers can be one to eight digits long. Refer to the flexible system numbering feature in the univerge sv9100 features and specifications manual. Table 1-5 system number pla...

  • Page 41: Chapter 2

    Sv9100 programming manual 2-1 chapter 2 univerge ® sv9100 programming the univerge sv9100 s ection 1 p rogramming y our s ystem the information contained in this chapter provides the information necessary to properly program your univerge univerge sv9100 system. The programming blocks are organized ...

  • Page 42

    Issue 4.0 2-2 programming the univerge sv9100 program 40 : voice recording system program 41 : acd setup program 42 : hotel setup program 44 : ars/f-route setup program 45 : voice mail integration program 47 : inmail program 50 : common channel interoffice signaling service (ccis) program 51 : netli...

  • Page 43: 10-01 : Time and Date

    Sv9100 programming manual 2-3 program: 10 description use program 10-01 : time and date to change the system time and date through system programming. Extension users can also dial service code 828 to change the time if allowed by an extension class of service. Conditions none feature cross referenc...

  • Page 44: 10-02 : Location Setup

    Issue 4.0 2-4 program 10 : system configuration setup description use program 10-02 : location setup to define the location of the installed system. Conditions none feature cross reference none program 10 : system configuration setup 10-02 : location setup level: sa input data item no. Item input da...

  • Page 45: 10-03 : Etu Setup

    Issue 4.0 sv9100 programming manual 2-5 description use program 10-03 : etusetup to setup and confirm the basic configuration data for each blade. When changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatically define it or you may have...

  • Page 46

    Issue 4.0 2-6 program 10 : system configuration setup item no. Item input data default 01 terminal type (b1) 0 = not set 1 = multiline terminal 2 = slt adapter 3 = bluetooth cordless handset (bch) 4 = --- not used --- 5 = --- not used --- 6 = pgd(2)-u10 adp (paging) 7 = pgd(2)-u10 adp (tone ringer) ...

  • Page 47

    Issue 4.0 sv9100 programming manual 2-7 for lca pkg setup 07 logical port number (b2) 0 = not set 6 = pgd(2)-u10 adp (ext. Speaker) 7 = pgd(2)-u10 adp (paging/tone ringer) = (1~8) 8 = pgd(2)-u10 adp (for door box) = (1~8) 9 = pgd(2)-u10 adp (aci) = (1~96) 12 = apr (for b2 mode) (193~512) 0 08 multil...

  • Page 48

    Issue 4.0 2-8 program 10 : system configuration setup for cota unit setup for gcd-pvaa unit setup for odta pkg setup input data physical port number 1~8 item no. Item input data default 01 logical port number 0~400 0 input data physical port number 01~200 item no. Item input data default 01 logical ...

  • Page 49

    Issue 4.0 sv9100 programming manual 2-9 for diop pkg setup for bria pkg setup input data physical port number 01~04 item no. Item input data default 01 ld/opx specification 0 = ld trunk 1 = opx 0 02 logical port number 0 = 1~400 (ld trunk) 1 = 1~960 (opx) 0 input data isdn line number 01~04 item no ...

  • Page 50

    Issue 4.0 2-10 program 10 : system configuration setup 04 layer 3 timer type each timer value of layer 3 is set up for every type using program 81-06 (t-bus). 1~5 1 05 clip information announcement based on this setting, the system includes a presentation allowed (1) or presentation restricted (0) i...

  • Page 51

    Issue 4.0 sv9100 programming manual 2-11 for prta pkg setup 19 numbering plan identification isdn protocol definition 0 = unknown 1 = isdn numbering plan 2 = data numbering plan 3 = telex numbering plan 4 = national standard numbering plan 5 = private numbering plan 1 23 straight/cross wiring 0 = au...

  • Page 52

    Issue 4.0 2-12 program 10 : system configuration setup 03 --- not used --- 04 layer 3 timer type each timer value of layer 3 is set up for each type in program 81-06 (t-bus) 1~5 1 05 clip information based on this setting, the system includes a presentation allowed (1) or presentation restricted (0)...

  • Page 53

    Issue 4.0 sv9100 programming manual 2-13 16 pri service two b-channel transfer turn on or off the ability to use the isdn-pri 2 b-channel transfer service. 0 = off 1 = on 0 17 isdn ringback tone if telco does not provide ringback tone, sv9100 can if 10-03-17 is set to 1 (enable). 0 = disable 1 = ena...

  • Page 54

    Issue 4.0 2-14 program 10 : system configuration setup for dti (t1) pkg setup input data physical port number 01~24 item no. Item input data default 01 logical port number the start port number of a t1 line is displayed, and 24 logic ports are automatically assigned to a dti (t1) line. 0~400 0 02 t1...

  • Page 55

    Issue 4.0 sv9100 programming manual 2-15 for iple pkg setup for gcd-vm00 pkg setup for gcd-ccta pkg setup item no. Item input data 01 voip type iple 02 number of channel 256 03 number of voice channels 256 input data physical port number 01~16 item no. Item input data default 01 logical port number ...

  • Page 56

    Issue 4.0 2-16 program 10 : system configuration setup conditions when changing a defined terminal type, first set the type to 0 and then plug the new device in to have the system automatically define it, or redefine the type manually. The system must have a blade installed to view/change the option...

  • Page 57: 10-04 : Music On Hold Setup

    Issue 4.0 sv9100 programming manual 2-17 description use program 10-04 : music on hold setup to set the music on hold (moh) source. For internal music on hold, the system can provide a service tone to callers on hold, or one of eleven synthesized selections. Program 10 : system configuration setup 1...

  • Page 58

    Issue 4.0 2-18 program 10 : system configuration setup conditions none feature cross reference analog communications interface (aci) background music music on hold 05 sub-music on hold tone selection [if item 4 is 1] 0 = no tone 1 = download file1 2 = download file2 3 = download file3 [if item 4 is ...

  • Page 59

    Issue 4.0 sv9100 programming manual 2-19 description use program 10-05 : general purpose relay setup to define which relay circuits (5~8) on pgd(2)- u10 adp are used for general purpose relay. Input data conditions none feature cross reference analog communications interface (aci) program 10 : syste...

  • Page 60: 10-06 : Isdn-Bri Setup

    Issue 4.0 2-20 program 10 : system configuration setup description use program 10-06 : isdn - bri setup to configure the isdn - bri terminal endpoint identifier (tei), mode of operation, and service profile identifier (spid) number for each circuit b-channels. Conditions none feature cross reference...

  • Page 61: 10-08 : Pre-Ringing Setup

    Issue 4.0 sv9100 programming manual 2-21 description use program 10-08 : pre-ringing setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk led flashes. The call then continues ringin...

  • Page 62

    Issue 4.0 2-22 program 10 : system configuration setup description use program 10-09 : dtmf and dial tone circuit setup to allocate the circuits on the gcd-cp10 for either dtmf receiving or dial tone detection. The gcd-cp10 has 80 circuits initially, and an addition 64 circuits are added when a gpz-...

  • Page 63

    Issue 4.0 sv9100 programming manual 2-23 conditions none feature cross reference caller id central office calls, placing direct inward dialing (did) direct inward system access (disa) tie lines.

  • Page 64

    Issue 4.0 2-24 program 10 : system configuration setup description use program 10-12 : gcd-cp10 network setup to setup the ip address, subnet-mask, and default gateway addresses. Program 10 : system configuration setup 10-12 : gcd-cp10 network setup level: sa input data item no. Item input data defa...

  • Page 65

    Issue 4.0 sv9100 programming manual 2-25 04 time zone 0~24 (0 = -12 hours and 24 = +12 hours) +7 (-5 hours) determine the offset from greenwich mean time (gmt) time. Then enter its respective value. For example, eastern time (us and canada) has a gmt offset of -5. The program data would then be 7 (0...

  • Page 66

    Issue 4.0 2-26 program 10 : system configuration setup 10 subnet mask 128.0.0.0 192.0.0.0 224.0.0.0 240.0.0.0 248.0.0.0 252.0.0.0 254.0.0.0 255.0.0.0 255.128.0.0 255.192.0.0 255.224.0.0 255.240.0.0 255.248.0.0 255.252.0.0 255.254.0.0 255.255.0.0 255.255.128.0 255.255.192.0 255.255.224.0 255.255.240....

  • Page 67

    Issue 4.0 sv9100 programming manual 2-27 conditions none feature cross reference voice over internet protocol (voip) 20 sslv3 setting 0 = disable 1 = enable 0 set whether to use the sslv3 in smtp. 0 (disable) is encrypted with tlsv1. This data requires a reset to apply changed data to the system. 21...

  • Page 68: 10-13 : In-Dhcp Server Setup

    Issue 4.0 2-28 program 10 : system configuration setup description use program 10-13 : in-dhcp server setup to setup the dhcp server built into the gcd-cp10 blade. Conditions none feature cross reference voice over internet protocol (voip) program 10 : system configuration setup 10-13 : in-dhcp serv...

  • Page 69

    Issue 4.0 sv9100 programming manual 2-29 description use program 10-14 : managed network setup to set up the range of the ip address which the dhcp server leases to a client. Conditions none feature cross reference voice over internet protocol (voip) program 10 : system configuration setup 10-14 : m...

  • Page 70

    Issue 4.0 2-30 program 10 : system configuration setup description use program 10-15 : client information setup to set up the client information when the dhcp server needs to assign a fixed ip address to clients. Conditions none feature cross reference voice over internet protocol (voip) program 10 ...

  • Page 71

    Issue 4.0 sv9100 programming manual 2-31 description use program 10-16 : option information setup to set up the option given from the dhcp server to each client. Program 10 : system configuration setup 10-16 : option information setup level: sa input data item no. Item input data default 01 router s...

  • Page 72

    Issue 4.0 2-32 program 10 : system configuration setup 07 dns domain name set the dns domain name. Code number 0~255 15 (fixed) maximum 20 character strings no setting 08 download protocol set download protocol used for autoconfig (for dt700 series). Code number 0~255 43 (fixed) sub code number 163 ...

  • Page 73

    Issue 4.0 sv9100 programming manual 2-33 16 sip server (ip address) code number 0~255 120 (fixed) ip address 0.0.0.0 ~ 126.255.255.254 128.0.0.1 ~ 191.255.255.254 192.0.0.1 ~ 223.255.255.254 172.16.0.10 17 sip server (domain name) code number 0~255 120 (fixed) maximum 20 character strings no setting...

  • Page 74

    Issue 4.0 2-34 program 10 : system configuration setup conditions none feature cross reference voice over internet protocol (voip) 27 sip server receive port code number 0~255 168 (fixed) port: 1~65535 5080 28 config file name code number 0~255 43 (fixed) sub-code number 0~255 152 up to 15 character...

  • Page 75

    Issue 4.0 sv9100 programming manual 2-35 description use program 10-17 : h.323 gatekeeper setup to set the h.323 gatekeeper information. Conditions none feature cross reference ip trunk – h.323 program 10 : system configuration setup 10-17 : h.323 gatekeeper setup level: sa input data item name inpu...

  • Page 76

    Issue 4.0 2-36 program 10 : system configuration setup description use program 10-18 : h.323 alias address setup to set the alias address registered to the outside h.323 gatekeeper. Conditions none feature cross reference ip trunk – h.323 program 10 : system configuration setup 10-18 : h.323 alias a...

  • Page 77

    Issue 4.0 sv9100 programming manual 2-37 description use program 10-19 : voip dsp resource selection to define the criteria for each dsp resource on the voip blade. Conditions none feature cross reference none program 10 : system configuration setup 10-19 : voip dsp resource selection level: sa inpu...

  • Page 78

    Issue 4.0 2-38 program 10 : system configuration setup description use program 10-20 : lan setup for external equipment to define the tcp port/address/etc. For communicating to external equipment. Program 10 : system configuration setup 10-20 : lan setup for external equipment level: in input data t...

  • Page 79

    Issue 4.0 sv9100 programming manual 2-39 conditions none feature cross reference none.

  • Page 80

    Issue 4.0 2-40 program 10 : system configuration setup description use program 10-21 : gcd-cp10 hardware setup to set up various hardware, such as the baud rate of com port and the switch for control on gcd-cp10 blade. Program 10 : system configuration setup 10-21 : gcd-cp10 hardware setup level: in...

  • Page 81

    Issue 4.0 sv9100 programming manual 2-41 conditions none feature cross reference none.

  • Page 82

    Issue 4.0 2-42 program 10 : system configuration setup description use program 10-23 : sip system interconnection setup to determine if the system is interconnected and define the ip address of another system, call control port number and alias address for sv9100 system interconnection. Conditions n...

  • Page 83

    Issue 4.0 sv9100 programming manual 2-43 feature cross reference none.

  • Page 84

    Issue 4.0 2-44 program 10 : system configuration setup description use program 10-24 : daylight saving setup to set the options for daylight savings. As the telephone system is used globally, these settings define when the system should automatically adjust for daylight savings as it applies to the ...

  • Page 85

    Issue 4.0 sv9100 programming manual 2-45 conditions none feature cross reference clock/calendar display 08 end of week day enter the day of the week when the system should adjust the time for daylight savings time (01 = sunday, 02 = monday, etc.). 1~7 (sun = 1, mon = 2, etc.) 1 input data item no. I...

  • Page 86

    Issue 4.0 2-46 program 10 : system configuration setup description use program 10-25 : h.323 gateway prefix setup to set the gateway prefix registered to the outside gatekeeper. Conditions none feature cross reference none program 10 : system configuration setup 10-25 : h.323 gateway prefix setup le...

  • Page 87: 10-27 : Ip System Id

    Issue 4.0 sv9100 programming manual 2-47 description use program 10-27 : ip system id to set the ip address of the networked ip systems. Conditions none feature cross reference none program 10 : system configuration setup 10-27 : ip system id level: in input data item no. Item input data default 01 ...

  • Page 88

    Issue 4.0 2-48 program 10 : system configuration setup description use program 10-28 : sip system information setup to set up basic sip trunking. Program 10 : system configuration setup 10-28 : sip system information setup level: in input data item no. Item input data default profile 1~6 01 domain n...

  • Page 89

    Issue 4.0 sv9100 programming manual 2-49 conditions none feature cross reference none 06 ip trunk port binding trunk port binding is only used for sip trunks to the provider in non- registration mode only. When this is disabled, an inbound call comes in and follows your did routing but it comes in o...

  • Page 90

    Issue 4.0 2-50 program 10 : system configuration setup description use program 10-29 : sip server information setup to define the sip proxy setup for outbound/ inbound. The 10-29 commands are not used in non-registration mode. Program 10 : system configuration setup 10-29 : sip server information se...

  • Page 91

    Issue 4.0 sv9100 programming manual 2-51 03 default proxy ip address this is optional and used if the provider gives you a proxy address that is different than the registration address. If the provider is using domain names instead of ip addresses, leave this at default. 0.0.0.0 ~ 126.255.255.254 12...

  • Page 92

    Issue 4.0 2-52 program 10 : system configuration setup 15 registration expiry (expire) time set the expiration time when the sip trunk registers to the sip server. When half the time set here passes, the registration update is automatically done. 120 ~ 65535 seconds 3600 16 register sub mode prevent...

  • Page 93

    Issue 4.0 sv9100 programming manual 2-53 conditions none feature cross reference none.

  • Page 94

    Issue 4.0 2-54 program 10 : system configuration setup description use program 10-31 : network keep alive setup to set the interval and retry count of the aspirenet networking keep alive message. The keep alive is used for isdn and ip networking. The keep alive message is automatically responded to ...

  • Page 95

    Issue 4.0 sv9100 programming manual 2-55 conditions the keep alive message must be sent and a response not received for the retry count, for the link to be taken out of service and the calls in progress and park hold orbits to be released. For example, if an isdn netlink connection is disconnected a...

  • Page 96

    Issue 4.0 2-56 program 10 : system configuration setup description use program 10-32 : pri networking channel limitation to assign the number of b-channels to be used for each isdn blade. This allows for fractional pris when used with multiple site networking. If this program is limited to less than...

  • Page 97

    Issue 4.0 sv9100 programming manual 2-57 description use program 10-33 : sip registrar/proxy information basic setup to set the registrar/proxy options for sip extensions. Conditions none feature cross reference none program 10 : system configuration setup 10-33 : sip registrar/proxy information bas...

  • Page 98

    Issue 4.0 2-58 program 10 : system configuration setup description use program 10-36 : sip trunk registration information setup to set the sip trunk registration information. Conditions none feature cross reference none program 10 : system configuration setup 10-36 : sip trunk registration informati...

  • Page 99: 10-37 : Upnp Setup

    Issue 4.0 sv9100 programming manual 2-59 description use program 10-37 : upnp setup to set the upnp (universal plug and play) options for sip trunks. Conditions none feature cross reference none program 10 : system configuration setup 10-37 : upnp setup level: in input data item no. Item input data ...

  • Page 100: 10-38 : Bgm Resource Setup

    Issue 4.0 2-60 program 10 : system configuration setup description use program 10-38 : bgm resource setup to configure the background music source input. Conditions none feature cross reference analog communications interface (aci) background music program 10 : system configuration setup 10-38 : bgm...

  • Page 101: 10-39 : Fractional Setup

    Issue 4.0 sv9100 programming manual 2-61 description use program 10-39 : fractional setup to enable or disable the ability to use fractional t1 or pri. Conditions none feature cross reference none program 10 : system configuration setup 10-39 : fractional setup level: in input data item no. Item inp...

  • Page 102

    Issue 4.0 2-62 program 10 : system configuration setup description use program 10-41 : general purpose contact detector to assign system number/slot number, esiu port number and circuit number settings used by the pgd(2)-u10 adp. Conditions none feature cross reference none program 10 : system confi...

  • Page 103

    Issue 4.0 sv9100 programming manual 2-63 description use program 10-42 : virtual loop back port setting to set the data for the virtual loop back port. Conditions none feature cross reference station message detail recording (smdr) hotel/motel transfer program 10 : system configuration setup 10-42 :...

  • Page 104

    Issue 4.0 2-64 program 10 : system configuration setup description use program 10-46 : dt800/dt700 server information setup to setup the information of sip multiline (dt700 series) server. Program 10 : system configuration setup 10-46 : dt800/dt700 server information setup level: in input data item ...

  • Page 105

    Issue 4.0 sv9100 programming manual 2-65 06 register port assign the port number in which the sip messages are sent to on the iple. This same port number must be assigned in the sip multiline terminals. If this command is changed, it requires a cpu reset. When using netlink (program 51- 01-01) this ...

  • Page 106

    Issue 4.0 2-66 program 10 : system configuration setup 12 multicast port the port number that is used for paging will change based upon the following information. The formula for the ports that will be used is: starting port number assigned in 10-46-12 + management id * 2 the value of the management...

  • Page 107

    Issue 4.0 sv9100 programming manual 2-67 conditions none feature cross reference none.

  • Page 108

    Issue 4.0 2-68 program 10 : system configuration setup description use program 10-47 : terminal license server information setup to setup the information of terminal license server. Conditions none feature cross reference none program 10 : system configuration setup 10-47 : terminal license server i...

  • Page 109: 10-48 : License Activation

    Issue 4.0 sv9100 programming manual 2-69 description use program 10-48 : license activation to turn on the license issued from the license server. Conditions none feature cross reference none program 10 : system configuration setup 10-48 : license activation level: in input data item no. Item input ...

  • Page 110

    Issue 4.0 2-70 program 10 : system configuration setup description use program 10-49 : license file activation to enable the command to save the license file via usb memory which is issued from the license server. Conditions none feature cross reference none program 10 : system configuration setup 1...

  • Page 111: 10-50 : License Information

    Issue 4.0 sv9100 programming manual 2-71 description use program 10-50 : license information to confirm license information that is stored in a system. Refer to the following table to assist with licensing information. Program 10 : system configuration setup 10-50 : license information level: in inp...

  • Page 112

    Issue 4.0 2-72 program 10 : system configuration setup 0046 sv9100 pms lic pms on/off – 0047 sv9100 remote conf lic-01 remote conference 1 20 – 0048 sv9100 hw migration lic h/w migration on/off – 0049 sv9100 multi-device multi-device 1 512 – 0080 sv9100 web video conference video conference with web...

  • Page 113

    Issue 4.0 sv9100 programming manual 2-73 1410 sv91/93 um8000 tts lang-lic 01 ums tts language 1 10 1 port of text-to-speech language activation license. 2002 sv9100 contact center agent-lic 01 acd client 1 896 – 2101 sv9100 contact center p-event lic acd p-event on/off 2102 sv9100 contact center- mi...

  • Page 114

    Issue 4.0 2-74 program 10 : system configuration setup 3203 sv91/93 ip recorder - ip recorder-lic 01 ip rec add 256 1 256 3204 sv91/93 ip recorder - call scoring-lic 01 ip rec callscoring 1 999 3205 sv91/93 ip recorder - reporting-lic ip call reporting on/off 3210 sv91/93/95 ip/digital- report-lic 0...

  • Page 115

    Issue 4.0 sv9100 programming manual 2-75 conditions confirm license by entering feature code no. (0~9999) feature cross reference none 5303 sv9100 ucs softphone e client-lic01 ucs softphone enhance 1 256 – 5304 sv9100 ucs attendant client-lic 01 ucs attendant client 1 512 – 5305 sv9100 ucs client-li...

  • Page 116

    Issue 4.0 2-76 program 10 : system configuration setup description use program 10-51 : pri/t1 selection of cd-prtato select whether the cd-prta works as pri or t1. Conditions none feature cross reference none program 10 : system configuration setup 10-51 : pri/t1 selection of cd-prta level: in input...

  • Page 117

    Issue 4.0 sv9100 programming manual 2-77 description use program 10-52 : free/demo license information to display information on free of charge/demo license. Conditions none feature cross reference none program 10 : system configuration setup 10-52 : free/demo license information level: in input dat...

  • Page 118

    Issue 4.0 2-78 program 10 : system configuration setup description use program 10-54 : license configuration for each package to set the license information for each unit. Conditions if applying more than 255 licenses to a slot the licenses must be applied across multiple indexes. For example assign...

  • Page 119

    Issue 4.0 sv9100 programming manual 2-79 description use program 10-55 : package network setup to set the network information for each unit. This program sets the spoe of each package. Program 10 : system configuration setup 10-55 : package network setup level: in input data slot number 1~24 item no...

  • Page 120

    Issue 4.0 2-80 program 10 : system configuration setup conditions none feature cross reference none 05 default gateway 0.0.0.0~126.255.255.254 128.0.0.1~191.255.255.254 192.0.0.1~223.255.255.254 0.0.0.0 item no. Item input data default.

  • Page 121: 10-56 : Xml Portal Ip Phone

    Issue 4.0 sv9100 programming manual 2-81 description use program 10-56 : xml portal ip phone to set the contents of xml portal page provided to the ip phone. The xml portal page is included in the xml application name and url link information. Xml url link information can be set for up to five syste...

  • Page 122

    Issue 4.0 2-82 program 10 : system configuration setup description use program 10-58 : dt800/dt700 network setup to set the local network address when the sip multiline terminal connects the system via a local router. Conditions none feature cross reference none program 10 : system configuration set...

  • Page 123: 10-62 : Netbios  Setting

    Issue 4.0 sv9100 programming manual 2-83 description use program 10-62 : netbios setting to set the netbios which is used to access webpro of sv9100 using http and https. Conditions none feature cross reference none program 10 : system configuration setup 10-62 : netbios setting level: in input data...

  • Page 124: 10-65 : Ntp Server

    Issue 4.0 2-84 program 10 : system configuration setup description use program 10-65 : ntp server to set the ntp (network time protocol) server which is built-in the cpu. Ntp server can synchronize the time for ip video door phone, or ntp clients connected to the sv9100 network. Conditions none feat...

  • Page 125

    Issue 4.0 sv9100 programming manual 2-85 description use program 10-67 : sip stack configuration setup to program sip system base setting. Conditions the sip stack cannot separate dns servers, only one dns server can be used. Feature cross reference none program 10 : system configuration setup 10-67...

  • Page 126

    Issue 4.0 2-86 program 10 : system configuration setup.

  • Page 127

    Issue 4.0 sv9100 programming manual 2-87 description use program 10-68 : ip trunk availability to set the number of ports available for ip trunking. Conditions none feature cross reference none program 10 : system configuration setup 10-68 : ip trunk availability level: in index 1 system id 0~50 inp...

  • Page 128

    Issue 4.0 2-88 program 10 : system configuration setup description use program 10-69 : uc server general settings to set the general settings for the uc server program 10 : system configuration setup 10-69 : uc server general settings level: in input data item no. Item input data default 01 uc serve...

  • Page 129

    Issue 4.0 sv9100 programming manual 2-89 conditions none feature cross reference none 12 uc server auto restart day 0: sunday 1: monday 2: tuesday 3: wednesday 4: thursday 5: friday 6: saturday 0 13 uc server auto restart time 00:00 ~ 23:59 00:00 input data item no. Item input data default.

  • Page 130

    Issue 4.0 2-90 program 10 : system configuration setup description use program 10-70 : uc server voicemail interface settings to configure the voicemail integration for the uc server. To set . Conditions none feature cross reference none program 10 : system configuration setup 10-70 : uc server voic...

  • Page 131

    Issue 4.0 sv9100 programming manual 2-91 description use program 10-71 : uc server contact center settings to define the ip address and port uc clients with contact center integration will connect to . Conditions none feature cross reference none program 10 : system configuration setup 10-71 : uc se...

  • Page 132

    Issue 4.0 2-92 program 10 : system configuration setup description use program 10-72 : network security setup to define the server certificate and the private key for tls connection when the sv9100 receives a tls request. Conditions none feature cross reference tls on sip program 10 : system configu...

  • Page 133

    Issue 4.0 sv9100 programming manual 2-93.

  • Page 134

    Issue 4.0 2-94 program 10 : system configuration setup.

  • Page 135: 11-01 : System Numbering

    Sv9100 programming manual 2-95 program: 11 description use program 11-01 : system numbering to set the system numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other extensions and features, such as service code...

  • Page 136

    Issue 4.0 2-96 program 11 : system numbering step 2: specify the length of the code you want to change after you specify a single- or two-digit code, you must tell the system how many digits comprise the code. This is the number of digits required column in the table 2-3 system numbering default set...

  • Page 137

    Issue 4.0 sv9100 programming manual 2-97 default see the following tables for default settings. Table 2-3 system numbering default settings dial types: 1=service code, 2=extension number, 3=trunk access, 4=special trunk access, 5=operator access, 6=flexible routing, 8 = networking 9 = dial extension...

  • Page 138

    Issue 4.0 2-98 program 11 : system numbering 31 0 0 32 0 0 33 0 0 34 0 0 35 0 0 36 0 0 37 0 0 38 0 0 39 0 0 30 0 0 3 0 0 3 # 0 0 4x 3 1 41 0 0 42 0 0 43 0 0 44 0 0 45 0 0 46 0 0 47 0 0 48 0 0 49 0 0 40 0 0 4 0 0 4 # 0 0 5x 3 1 51 0 0 52 0 0 53 0 0 table 2-3 system numbering default settings (continu...

  • Page 139

    Issue 4.0 sv9100 programming manual 2-99 54 0 0 55 0 0 56 0 0 57 0 0 58 0 0 59 0 0 50 0 0 5 0 0 5 # 0 0 6x 3 1 61 0 0 62 0 0 63 0 0 64 0 0 65 0 0 66 0 0 67 0 0 68 0 0 69 0 0 60 0 0 6 0 0 6 # 0 0 7x 3 1 71 0 0 72 0 0 73 0 0 74 0 0 75 0 0 76 0 0 table 2-3 system numbering default settings (continued) ...

  • Page 140

    Issue 4.0 2-100 program 11 : system numbering 77 0 0 78 0 0 79 0 0 70 0 0 7 0 0 7 # 0 0 8x 1 1 81 0 0 82 0 0 83 0 0 84 0 0 85 0 0 86 0 0 87 0 0 88 0 0 89 0 0 80 0 0 8 0 0 8 # 0 0 9x 1 3 91 0 0 92 0 0 93 0 0 94 0 0 95 0 0 96 0 0 97 0 0 98 0 0 99 0 0 table 2-3 system numbering default settings (contin...

  • Page 141

    Issue 4.0 sv9100 programming manual 2-101 90 0 0 9 0 0 9 # 0 0 0x 1 5 01 0 0 02 0 0 03 0 0 04 0 0 05 0 0 06 0 0 07 0 0 08 0 0 09 0 0 00 0 0 0 0 0 0 # 0 0 x 2 1 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 0 0 0 0 0 # 0 0 table 2-3 system numbering default settings (continued) dial types: 1=...

  • Page 142

    Issue 4.0 2-102 program 11 : system numbering conditions none feature cross reference flexible system numbering # x 0 0 # 1 2 1 # 2 2 1 # 3 2 1 # 4 2 1 # 5 2 1 # 6 2 1 # 7 2 1 # 8 2 1 # 9 2 1 # 0 2 1 # 4 1 ## 2 1 table 2-3 system numbering default settings (continued) dial types: 1=service code, 2=e...

  • Page 143: 11-02 : Extension Numbering

    Issue 4.0 sv9100 programming manual 2-103 description use program 11-02 : extension numbering to set the extension number. The extension number can have up to eight digits. The first/second digit(s) of the number should be assigned in program 11-01 or program 11-20. This allows an employee to move t...

  • Page 144

    Issue 4.0 2-104 program 11 : system numbering feature cross reference department calling flexible system numbering intercom.

  • Page 145

    Issue 4.0 sv9100 programming manual 2-105 description use program 11-04 : virtual extension numbering to define the virtual extension numbers. The extension number can have up to eight digits. The first/second digit(s) of the number should be assigned in program 11-01 or program 11-20. Default condi...

  • Page 146

    Issue 4.0 2-106 program 11 : system numbering feature cross reference flexible system numbering multiple directory numbers / call coverage.

  • Page 147

    Issue 4.0 sv9100 programming manual 2-107 description use program 11-06 : aci extension numbering to define the virtual extension number used for the aci. The extension number can have up to eight digits. The first and second digits of the number should be assigned in program 11-01 or program 11-20....

  • Page 148

    Issue 4.0 2-108 program 11 : system numbering description use program 11-07 : department group pilot numbers to assign a pilot number to each department group set up in program 16-02. The pilot number is the number users dial for department calling and department step calling. The pilot number can h...

  • Page 149

    Issue 4.0 sv9100 programming manual 2-109 feature cross reference department calling department step calling.

  • Page 150

    Issue 4.0 2-110 program 11 : system numbering description use program 11-08 : aci group pilot number to assign the pilot number to the aci groups set in program 33-02. The pilot number can have up to four digits. The first and second digits of the number should be assigned in program 11-01 or progra...

  • Page 151: 11-09 : Trunk Access Code

    Issue 4.0 sv9100 programming manual 2-111 description use program 11-09 : trunk access code to assign the trunk access code (normally 9). The trunk access code can be set from 1~8 digits which is defined to type 3 and 4 in program 11-01. This is the code extension users dial to access automatic rout...

  • Page 152

    Issue 4.0 2-112 program 11 : system numbering feature cross reference automatic route selection central office calls, placing trunk group routing.

  • Page 153

    Issue 4.0 sv9100 programming manual 2-113 description use program 11-10 : service code setup (for system administrator) to customize the service codes for the system administrator. You can customize additional service codes in programs 11-11~11-16. The following chart shows: the number of each code ...

  • Page 154

    Issue 4.0 2-114 program 11 : system numbering 12 night mode switching for other group mlt 618 12-xx 20-07-01 13 --- not used --- 14 --- not used --- 15 --- not used --- 16 leaving message waiting (requires cpu to be licensed for hotel/motel) mlt 626 11-11-09 17 dial block by supervisor mlt 601 90-19...

  • Page 155

    Issue 4.0 sv9100 programming manual 2-115 conditions none feature cross reference refer to input data chart on the previous pages. 36 change the guidance message number on voice mail auto attendant mlt, slt not set 37 --- not used --- 38 --- not used --- 39 --- not used --- 40 --- not used --- 41 da...

  • Page 156

    Issue 4.0 2-116 program 11 : system numbering description use program 11-11 : service code setup (for setup/entry operation) to customize the service codes which are used for registration and setup. You can customize additional service codes in programs 11-10, and 11-12 ~ 11-16. The following chart ...

  • Page 157

    Issue 4.0 sv9100 programming manual 2-117 13 display language selection for multiline terminal mlt 678 15-02 14 text message setting mlt no setting 15 enable handsfree incoming intercom calls mlt 721 20-09-05 20-02-12 16 force ringing of incoming intercom calls mlt 723 20-09-05 20-02-12 17 programma...

  • Page 158

    Issue 4.0 2-118 program 11 : system numbering 35 pilot group withdrawing mlt, slt 650 36 toll restriction override mlt, slt 663 21-14 37 ring volume set mlt 729 38 programmable function key programming (3-digit service codes) mlt 752 15-07 11-11-17 39 station speed dial number entry mlt, slt 755 40 ...

  • Page 159

    Issue 4.0 sv9100 programming manual 2-119 conditions none feature cross reference refer to the input data chart above. 57 set do not call table mlt, slt no setting 58 call forward with personal greeting mlt, slt 713 59 call forward to attendant except busy mlt, slt no setting 15-01-08 60 call forwar...

  • Page 160

    Issue 4.0 2-120 program 11 : system numbering description use program 11-12 : service code setup (for service access) to customize the service codes which are used for service access. You can customize additional service codes in programs 11-10, 11- 11, and 11-13 through 11-16. The following chart s...

  • Page 161

    Issue 4.0 sv9100 programming manual 2-121 11 group speed dialing mlt, slt # 4 12 last number dial mlt, slt # 5 13 saved number dial mlt, slt 715 14 trunk group access mlt, slt 704 15 specified trunk access mlt, slt # 9 16 trunk access via networking mlt, slt no setting 17 clear last number dialing d...

  • Page 162

    Issue 4.0 2-122 program 11 : system numbering 39 --- not used --- 40 station speed dialing mlt, slt # 7 41 voice over mlt, slt 690 11-16-08 42 flash on trunk lines slt # 3 43 answer no-ring line (universal answer) mlt, slt # 0 14-05 14-06 44 callback test for slt slt 799 45 enabled on hook when hold...

  • Page 163

    Issue 4.0 sv9100 programming manual 2-123 conditions none feature cross reference refer to the input data chart on the previous pages. 62 security sensor rest mlt, slt 716 63 watch mode start mlt, slt 717 64 security sensor mode start mlt, slt 719 mlt = multiline terminal slt = single line telephone...

  • Page 164

    Issue 4.0 2-124 program 11 : system numbering description use program 11-13 : service code setup (for contact center) to customize the service codes which are used with the contact center feature. You can customize additional service codes in programs 11- 10 ~ 11-12 and 11-14 ~ 11-16. The following ...

  • Page 165

    Issue 4.0 sv9100 programming manual 2-125 conditions none feature cross reference contact center 12 change agent group by supervisor when using service code 669 to change an agent group, the supervisor must enter a 2-digit number for the group. For example, to change to group 4, the entry would be 6...

  • Page 166

    Issue 4.0 2-126 program 11 : system numbering description use program 11-14 : service code setup (for hotel) to customize the service codes which are used with the hotel/motel feature. You can customize additional service codes in programs 11-10 ~ 11-13, 11-15 and 11-16. The service codes can be use...

  • Page 167

    Issue 4.0 sv9100 programming manual 2-127 conditions none feature cross reference hotel/motel 14 room status change for own extension mlt, slt 640 15 room status change for other extension mlt, slt 641 16 room status output mlt 642 17 hotel room monitor mlt, slt 675 18 set hotel pms code restriction...

  • Page 168

    Issue 4.0 2-128 program 11 : system numbering description use program 11-15 : service code setup, administrative (for special access) to customize the special access service codes which are used by the administrator in the hotel/motel feature. You can customize additional service codes in programs 1...

  • Page 169

    Issue 4.0 sv9100 programming manual 2-129 conditions none feature cross reference hotel/motel 10 --- not used --- 11 ethernet port reset 12 extension data swap mlt 92-04 13 remote access from disa slt no setting 22-02 14 modem access 740 16 outbound ip connection no setting 90-69 mlt = multiline ter...

  • Page 170

    Issue 4.0 2-130 program 11 : system numbering description use program 11-16 : single digit service code setup to customize the one-digit service codes used when a busy or ring back signal is heard. You can customize additional service codes in programs 11-10 ~ 11-15. The following chart shows: the n...

  • Page 171

    Issue 4.0 sv9100 programming manual 2-131 conditions none feature cross reference refer to the input data chart on previous pages..

  • Page 172: 11-17 : Group Pilot Number

    Issue 4.0 2-132 program 11 : system numbering description use program 11-17 : group pilot number to assign the master number for each group. This is the number a user dials to transfer calls to the group. Normally, you should use unassigned extension numbers (e.G., 500) for the master number. If you...

  • Page 173

    Issue 4.0 sv9100 programming manual 2-133 description use program 11-19: remote conference group pilot number to assign the remote conference pilot number for each remote conference group. This is the number a user dials to call into the remote conference. You must use unassigned extension numbers (...

  • Page 174

    Issue 4.0 2-134 program 11 : system numbering description use program 11-20 : dial extension analyze table to define the dial type based on three or more digits. This program is relevant only if digits in 11-01-01 are set to 9 (dial extension analyze). Default dial extension analyze tables are not s...

  • Page 175

    Sv9100 programming manual 2-135 program: 12 description use program 12-01 : night mode function setup to set up the night mode options. Refer to the following chart for a description of each option, its range and default setting. Conditions none feature cross reference night service program 12 : nig...

  • Page 176

    Issue 4.0 2-136 program 12 : night mode setup description use program 12-02 : automatic night service patterns to define the daily pattern of the automatic mode switching. Each mode group has 10 patterns. These patterns are used in programs 12-03 and 12-04. The daily pattern consists of 20 timer set...

  • Page 177

    Issue 4.0 sv9100 programming manual 2-137 time pattern 2 default all groups, all patterns : 00:00 to 00:00 = mode 1 time pattern 1 time pattern 2 time pattern 3~10 conditions none feature cross reference night service time setting 07: 22:00 to 00:00 mode 3 (midnight) 0:00 0:00 mode 2 (night) time se...

  • Page 178

    Issue 4.0 2-138 program 12 : night mode setup description use program 12-03 : weekly night service switching to define a weekly schedule of night-switch settings. Default program 12 : night mode setup 12-03 : weekly night service switching level: sa input data night mode service group number 01~32 i...

  • Page 179

    Issue 4.0 sv9100 programming manual 2-139 conditions none feature cross reference night service.

  • Page 180

    Issue 4.0 2-140 program 12 : night mode setup description use program 12-04 : holiday night service switching to define a yearly schedule of holiday night- switch settings. This schedule is used for the setting of special days when the company is expected to be closed, such as a national holiday. De...

  • Page 181

    Issue 4.0 sv9100 programming manual 2-141 description use program 12-05 : night mode group assignment for extensions to assign a day/night mode group for each extension. Conditions none feature cross reference night service program 12 : night mode setup 12-05 : night mode group assignment for extens...

  • Page 182

    Issue 4.0 2-142 program 12 : night mode setup description use program 12-06 : night mode group assignment for trunks to assign a day/night mode group for each trunk port. Conditions none feature cross reference night service program 12 : night mode setup 12-06 : night mode group assignment for trunk...

  • Page 183

    Issue 4.0 sv9100 programming manual 2-143 description use program 12-07 : text data for night mode to make an original text message which is displayed on an lcd of multiline telephone in each mode. Default mode 1 = no setting mode 2 = mode 3 = mode 4 = mode 5 = mode 6 = mode 7 = mode 8 = conditions ...

  • Page 184

    Issue 4.0 2-144 program 12 : night mode setup feature cross reference night service.

  • Page 185

    Issue 4.0 sv9100 programming manual 2-145 description use program 12-08 : night mode service range to define the changing range of toggle key for each day/night mode. Example: when program 12-08 is set to 3 and the mode key is pressed (sc 751, 09 +0), the following modes are switched: press once = n...

  • Page 186

    Issue 4.0 2-146 program 12 : night mode setup.

  • Page 187

    Sv9100 programming manual 2-147 program: 13 description use program 13-01 : speed dialing function setup to define the speed dialing functions. Conditions none feature cross reference speed dial – system/group/station program 13 : abbreviated dialing 13-01 : speed dialing function setup level: sa in...

  • Page 188

    Issue 4.0 2-148 program 13 : abbreviated dialing description use program 13-02 : group speed dialing bins to define the range of bin numbers to be used by each speed dialing group. (refer to 13-03 : speed dialing group assignment for extensions ). Default no setting conditions none feature cross ref...

  • Page 189

    Issue 4.0 sv9100 programming manual 2-149 description use program 13-03 : speed dialing group assignment for extensions to assign speed dialing group for each extension. There are 64 available speed dialing groups. Conditions none feature cross reference speed dial - system/group/station program 13 ...

  • Page 190

    Issue 4.0 2-150 program 13 : abbreviated dialing description use program 13-04 : speed dialing number and name to store speed dialing data in the speed dialing areas. This program is also used to define the names assigned to the speed dialing numbers. Program 13 : abbreviated dialing 13-04 : speed d...

  • Page 191

    Issue 4.0 sv9100 programming manual 2-151 05 incoming ring pattern incoming ring pattern 0 = normal pattern 1 ~ 4 = tone pattern (1~4) 5 ~ 9 = scale pattern (1~5) 10 ~ 13 = tone pattern (5~8) 0 13-04-03 08 memo 1 define memo display information tied to common speed dial bin or telephone book which m...

  • Page 192

    Issue 4.0 2-152 program 13 : abbreviated dialing conditions none feature cross reference speed dial – system/group/station.

  • Page 193

    Issue 4.0 sv9100 programming manual 2-153 description use program 13-05 : speed dialing trunk group to define the trunk group/route number to be seized for each speed dialing number. If this program has an entry of 0 (no setting), then seizing a line follows the trunk access group routing of the cal...

  • Page 194

    Issue 4.0 2-154 program 13 : abbreviated dialing description use program 13-07 : telephone book dial number and name to set up the dial number and name of each telephone book number. Conditions none feature cross reference none program 13 : abbreviated dialing 13-07 : telephone book dial number and ...

  • Page 195

    Issue 4.0 sv9100 programming manual 2-155 description use program 13-08 : telephone book system name to set up the name of the telephone book. Conditions none feature cross reference none program 13 : abbreviated dialing 13-08 : telephone book system name level: sb input data telephone book number 0...

  • Page 196

    Issue 4.0 2-156 program 13 : abbreviated dialing description use program 13-09 : telephone book group name to set up the group name of the telephone book. Conditions none feature cross reference none program 13 : abbreviated dialing 13-09 : telephone book group name level: sb input data telephone bo...

  • Page 197

    Issue 4.0 sv9100 programming manual 2-157 description use program 13-10 : telephone book routing to set up outgoing mode when using the telephone book. Trunk outgoing mode follows program 14-06 setting. Conditions none feature cross reference none program 13 : abbreviated dialing 13-10 : telephone b...

  • Page 198

    Issue 4.0 2-158 program 13 : abbreviated dialing.

  • Page 199

    Sv9100 programming manual 2-159 program: 14 description use program 14-01 : basic trunk data setup to set the basic options for each trunk port. Refer to the table below for a description of each option, its range and default setting. Program 14 : trunk, basic setup 14-01 : basic trunk data setup le...

  • Page 200

    Issue 4.0 2-160 program 14 : trunk, basic setup 06 smdr printout include/exclude the trunk you are programming from the smdr printout. Refer to program 35-01 and 35-02 for smdr printout options. 0 = no print out 1 = prints out 0 35-01 35-02 07 outgoing calls allow/prevent outgoing calls on the trunk...

  • Page 201

    Issue 4.0 sv9100 programming manual 2-161 16 forced release of held call enable/disable forced release for calls on hold. If enabled, the system disconnects a call if it is on hold longer than a programmed interval (program 24-01-05). If disabled, forced disconnection does not occur. Program 24-01-0...

  • Page 202

    Issue 4.0 2-162 program 14 : trunk, basic setup 24 trunk-to-trunk outgoing caller id through mode enable/disable the ability to send the original caller id through when the call is forward off-premise. 0 = disable (no) 1 = enable (yes) 0 25 continued/discontinued trunk-to-trunk conversation enable/d...

  • Page 203

    Issue 4.0 sv9100 programming manual 2-163 38 outgoing cli selection select cli (calling party number) sending way to trunk. When set to 0, extension cli number set in prg21-13-01, prg21-18-01, or prg21-19-01is sent according to seized trunk type (isdn/h.323/sip) automatically. When set to 1, calling...

  • Page 204

    Issue 4.0 2-164 program 14 : trunk, basic setup default conditions none feature cross reference refer to features in the input data table. Trunk port number name 1 line 001 2 line 002 : : 400 line 400

  • Page 205

    Issue 4.0 sv9100 programming manual 2-165 description use program 14-02 : analog trunk data setup to set the basic options for each analog trunk port. Refer to the table below for a description of each option, its range and default setting. Program 14 : trunk, basic setup 14-02 : analog trunk data s...

  • Page 206

    Issue 4.0 2-166 program 14 : trunk, basic setup 07 dp to dtmf conversion options determine how a user can convert a dial pulse (dp) call to a dtmf call. For each trunk, set the type of dp to dtmf conversion required. There are three conversion options: automatic (0), automatic and manual (1), or man...

  • Page 207

    Issue 4.0 sv9100 programming manual 2-167 conditions none feature cross reference none 17 sync. Ringing specify whether or not co/pbx calls follow synchronous ringing. Synchronous ringing does not apply to incoming did calls, off-hook ringing calls, or co/pbx ring transfer calls. 0 = disable 1 = ena...

  • Page 208: 14-04 : Behind Pbx Setup

    Issue 4.0 2-168 program 14 : trunk, basic setup description use program 14-04 : behind pbx setup to indicate if the trunk is installed behind a pbx. There is one item for each mode. Conditions none feature cross reference central office calls, placing program 14 : trunk, basic setup 14-04 : behind p...

  • Page 209: 14-05 : Trunk Group

    Issue 4.0 sv9100 programming manual 2-169 description use program 14-05 : trunk group to assign trunks to trunk groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in the outbound priority e...

  • Page 210: 14-06 : Trunk Group Routing

    Issue 4.0 2-170 program 14 : trunk, basic setup description use program 14-06 : trunk group routing to set up an outbound routing table for the trunk groups you assigned in program 14-05. When a user dials 9, the system routes their calls in the order (priority) specified. For example, if a user dia...

  • Page 211

    Issue 4.0 sv9100 programming manual 2-171 default route 1, order number 1 = 1 (trunk group 1). Order numbers 2, 3, 4 = 0 (not specified). All other routes (2~100) and order numbers (1~4) = 0 (not specified). Conditions none feature cross reference none input data route table number 001~100 item no. ...

  • Page 212

    Issue 4.0 2-172 program 14 : trunk, basic setup description use program 14-07 : trunk access map setup to set up the trunk access maps. This sets an extension access options for trunks. For example, an extension can place only outgoing calls on trunks to which it has outgoing access. There are 400 a...

  • Page 213

    Issue 4.0 sv9100 programming manual 2-173 conditions none feature cross reference central office calls, answering central office calls, placing.

  • Page 214

    Issue 4.0 2-174 program 14 : trunk, basic setup description use program 14-08 : music on hold source for trunks to define a music on hold source for a trunk as either the aci or coi port. Conditions none feature cross reference music on hold program 14 : trunk, basic setup 14-08 : music on hold sour...

  • Page 215

    Issue 4.0 sv9100 programming manual 2-175 description use program 14-09 : conversation recording destination for trunks to set the aci conversation recording destination for each trunk. Conditions none feature cross reference analog communications interface (aci) program 14 : trunk, basic setup 14-0...

  • Page 216

    Issue 4.0 2-176 program 14 : trunk, basic setup description use program 14-11 : id setup for ip trunk to set the id of each ip trunk. This program refers to incoming and outgoing ip trunk calls. The id is sent on an outgoing ip trunk call. This program is used only for h.323. Conditions this data is...

  • Page 217

    Issue 4.0 sv9100 programming manual 2-177 description use program 14-12 : sip register id setup for ip trunk to define the sip register id for ip trunks. Conditions none feature cross reference none program 14 : trunk, basic setup 14-12 : sip register id setup for ip trunk level: in input data trunk...

  • Page 218: 14-13 : Ccis System Route Id

    Issue 4.0 2-178 program 14 : trunk, basic setup description use program 14-13 : ccis system route id to define the ccis route id to the trunk group used for k- ccis. Conditions not used for ip-ccis feature cross reference key-common channel interoffice signaling (k-ccis) program 14 : trunk, basic se...

  • Page 219

    Issue 4.0 sv9100 programming manual 2-179 description use program 14-14 : ccis trunk cic assignment to define the cic (circuit identifier code) to each voice channel (trunk port) used for k-ccis. Conditions cic numbers must be assigned consecutively for k-ccis to operate correctly. The d-channel tru...

  • Page 220: 14-18 : Ip Trunk Data Setup

    Issue 4.0 2-180 program 14 : trunk, basic setup description use program 14-18 : ip trunk data setup to define the basic setting of each ip trunk. Program 14 : trunk, basic setup 14-18 : ip trunk data setup level: in input data trunk port number 001~400 item no. Item input data default 01 ip trunk ty...

  • Page 221

    Issue 4.0 sv9100 programming manual 2-181 conditions none feature cross reference none.

  • Page 222

    Issue 4.0 2-182 program 14 : trunk, basic setup.

  • Page 223

    Sv9100 programming manual 2-183 program: 15 description use program 15-01 : basic extension data setup to define the basic settings for each extension. Program 15 : extension, basic setup 15-01 : basic extension data setup level: sa input data extension number 001 ~ 960 item no. Item input data defa...

  • Page 224

    Issue 4.0 2-184 program 15 : extension, basic setup 05 restriction for outgoing disable on incoming line enable/disable supervised dial detection for an extension. 0 = no 1 = yes 0 21-01-15 21-01-16 21-01-17 80-03-01 07 do-not-call 0 = off 1 = on 0 21-01-19 08 call attendant busy message 0~100 (0 = ...

  • Page 225

    Issue 4.0 sv9100 programming manual 2-185 conditions none feature cross reference none.

  • Page 226

    Issue 4.0 2-186 program 15 : extension, basic setup description use program 15-02 : multiline telephone basic data setup to set up various multiline telephone options. Program 15 : extension, basic setup 15-02 : multiline telephone basic data setup level: in input data extension number 001 ~ 960 ite...

  • Page 227

    Issue 4.0 sv9100 programming manual 2-187 03 extension ring tone set the tone (pitch) of the incoming extension call ring for the extension port you are programming. Also refer to program 15-08. 1 = high 2 = medium 3 = low 4 = ring tone 1 5 = ring tone 2 6 = ring tone 3 7 = ring tone 4 8 = ring tone...

  • Page 228

    Issue 4.0 2-188 program 15 : extension, basic setup 11 callback automatic answer enable/disable automatic answer of calls recalling to a station. For example, if a transfer recall or hold recall is ringing back to a station, the following happens: if prg 15-02-11 is enabled, the station automaticall...

  • Page 229

    Issue 4.0 sv9100 programming manual 2-189 21 virtual extension access mode (when idle virtual extension key pressed) determine whether a virtual extension/call arrival key(car) should function as a dss key, a virtual extension, or a car key. When dss (0) is selected, the key functions as a dss key t...

  • Page 230

    Issue 4.0 2-190 program 15 : extension, basic setup 26 msg key operation mode determine whether an extension msg key should function as a message key or voice mail key. If set as a message key, users can press the key to call the voice mail only when they have new messages. 0 = message key 1 = voice...

  • Page 231

    Issue 4.0 sv9100 programming manual 2-191 36 message waiting lamp cycle for called extension select the cycle method that the large led flashes when the extension has message waiting set to the extension. 1 = cycle 1 2 = cycle 2 3 = cycle 3 4 = cycle 4 5 = cycle 5 6 = cycle 6 7 = cycle 7 3 15-02-28 ...

  • Page 232

    Issue 4.0 2-192 program 15 : extension, basic setup 45 double height character indication on the dt800/dt700/dt400/ dt300 style phones name and number line (2), calender line (1) or no line (0) set to has double height characters. 0 = normal indication 1 = double height character indication of calen...

  • Page 233

    Issue 4.0 sv9100 programming manual 2-193 69 microphone operation on handsfree select the microphone status when starting handsfree mode. 0 = no change for mic status 1 = start from mic enabled 2 = start from mic muted 0 70 mic key operation control whether the microphone key is enabled (0) or disab...

  • Page 234

    Issue 4.0 2-194 program 15 : extension, basic setup conditions none feature cross reference refer to the input data chart. 4 cycle 4 125ms – on / 125ms – off / 125ms – on / 625ms – off 5 cycle 5 875ms – on / 125ms – off 6 cycle 6 625ms – on / 125ms – off / 125ms – on / 125ms – off 7 cycle 7 1000ms –...

  • Page 235

    Issue 4.0 sv9100 programming manual 2-195 description use program 15-03 : single line telephone basic data setup to set up various single line telephone options. Program 15 : extension, basic setup 15-03 : single line telephone basic data setup level: in input data extension number 001 ~ 960 item no...

  • Page 236

    Issue 4.0 2-196 program 15 : extension, basic setup 06 extension polarity reverse not used in u.S. -- do not change default entry as dtmf issues may arise with voice mail. 0 = disable (off) 1 = enable (on) 0 07 enabled on-hook when holding (slt) 0 = no 1 = yes 1 11-12-45 08 answer on-hook when holdi...

  • Page 237

    Issue 4.0 sv9100 programming manual 2-197 conditions none (1) (2) (3) (4) (5) outgoing call normal idle reverse incoming call call pickup (1) = off-hook (2) = calling/ringing (3) = answer (4) = detect hang up (5) = on-hook normal idle reverse normal idle reverse.

  • Page 238

    Issue 4.0 2-198 program 15 : extension, basic setup feature cross reference single line telephones, analog 500/2500 sets.

  • Page 239

    Issue 4.0 sv9100 programming manual 2-199 description use program 15-05 : ip telephone terminal basic data setup to set up the basic settings for an ip telephone. Program 15 : extension, basic setup 15-05 : ip telephone terminal basic data setup level: in input data extension number 001 ~ 960 item n...

  • Page 240

    Issue 4.0 2-200 program 15 : extension, basic setup 15 codec type 1-type 1 2-type 2 3-type 3 4-type 4 5-type 5 1 assign the codec type of the mlt sip. 84-24-xx 16 authentication password up to 24 characters none assign the authentication password for sip single line telephones. 15-05-01 18 ip duplic...

  • Page 241

    Issue 4.0 sv9100 programming manual 2-201 26 dt800/dt700 terminal type 0 = not set 1 = itl-( )e-1d/ip- ()e-1 2 = itl-( )d-1d/itl- 24bt1d/itl- 4pa- 1d [without 8lki(lcd)-l] 3 = itl-( )d-1d/itl- 24bt1d/itl-24pa- 1d [with 8lki(lcd)- l] 4 = itl-320c-1 5 = softphone 6 = cti 7 = agw 10 = itl-dg-3 11 = itl...

  • Page 242

    Issue 4.0 2-202 program 15 : extension, basic setup 32 ten key pad talkie 0 = off 1 = on 0 33 lan side ip address of terminal 0.0.0.0~255.255.255.255 0.0.0.0 read-only 34 terminal touch panel on/off 0 = off 1 = on 1 select whether the touch screen used on itl-320c-1 (bk) tel can be used (1) or canno...

  • Page 243

    Issue 4.0 sv9100 programming manual 2-203 43 video mode 0 = disable 1 = enable 0 this program is used to select the video function with the standard sip terminal. If the standard sip terminal supports the video function, the sv9100 transfers the video codec in sdp information. 44 using standard sip ...

  • Page 244

    Issue 4.0 2-204 program 15 : extension, basic setup conditions 15-05-04 – nickname must be unique in the system. Feature cross reference none 48 subscribe expire timer for nat 0 = disable 60 ~ 65535(sec) 180 on a per station basis, this setting defines the sip subscribe expiry timer. If this value i...

  • Page 245

    Issue 4.0 sv9100 programming manual 2-205 description use program 15-06 : trunk access map for extensions to define the trunk access map for each extension. An extension can place only outgoing calls on trunks to which it has outgoing access. Use program 14-07 to define the available access maps. Co...

  • Page 246

    Issue 4.0 2-206 program 15 : extension, basic setup description use program 15-07 : programmable function keys to assign functions to a multiline terminal line keys. For certain functions, you can append data to the key basic function. For example, the function 26 appended by data 1 makes a group ca...

  • Page 247

    Issue 4.0 sv9100 programming manual 2-207 default programmable keys 1~8 are trunk line keys (key 1 = trunk line 1, key 2 = trunk line 2, etc.). All other programmable keys are undefined. Function number list [1] normal function code (00 ~ 99) (service code 751) line key function number additional da...

  • Page 248

    Issue 4.0 2-208 program 15 : extension, basic setup 12 call forward – no answer red on: forwarded 13 call forward – busy/no answer red on: forwarded 14 call forward – both ring red on: forwarded 15 follow me rapid blink (red): forwarded 18 text message setup message numbers (01~20) red on: feature a...

  • Page 249

    Issue 4.0 sv9100 programming manual 2-209 37 dnd/fwd override call none 38 message waiting none 39 room monitoring rapid blink (red): while being monitored slow blink (red): while monitoring 40 handset transmission cutoff red on: transmission cut-off 41 buzzer extension number red on: transmission s...

  • Page 250

    Issue 4.0 2-210 program 15 : extension, basic setup 58 automatic transfer at department group call extension group number ( 01~64) blink (red): active 59 delayed transfer at department group call extension group number (01~64) blink (red): active 60 dnd at department group call extension group numbe...

  • Page 251

    Issue 4.0 sv9100 programming manual 2-211 79 automated attendant (in-skin) extension number or pilot number red on: set up for all calls fast blink (red): set up for no answer calls stutter blink (red): set up for busy calls slow blink (red): set up for busy/no answer calls 80 tandem ringing 1 = set...

  • Page 252

    Issue 4.0 2-212 program 15 : extension, basic setup #04 change restriction class one-time toll restriction #06 power saving for power save group power save group number 00~32 (00 = all groups) on (red): set off: cancel #07 fixed operation mode night mode service group no. (01~32) fast flash (red) : ...

  • Page 253

    Issue 4.0 sv9100 programming manual 2-213 06 trunk access via networking network system number (01~50) 07 station park hold none 08 cap key cap orbit no. (0001~9999) if cap orbit no.0000 is used, the next available orbit is automatically selected. 10 log-in/log-out red on: under log-on off: under lo...

  • Page 254

    Issue 4.0 2-214 program 15 : extension, basic setup 35 system call history on (red) : other using on (red) : using off (green) : not using 36 acd whispering on (red) : when using contact center whispering 37 acd queue alarm display acd group no. (01 ~ 64) on (red) : while displaying queue status fas...

  • Page 255

    Issue 4.0 sv9100 programming manual 2-215 conditions when a key is programmed using service code 752, it cannot be programmed with a function using the 751 code until the key is undefined (000). For example with a park key programmed by dialing 752 + 04 must be undefined by dialing 752 + 000 before ...

  • Page 256

    Issue 4.0 2-216 program 15 : extension, basic setup description use program 15-08 : incoming virtual extension ring tone setup to assign a ring tone range (0~4) to incoming virtual extensions assigned to a virtual extension key (program 15-07). If you enable ringing for the key in program 15-09, the...

  • Page 257

    Issue 4.0 sv9100 programming manual 2-217 conditions none feature cross reference none table 2-6 program 15-08 – incoming signal frequency patterns incoming signal frequency pattern type frequency 1 frequency 2 modulation pattern 1 high middle low 1100 660 520 1400 760 660 16hz 16hz 16hz pattern 2 h...

  • Page 258

    Issue 4.0 2-218 program 15 : extension, basic setup description use program 15-09 : virtual extension ring assignment to assign the ringing options for an extension virtual extension key or virtual extension group answer key which is defined in program 15- 07. You make an assignment for each night s...

  • Page 259

    Issue 4.0 sv9100 programming manual 2-219 description use program 15-10 : incoming virtual extension ring tone order setup to set the priority (1~4) for the virtual extension ring tones set in program 15-08. When virtual extension calls ring an extension simultaneously, the tone with the highest ord...

  • Page 260

    Issue 4.0 2-220 program 15 : extension, basic setup conditions none feature cross reference none.

  • Page 261

    Issue 4.0 sv9100 programming manual 2-221 description use program 15-11 : virtual extension delayed ring assignment to assign the delayed ringing options for an extension virtual extension or virtual extension group answer keys (defined in program 15-09). You make an assignment for each night servic...

  • Page 262

    Issue 4.0 2-222 program 15 : extension, basic setup description use program 15-12 : conversation recording destination for extensions to set the aci conversation recording destination for each extension. Conditions none feature cross reference analog communications interface (aci) program 15 : exten...

  • Page 263: 15-13 : Loop Key Data

    Issue 4.0 sv9100 programming manual 2-223 description use program 15-13 : loop key data to set the loop key data for each terminal. Loop keys can be incoming, outgoing, or both ways. Outgoing loop keys use the entry in item 01. Incoming loop keys use the entry in item 02. Both way loop keys follow t...

  • Page 264

    Issue 4.0 2-224 program 15 : extension, basic setup description use program 15-14 : programmable one-touch keys to define the one-touch key data for each multiline terminal. For each univerge sv9100 wireless telephone to use the transfer when out of range feature, enter the destination number (up to...

  • Page 265

    Issue 4.0 sv9100 programming manual 2-225 description use program 15-16 : sip register setup for extensionto define the sip register id for extensions. Conditions none feature cross reference none program 15 : extension, basic setup 15-16 : sip register id setup for extension level: in input data ex...

  • Page 266

    Issue 4.0 2-226 program 15 : extension, basic setup description use program 15-17 : co message waiting indication to set the message waiting led flash assignment on each co line. Conditions none feature cross reference none program 15 : extension, basic setup 15-17 : co message waiting indication le...

  • Page 267

    Issue 4.0 sv9100 programming manual 2-227 description use program 15-18 : virtual extension key enhanced options to define the operation when a virtual extension key is pressed. Program 15 : extension, basic setup 15-18 : virtual extension key enhanced options level: in input data extension number i...

  • Page 268

    Issue 4.0 2-228 program 15 : extension, basic setup conditions if a trunk call rings a virtual extension, the virtual extension key operation mode must be set to 1 (land on the key), or the multiline terminal must have a cap key or co line appearance. Feature cross reference none 05 one ring when se...

  • Page 269

    Issue 4.0 sv9100 programming manual 2-229 description use program 15-19 : system telephone book setup for extension to set the operations of the telephone book for each extension. Conditions none feature cross reference none program 15 : extension, basic setup 15-19 : system telephone book setup for...

  • Page 270

    Issue 4.0 2-230 program 15 : extension, basic setup description use program 15-20 : lcd line key name assignmentto assigns a name to each lcd line key of the sv9100 telephones and adm option. Up to 13 characters can be assigned. Default settings conditions none feature cross reference none program 1...

  • Page 271

    Issue 4.0 sv9100 programming manual 2-231 description use program 15-22 : mobile extension setup to set the system information for the mobile extension feature. Program 15 : extension, basic setup 15-22 : mobile extension setup level: in input data extension number 001 ~ 960 item no. Item input data...

  • Page 272

    Issue 4.0 2-232 program 15 : extension, basic setup conditions none feature cross reference none.

  • Page 273

    Issue 4.0 sv9100 programming manual 2-233 description use program 15-23 : incoming virtual extension large led setup to set the color of the large led, when the virtual extension rings. Conditions none feature cross reference none program 15 : extension, basic setup 15-23 : incoming virtual extensio...

  • Page 274

    Issue 4.0 2-234 program 15 : extension, basic setup description use program 15-24 : registration of standard sip terminal to register data in the standard sip terminal where register is not used. Program 15 : extension, basic setup 15-24 : registration of standard sip terminal level: in input data e...

  • Page 275

    Issue 4.0 sv9100 programming manual 2-235 conditions none feature cross reference none.

  • Page 276: 15-25 : Desi-Less Page Setup

    Issue 4.0 2-236 program 15 : extension, basic setup description use program 15-25 : desi-less page setup to define the page of each desi-less extension. Conditions none feature cross reference none program 15 : extension, basic setup 15-25 : desi-less page setup level: in input data extension number...

  • Page 277: 15-27 : Power Saving Setup

    Issue 4.0 sv9100 programming manual 2-237 description use program 15-27 : power saving setup to set the power saving mode for extensions. Conditions none feature cross reference none program 15 : extension, basic setup 15-27 : power saving setup level: in input data extension number 001 ~ 960 item n...

  • Page 278

    Issue 4.0 2-238 program 15 : extension, basic setup description use program 15-29 : setting of function key for bth handset to make the relationship of function keys between the bth and the desk terminal. Conditions multiple bth keys cannot be assigned with the same desk terminal key in prg 15-29-01...

  • Page 279

    Issue 4.0 sv9100 programming manual 2-239.

  • Page 280

    Issue 4.0 2-240 program 15 : extension, basic setup.

  • Page 281

    Sv9100 programming manual 2-241 program: 16 description use program 16-01 : department group basic data setup to set the function mode for each department group. There are 64 available department groups. Program 16 : department group setup 16-01 : department group basic data setup level: in input da...

  • Page 282

    Issue 4.0 2-242 program 16 : department group setup conditions none feature cross reference department calling 05 extension group all ring mode operation determine whether calls ringing a department group should ring all extensions in the group simultaneously automatically or manually when using the...

  • Page 283

    Issue 4.0 sv9100 programming manual 2-243 description use program 16-02 : department group assignment for extensions to set the department groups. The system uses these groups (64 department groups) for department calling. Assign pilot numbers to department groups you set up in program 11-07. This l...

  • Page 284

    Issue 4.0 2-244 program 16 : department group setup description use program 16-03 : secondary department group to set a second department group for extensions. Up to 16 extensions can be assigned per department group. There are 64 available department groups. Default all extension groups : no settin...

  • Page 285

    Issue 4.0 sv9100 programming manual 2-245 description use program 16-04 : call restriction between department groups to set internal calls between members of different department (station) groups that can be restricted per group. Each department group can restrict calls to up to eight department gro...

  • Page 286

    Issue 4.0 2-246 program 16 : department group setup.

  • Page 287: 20-01 : System Options

    Sv9100 programming manual 2-247 program: 20 description use program 20-01 : system options to set various system options. Program 20 : system option setup 20-01 : system options level: in input data item no. Item input data default description related program 01 operator access mode 0 = step call 1 ...

  • Page 288

    Issue 4.0 2-248 program 20 : system option setup conditions none feature cross reference refer to the input data table at the beginning of this section. 16 mobile extension callback duration time 1~64800(sec) 15 set up the system callback duration time when ringing the target mobile extension. 15-22...

  • Page 289

    Issue 4.0 sv9100 programming manual 2-249 description use program 20-02 : system options for multiline telephones to set various system options for multiline telephones. Program 20 : system option setup 20-02 : system options for multiline telephones level: in input data item no. Item input data def...

  • Page 290

    Issue 4.0 2-250 program 20 : system option setup 06 preselection time when a multiline terminal user preselects a line key, the system remembers the preselection for this time. 0~64800 (sec) 5 07 time and date display mode set how the time and date appear on display telephones. There are eight displ...

  • Page 291

    Issue 4.0 sv9100 programming manual 2-251 conditions none feature cross reference none 15 caller id display mode 0 = name and number (both) 1 = name 2 = number 0 18 dialing record display time 0~64800 seconds 30 19 virtual extension mode set the mode of a virtual extension key that appears on a dss ...

  • Page 292

    Issue 4.0 2-252 program 20 : system option setup description use program 20-03 : system options for single line telephones to set up various options for single line telephones. Program 20 : system option setup 20-03 : system options for single line telephones level: in input data item no. Item input...

  • Page 293

    Issue 4.0 sv9100 programming manual 2-253 conditions none feature cross reference single line telephones, analog 500/2500 sets 04 dial sending start time for slt or ars when ars or an analog extension user accesses a trunk and dials an outside call, the system waits this time before outdialing the f...

  • Page 294

    Issue 4.0 2-254 program 20 : system option setup description use program 20-04 : system options for virtual extensions to set up various system options for virtual extensions. There are 512 available virtual extension ports. Conditions none feature cross reference call arrival (car) keys (car/second...

  • Page 295

    Issue 4.0 sv9100 programming manual 2-255 description use program 20-06 : class of service for extensions to assign a class of service (cos) to an extension. There are 15 classes of service that can be assigned. To specify the options in each class of service, refer to programs 20-07 through 20-13. ...

  • Page 296

    Issue 4.0 2-256 program 20 : system option setup description use program 20-07 : class of service options (administrator level) to define the administrator service availability for each extension class of service (cos). Program 20 : system option setup 20-07 : class of service options (administrator...

  • Page 297

    Issue 4.0 sv9100 programming manual 2-257 10 programmable function key programming (appearance level) turn off or on an extension user ability to program the appearance function keys using service code 752. 0 = off 1 = on 1 1 11-11-38 20-13-18 11 forced trunk disconnect (analog trunk only) turn off ...

  • Page 298

    Issue 4.0 2-258 program 20 : system option setup conditions none feature cross reference class of service 26 dial-in mode switch 0 = off 1 = on 0 0 11-10-35 27 do-not-call administrator 0 = off 1 = on 0 0 25-01-07 15-07-89 20-01-19 28 --- not used --- 30 date setting 0 = off 1 = on 1 1 11-10-41 34 c...

  • Page 299

    Issue 4.0 sv9100 programming manual 2-259 description use program 20-08 : class of service options (outgoing call service) to define the outgoing call feature availability for each extension class of service (cos). Program 20 : system option setup 20-08 : class of service options (outgoing call serv...

  • Page 300

    Issue 4.0 2-260 program 20 : system option setup 08 toll restriction dial block turn off or on an extension ability to use dial block. 0 = off 1 = on 0 0 09 hotline/extension ringdown turn off or on ringdown extension for extensions with this cos. 0 = off 1 = on 0 0 10 signal/voice call turn off or ...

  • Page 301

    Issue 4.0 sv9100 programming manual 2-261 conditions none feature cross reference class of service 20 hot key pad set the ability of an extension user to make a call by dialing the number without first going off hook. 0 = off 1 = on 0 0 21 automatic trunk seizing by pressing spk key turn off or on a...

  • Page 302

    Issue 4.0 2-262 program 20 : system option setup description use program 20-09 : class of service options (incoming call service) to define the incoming call feature availability for each extension class of service (cos). Program 20 : system option setup 20-09 : class of service options (incoming ca...

  • Page 303

    Issue 4.0 sv9100 programming manual 2-263 conditions none feature cross reference class of service 05 signal/voice call turn off or on an extension user ability to enable handsfree answerback or forced intercom ringing for their incoming intercom calls. 0 = off 1 = on 1 1 11-11-15, 11-11-16 06 incom...

  • Page 304

    Issue 4.0 2-264 program 20 : system option setup description use program 20-10 : class of service options (answer service) to define the answer feature availability for each extension class of service (cos). Program 20 : system option setup 20-10 : class of service options (answer service) level: in...

  • Page 305

    Issue 4.0 sv9100 programming manual 2-265 conditions none feature cross reference none 08 virtual extension off-hook answer turn off or on an extension ability to answer an incoming call on a call arrival (car)/secondary incoming extension (sie)/virtual extension simply by lifting the handset. 0 = o...

  • Page 306

    Issue 4.0 2-266 program 20 : system option setup description use program 20-11 : class of service options (hold/transfer service) to define the hold and transfer feature availability for each extension class of service (cos). Program 20 : system option setup 20-11 : class of service options (hold/tr...

  • Page 307

    Issue 4.0 sv9100 programming manual 2-267 08 transfer information display turn off or on an extension ability for incoming transfer preanswer display. 0 = off 1 = on 1 1 09 group hold initiate turn off or on an extension user ability to initiate a group hold. 0 = off 1 = on 1 1 10 group hold answer ...

  • Page 308

    Issue 4.0 2-268 program 20 : system option setup 18 no recall when set to a (0) off, unanswered transferred calls will recall to the station that performed the transfer once the transfer recall timer expires. When set to a (1) on, unanswered transferred calls will not recall to the station that perf...

  • Page 309

    Issue 4.0 sv9100 programming manual 2-269 conditions none feature cross reference class of service 28 both ring enhancement 0 = normal (default) rings on other extension when the other paired extension is busy (not idle). 1 = enhanced does not ring other extension when the other paired extension is ...

  • Page 310

    Issue 4.0 2-270 program 20 : system option setup description use program 20-12 : class of service options (charging cost service) to define the charging cost service availability for each extension service class. Conditions none feature cross reference class of service program 20 : system option set...

  • Page 311

    Issue 4.0 sv9100 programming manual 2-271 description use program 20-13 : class of service options (supplementary service) to define the supplementary feature availability for each extension class of service (cos). Program 20 : system option setup 20-13 : class of service options (supplementary serv...

  • Page 312

    Issue 4.0 2-272 program 20 : system option setup 08 conference turn off or on an extension user ability to initiate a conference or meet-me conference. 0 = off 1 = on 1 1 09 privacy release turn off or on an extension user ability to initiate a voice call conference. 0 = off 1 = on 1 1 10 barge-in m...

  • Page 313

    Issue 4.0 sv9100 programming manual 2-273 19 selectable display messaging (text messaging) turn off or on an extension user ability to use selectable display messaging. 0 = off 1 = on 1 1 20 account code/toll restriction operator alert (restricted operation transfer) turn off or on operator alert wh...

  • Page 314

    Issue 4.0 2-274 program 20 : system option setup 31 connected line identification (colp) 0 = off 1 = on 0 0 32 deny multiple barge-ins allow/deny an extension user from having multiple users barge into their conversation. 0 = off 1 = on 0 0 33 supervisor’s position enhancement this option must be se...

  • Page 315

    Issue 4.0 sv9100 programming manual 2-275 conditions none feature cross reference class of service 45 mic key mode while call monitoring set per class of service, when in call monitoring mode determines if the monitored parties receive the barge in alert tone when coaching mode is enabled. 0 = enabl...

  • Page 316

    Issue 4.0 2-276 program 20 : system option setup description use program 20-14 : class of service options for disa/e&m to enable/disable disa and tie line class of service options. You assign a disa class of service to disa users in program 25-09. Assign tie line classes of service in 34-02. Up to 1...

  • Page 317

    Issue 4.0 sv9100 programming manual 2-277 conditions none feature cross reference class of service direct inward system access (disa) tie lines 06 internal paging enable/disable a disa or tie trunk caller ability to use the telephone system internal paging. 0 = off 1 = on 1 07 external paging enable...

  • Page 318: 20-15 : Ring Cycle Setup

    Issue 4.0 2-278 program 20 : system option setup description use program 20-15 : ring cycle setup to define the ringing cycles for each ring type. Program 20 : system option setup 20-15 : ring cycle setup level: in input data item no. Incoming signal type ringing cycle default 01 normal incoming cal...

  • Page 319

    Issue 4.0 sv9100 programming manual 2-279 conditions none feature cross reference none number ringing cycle 1 on 2 on:2.0 / off:4.0 3 on:1.0 / off:2.0 4 on:0.5 / off:0.5 5 on:0.25 / off:0.25 6 on:0.5 / off:0.5 / on:0.5 / off:1.5 7 on:0.25 / off:0.25 / on:0.25 / off:5.25 8 on:0.375 / off:0.25 / on:0....

  • Page 320

    Issue 4.0 2-280 program 20 : system option setup description use program 20-16 : selectable display messages to enter the selectable display messages. There are 20 alphanumeric messages, with up to 24 characters. Use the following chart when programming messages. Program 20 : system option setup 20-...

  • Page 321

    Issue 4.0 sv9100 programming manual 2-281 when using dtp or dtu style telephones on the univerge sv9100 system, not all the same characters are available. Input data selectable display message number 01~20 item no. Input data 01 24 characters number message 1 in meeting until ##:## 2 meeting room – ...

  • Page 322

    Issue 4.0 2-282 program 20 : system option setup conditions time value ## : ## must be followed by two spaces. Feature cross reference selectable display messages.

  • Page 323: 20-17 : Operator Extension

    Issue 4.0 sv9100 programming manual 2-283 description use program 20-17 : operator extension to designate an operator. When an extension user dials 0 or 9 (defined by program 11-01 type 5), calls go to the operator selected in this program. If you do not assign an extension in program 90-11-01, syst...

  • Page 324: 20-18 : Service Tone Timers

    Issue 4.0 2-284 program 20 : system option setup description use program 20-18 : service tone timers to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Program 20 : system option setup 20-18 : service to...

  • Page 325

    Issue 4.0 sv9100 programming manual 2-285 conditions none feature cross reference distinctive ringing, tones, and flash patterns.

  • Page 326

    Issue 4.0 2-286 program 20 : system option setup description use program 20-19 : system options for caller id to define the system options for the caller id feature. Program 20 : system option setup 20-19 : system options for caller id level: in input data item no. Item input data default 01 caller ...

  • Page 327

    Issue 4.0 sv9100 programming manual 2-287 conditions edit caller id works when program 20-19-07 and program 20-19-08 are set. Calling party name for isdn trunk works when program 14-01-24 and program 15-01-01 are set. Feature cross reference caller id.

  • Page 328

    Issue 4.0 2-288 program 20 : system option setup description use program 20-20 : message setup for non-caller id data to define the messages which are displayed when no caller id information is received. Conditions none feature cross reference caller id program 20 : system option setup 20-20 : messa...

  • Page 329

    Issue 4.0 sv9100 programming manual 2-289 description use program 20-21 : system options for long conversation to define the system options for the long conversation feature. Conditions none feature cross reference long conversation cutoff program 20 : system option setup 20-21 : system options for ...

  • Page 330

    Issue 4.0 2-290 program 20 : system option setup description use program 20-22 : system options for wireless – dect service to define the time the system waits before determining the wireless – dect phone is out of range. For incoming calls, the time begins when the call is received. If the time def...

  • Page 331

    Issue 4.0 sv9100 programming manual 2-291 description use program 20-23 : system options for cti to define the system options for the cti feature. Conditions none feature cross reference computer telephony integration (cti) applications program 20 : system option setup 20-23 : system options for cti...

  • Page 332: 20-25 : Isdn Options

    Issue 4.0 2-292 program 20 : system option setup description use program 20-25 : isdn options to define the isdn system options. Program 20 : system option setup 20-25 : isdn options level: in input data item no. Item input data default 01 send the release message after subscriber hangs up 0 = off 1...

  • Page 333

    Issue 4.0 sv9100 programming manual 2-293 conditions none feature cross reference isdn compatibility 12 call forward options (auto connect send) incoming calls forwarded out automatically return connect message when outgoing call receives alerting message. 0 = normal – no message (off) 1 = normal – ...

  • Page 334

    Issue 4.0 2-294 program 20 : system option setup description use program 20-26 : multiplier changing co to define the multiplier for charging cost to each extension service class. Conditions none feature cross reference none program 20 : system option setup 20-26 : multiplier changing co level: in i...

  • Page 335

    Issue 4.0 sv9100 programming manual 2-295 description use program 20-28 : trunk to trunk conversation to define system options for trunk to trunk conversation. Conditions none feature cross reference none program 20 : system option setup 20-28 : trunk to trunk conversation level: in input data item ...

  • Page 336

    Issue 4.0 2-296 program 20 : system option setup description use program 20-29 : timer class for extension to assign the timer class to each extension. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. This entry includes virtual ext...

  • Page 337

    Issue 4.0 sv9100 programming manual 2-297 description use program 20-30 : timer class for trunks to assign the timer class to each trunk. There are 16 classes that can be assigned. You make eight entries for this program, one for each night service mode. The details of classes are assigned by progra...

  • Page 338

    Issue 4.0 2-298 program 20 : system option setup description use program 20-31 : timer class timer assignment to assign values to the timers on a class of service basis. Program 20 : system option setup 20-31 : timer class timer assignment level: in input data timer class number 1~15 item no. Item i...

  • Page 339

    Issue 4.0 sv9100 programming manual 2-299 07 ring no answer alarm time if a trunk rings a multiline telephone longer than this time, the system changes the ring cadence. This indicates to the user that the call has been ringing too long. 0~64800 seconds 60 seconds 22-01-03 08 dil/incoming ring group...

  • Page 340

    Issue 4.0 2-300 program 20 : system option setup 16 transfer recall time an unanswered transferred call recalls after this time to the extension that initially transferred it. 0~64800 seconds 30 seconds 24-02-04 17 vrs/disa no answer time (disconnect or irg or vm) a vrs/disa caller can ring an exten...

  • Page 341

    Issue 4.0 sv9100 programming manual 2-301 conditions these timers are used when an extension or trunk is assigned to a class from 1 to 15 in 20-29-01 or 20-30-01. When the timer class is set to 0, the system-wide timer is used. All defaults are the same as the system-wide timers. Feature cross refer...

  • Page 342

    Issue 4.0 2-302 program 20 : system option setup description use program 20-34: remote conference group setting to configure remote conference parameters. Program 20 : system option setup 20-34 : remote conference group setting level: in input data item no. Item input data default 01 remote conferen...

  • Page 343

    Issue 4.0 sv9100 programming manual 2-303 conditions none feature cross reference none 08 conference group setup - automatic recording enable or disable automatic recording for a remote conference. If disabled, a line key must be used to start recording. 0 = disable 1 = enable 0 09 conference group ...

  • Page 344

    Issue 4.0 2-304 program 20 : system option setup description use program 20-35 : extension’s operator setting to assign an extension to an operator group. Conditions none feature cross reference none program 20 : system option setup 20-35 : extension’s operator setting level: in input data extension...

  • Page 345

    Issue 4.0 sv9100 programming manual 2-305 description use program 20-36 : trunk’s operator setting to assign a trunk to an operator group. Conditions none feature cross reference none program 20 : system option setup 20-36 : trunk’s operator setting level: in input data trunk port number 001~400 ite...

  • Page 346

    Issue 4.0 2-306 program 20 : system option setup description use program 20-37 : operator extension group setup to define the operator(s) in the operator group. Conditions none feature cross reference none program 20 : system option setup 20-37 : operator extension group setup level: in input data o...

  • Page 347

    Issue 4.0 sv9100 programming manual 2-307 description use program 20-38 : operator group setting to set up priority of a call when calling an operator telephone. Conditions none feature cross reference none program 20 : system option setup 20-38 : operator group setting level: in input data operator...

  • Page 348: 20-44 : Watch Mode Setup

    Issue 4.0 2-308 program 20 : system option setup description use program 20-44 : watch mode setup to set system options for watch message. Conditions none feature cross reference none program 20 : system option setup 20-44 : watch mode setup level: in input data operator group 1~15 item no. Item inp...

  • Page 349: 20-45 : Remote Watch Setup

    Issue 4.0 sv9100 programming manual 2-309 description use program 20-45 : remote watch setup to configure remote monitor settings. Conditions none feature cross reference none program 20 : system option setup 20-45 : remote watch setup level: in input data terminal 1~6 item no. Item input data defau...

  • Page 350

    Issue 4.0 2-310 program 20 : system option setup description use program 20-46 : security sensor setup to set system security sensor options. Program 20 : system option setup 20-46 : security sensor setup level: in input data security sensor number 1~8 item no. Item input data default 01 sensor mode...

  • Page 351

    Issue 4.0 sv9100 programming manual 2-311 conditions none feature cross reference none.

  • Page 352

    Issue 4.0 2-312 program 20 : system option setup description use program 20-47 : time pattern setting for watch mode to assign the watch mode time pattern. Conditions none feature cross reference none program 20 : system option setup 20-47 : time pattern setting for watch mode level: in input data i...

  • Page 353

    Issue 4.0 sv9100 programming manual 2-313 description use program 20-48 : time pattern setting for security sensor to assign the security sensor time pattern. Conditions none feature cross reference none program 20 : system option setup 20-48 : time pattern setting for security sensor level: in inpu...

  • Page 354

    Issue 4.0 2-314 program 20 : system option setup description use program 20-53 : night mode group assignment for power save group to assign the night mode service group number into the power save group. Conditions none feature cross reference none program 20 : system option setup 20-53 : night mode ...

  • Page 355

    Issue 4.0 sv9100 programming manual 2-315 description use program 20-54 : power supply mode for each power save group to assign the power saving mode in each power saving group and night mode. Conditions none feature cross reference none program 20 : system option setup 20-54 : power supply mode for...

  • Page 356

    Issue 4.0 2-316 program 20 : system option setup description use program 20-55 : delay timer for security sensor to set the interval for the sensor delay timer. Conditions none feature cross reference none program 20 : system option setup 20-55 : delay timer for security sensor level: in input data ...

  • Page 357

    Issue 4.0 sv9100 programming manual 2-317 description use program 20-57 : uc user information settings to define the user information settings used in uc. Conditions none feature cross reference none program 20 : system option setup 20-57 : uc user information settings level: in index data user info...

  • Page 358

    Issue 4.0 2-318 program 20 : system option setup description use program 20-58 : uc server presence settings to define the site’s presence states. Program 20 : system option setup 20-58 : uc server presence settings level: in input data item no. Item input data default 01 uc server presence states: ...

  • Page 359

    Issue 4.0 sv9100 programming manual 2-319 conditions none feature cross reference none 14 uc server custom presence 2 definition any characters no setting 15 uc server custom presence 2 use 0 = disable 1 = enable 0 16 uc server custom presence 3 definition any characters no setting 17 uc server cust...

  • Page 360

    Issue 4.0 2-320 program 20 : system option setup description use program 20-59 : server user settings to define uc users and their permissions within the uc client. Program 20 : system option setup 20-59 : uc server user settings level: in index data user settings table number 1 ~ 896 input data ite...

  • Page 361

    Issue 4.0 sv9100 programming manual 2-321 conditions none feature cross reference none 13 uc - server connect 0 = disable 1 = enable 1 14 uc - license level 0 = softphone 1 = deskset 2 = softphone + deskset 1 15 uc - login mode 0 = softphone 1 = deskset 1 16 uc - attendant mode 0 = disable 1 = enabl...

  • Page 362

    Issue 4.0 2-322 program 20 : system option setup description use program 20-60 : uc server telephony settings to define special telephony options for the uc server. Conditions none feature cross reference none program 20 : system option setup 20-60 : uc server telephony settings level: in input data...

  • Page 363

    Issue 4.0 sv9100 programming manual 2-323 description use program 20-61 : uc server call alerts feature settings to define the abandon call alerts settings in the uc server. Conditions none feature cross reference none program 20 : system option setup 20-61 : uc server call alerts feature settings l...

  • Page 364: 20-62 : Uc Exception Table

    Issue 4.0 2-324 program 20 : system option setup description use program 20-62 : uc exception table to set the exception table parameters. Conditions none feature cross reference none program 20 : system option setup 20-62 : uc exception table level: in index data user exception table number 1 ~ 99 ...

  • Page 365

    Issue 4.0 sv9100 programming manual 2-325 description use program 20-64 : uc web application setting to set the uc web application . Conditions none feature cross reference none program 20 : system option setup 20-64 : uc web application setting level: sa input data item no. Item input data default ...

  • Page 366

    Issue 4.0 2-326 program 20 : system option setup description use program 20-65 : multi-device group setup (terminal information) to set the multi-device parameters. Conditions none feature cross reference none program 20 : system option setup 20-65 : multi-device group setup (terminal information) l...

  • Page 367

    Issue 4.0 sv9100 programming manual 2-327 description use program 20-66 : stun/turn server setting to set the stun/turn server parameters. Conditions none feature cross reference none program 20 : system option setup 20-66 : stun/turn server setting level: mf input data item no. Item input data defa...

  • Page 368

    Issue 4.0 2-328 program 20 : system option setup.

  • Page 369

    Sv9100 programming manual 2-329 program: 21 description use program 21-01 : system options for outgoing calls to set the system options for outgoing call service. Program 21 : outgoing call setup 21-01 : system options for outgoing calls level: in input data item no. Item input data default related ...

  • Page 370

    Issue 4.0 2-330 program 21 : outgoing call setup 05 disconnect time when dial tone not detected if 14-02-11 is enabled, the system skips over a trunk if dial tone is not detected. This option pertains to calls placed using speed dial, ars, last number redial or save number dialed. It does not pertai...

  • Page 371

    Issue 4.0 sv9100 programming manual 2-331 12 dial e911 routing without trunk access if enabled (1), an extension user can dial 911 (usa only) without first dialing a trunk access code or pressing a line key. If disabled (0), an extension user must dial a trunk access code (e.G., 9) or press a line k...

  • Page 372

    Issue 4.0 2-332 program 21 : outgoing call setup conditions none feature cross reference central office calls, placing.

  • Page 373

    Issue 4.0 sv9100 programming manual 2-333 description use program 21-02 : trunk group routing for extensions to assign program 14-06 routes to extensions. Conditions none feature cross reference none program 21 : outgoing call setup 21-02 : trunk group routing for extensions level: in input data ext...

  • Page 374

    Issue 4.0 2-334 program 21 : outgoing call setup description use program 21-03 : trunk group routing for trunks to set the trunk route table for automatic external call forward. The route table is set in program 14-06. Conditions none feature cross reference trunk group routing program 21 : outgoing...

  • Page 375

    Issue 4.0 sv9100 programming manual 2-335 description use program 21-04 : toll restriction class for extensions to assign a toll restriction class to an extension. The details of toll restriction are defined in program 21-05 and 21-06. Conditions none feature cross reference none program 21 : outgoi...

  • Page 376

    Issue 4.0 2-336 program 21 : outgoing call setup description use program 21-05 : toll restriction class to set the system toll restriction classes (1~15). Program 21 : outgoing call setup 21-05 : toll restriction class level: in input data toll restriction class number 1~15 item no. Item input data ...

  • Page 377

    Issue 4.0 sv9100 programming manual 2-337 07 permit code table 1~4 = table 0 = disable (none) 1, 2, 6~15 = 0 3 = 1 4 = 2 5 = 3 set the tables 1~4 when referring to the table set up by 21-06-06. 21-06-06 08 restriction table 1~4 = table 0 = disable (none) 1, 2, 6~15 = 0 3 = 1 4 = 2 5 = 3 set the tabl...

  • Page 378

    Issue 4.0 2-338 program 21 : outgoing call setup default conditions none feature cross reference none toll restriction class item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 01: international call restrict table 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 02: international call permit table 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 ...

  • Page 379

    Issue 4.0 sv9100 programming manual 2-339 description use program 21-06 : toll restriction table data setup to set the system toll restriction data. Dial 1~9, 0, , # can be entered in each table. Program 21 : outgoing call setup 21-06 : toll restriction table data setup level: in input data item no....

  • Page 380

    Issue 4.0 2-340 program 21 : outgoing call setup 06 permit code table 1 ~ 4 (table) 001 ~ 200 (entry) dial (up to 12 digits) table 1 ~ 4 = no setting program the permit code tables. If the system has toll restriction enabled, users can dial numbers only if permitted by these tables and the common pe...

  • Page 381

    Issue 4.0 sv9100 programming manual 2-341 conditions none feature cross reference none 10 outgoing call code setup 1 ~ 20 dial (up to four digits) no setting input data (continued) item no. Item table input data default description.

  • Page 382

    Issue 4.0 2-342 program 21 : outgoing call setup description use program 21-07 : toll restriction override password setup to assign toll restriction override codes to extension ports. Each code must have four digits, using any combination of 0~9, # and . Each extension can have a separate code, or m...

  • Page 383: 21-08 : Repeat Dial Setup

    Issue 4.0 sv9100 programming manual 2-343 description use program 21-08 : repeat dial setup to define the automatic repeat dial data. Conditions none feature cross reference none program 21 : outgoing call setup 21-08 : repeat dial setup level: in input data item no. Item input data default 01 repea...

  • Page 384: 21-09 : Dial Block Setup

    Issue 4.0 2-344 program 21 : outgoing call setup description use program 21-09 : dial block setup to define the dial blocking toll restriction class and dial block password to be used by the supervisor extension. Conditions this function works by password and class of service control (the supervisor...

  • Page 385

    Issue 4.0 sv9100 programming manual 2-345 description use program 21-10 : dial block restriction class per extension to define the toll restriction class to each extension when the extension is set for dial block restriction. If this data is 0, toll restriction class follows program 21-09-01. Condit...

  • Page 386

    Issue 4.0 2-346 program 21 : outgoing call setup description use program 21-11 : extension ringdown (hotline) assignment to define the hotline destination number for each extension number. Conditions use the @ code to make an outbound call automatically to a disa trunk or to vm auto attendant. This ...

  • Page 387

    Issue 4.0 sv9100 programming manual 2-347 description use program 21-12 : isdn calling party number setup for trunks to assign calling party numbers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not have an extension calling number assigned (program 21-...

  • Page 388

    Issue 4.0 2-348 program 21 : outgoing call setup description use program 21-13 : isdn calling party number setup for extensions to assign each extension a calling party number (maximum 16 digits per entry). The calling number is the subscriber number of the dial-in number. When a call is made by an ...

  • Page 389

    Issue 4.0 sv9100 programming manual 2-349 description use program 21-14 : walking toll restriction password setup to assign the password and toll restriction class for walking toll restriction. Each code has six digits, using any combination of 0~9, # and . Conditions none feature cross reference to...

  • Page 390

    Issue 4.0 2-350 program 21 : outgoing call setup description use program 21-15 : individual trunk group routing for extensions to designate the alternate trunk access route accessed when a user dials the alternate trunk route access code. Refer to program 11- 09 : trunk access code when setting up a...

  • Page 391

    Issue 4.0 sv9100 programming manual 2-351 description use program 21-16 : trunk group routing for networking to assign program 14-06 routes for a networked system. This is required to seize the trunk in a networked system (extension in system a tries to make an external call using a trunk in system ...

  • Page 392

    Issue 4.0 2-352 program 21 : outgoing call setup description use program 21-17 : ip trunk (sip) calling party number setup for trunk set the sip calling party number for individual trunks. Conditions none feature cross reference none program 21 : outgoing call setup 21-17 : ip trunk (sip) calling pa...

  • Page 393

    Issue 4.0 sv9100 programming manual 2-353 description use program 21-18 : ip trunk (h.323) calling party number setup for extension to assign the calling party number for each extension. The assigned number is sent to the exchange when the caller places an outgoing call. Conditions none feature cros...

  • Page 394

    Issue 4.0 2-354 program 21 : outgoing call setup description use program 21-19 : ip trunk (sip) calling party number setup for extension to set the sip calling party number for an individual extension. Conditions none feature cross reference none program 21 : outgoing call setup 21-19 : ip trunk (si...

  • Page 395

    Issue 4.0 sv9100 programming manual 2-355 description use program 21-21 : toll restriction for trunks (seized trunk basis setting) to define the toll restriction class to each trunk. The details of toll restriction are defined by prg 21-05 and 21-06. This program is compared to station restriction c...

  • Page 396

    Issue 4.0 2-356 program 21 : outgoing call setup description use program 21-22 : co message waiting indication – call back settings to define the settings of co message waiting indication. Conditions none feature cross reference none program 21 : outgoing call setup 21-22 : co message waiting indica...

  • Page 397

    Issue 4.0 sv9100 programming manual 2-357 description use program 21-25 : expansion calling party setup for extension to define cli number to an extension. This program is used only when prg14-01-38 is set to ‘2’. Conditions none feature cross reference none program 21 : outgoing call setup 21-25 : ...

  • Page 398

    Issue 4.0 2-358 program 21 : outgoing call setup.

  • Page 399

    Sv9100 programming manual 2-359 program: 22 description use program 22-01 : system options for incoming calls to define the system options for incoming calls. Program 22 : incoming call setup 22-01 : system options for incoming calls level: in input data item no. Item input data default description ...

  • Page 400

    Issue 4.0 2-360 program 22 : incoming call setup conditions none feature cross reference central office calls, answering 09 did to trunk to trunk no answer timer 0~64800 (sec) 20 10 vrs waiting message operation 0 = enable always 1 = change by manual operation 0 set up the operation mode for auto at...

  • Page 401

    Issue 4.0 sv9100 programming manual 2-361 description use program 22-02 : incoming call trunk setup to assign the incoming trunk type for each trunk. There is one item for each night service mode. Conditions when connecting to t1 trunks, after changing program 22-02-01 to match the telco connected t...

  • Page 402

    Issue 4.0 2-362 program 22 : incoming call setup feature cross reference central office calls, answering.

  • Page 403

    Issue 4.0 sv9100 programming manual 2-363 description use program 22-03 : trunk ring tone range to select the ring tone range for the trunk. The trunk uses a ring tone in the range selected when it rings an extension. Eight ring tones are available. Customize the trunk ring tones in program 82-01. P...

  • Page 404

    Issue 4.0 2-364 program 22 : incoming call setup conditions none feature cross reference selectable ring tones pattern 6 high middle low 1400hz 760hz 660hz 540hz 540hz 540hz 8hz 8hz 8hz pattern 7 high middle low 2000hz 2000hz 1100hz 1100hz 540hz 760hz 16hz 16hz 16hz pattern 8 high middle low 2000hz ...

  • Page 405

    Issue 4.0 sv9100 programming manual 2-365 description use program 22-04 : incoming extension ring group assignment to assign extensions to ring groups. Calls ring extensions according to ring group programming. Use program 22-05 to assign trunks to ring groups and use program 22-06 to set the ringin...

  • Page 406

    Issue 4.0 2-366 program 22 : incoming call setup description use program 22-05 : incoming trunk ring group assignment to assign trunks to incoming ring groups. Conditions none feature cross reference ring groups program 22 : incoming call setup 22-05 : incoming trunk ring group assignment level: in ...

  • Page 407

    Issue 4.0 sv9100 programming manual 2-367 description use program 22-06 : normal incoming ring mode to define whether or not an extension should ring for the normal incoming ring mode. Conditions none feature cross reference central office calls, answering program 22 : incoming call setup 22-06 : no...

  • Page 408: 22-07 : Dil Assignment

    Issue 4.0 2-368 program 22 : incoming call setup description use program 22-07 : dil assignment to assign the destination extension or department calling group for each dil incoming trunk. A dil rings an extension directly, without any other access map or ring group programming. If an extension has ...

  • Page 409

    Issue 4.0 sv9100 programming manual 2-369 description for dil delayed ringing, use program 22-08 : dil/irg no answer destination to assign the dil no answer ring group. An unanswered dil rings this group after the dil no answer time expires (program 22-01-04). Dil delayed ringing can also reroute ou...

  • Page 410: 22-09 : Did Basic Data Setup

    Issue 4.0 2-370 program 22 : incoming call setup description use program 22-09 : did basic data setup to define the basic setting of dial-in incoming calls for each trunk group. Program 22 : incoming call setup 22-09 : did basic data setup level: in input data trunk group number 001~100 item no. Ite...

  • Page 411

    Issue 4.0 sv9100 programming manual 2-371 conditions none feature cross reference direct inward dialing (did) 08 t302 time-out operation (only overlap receiving mode) 0 = disconnect (cut) 1 = transfer (refer to program 22-12 : did intercept ring group on page 2-378 .) 0 item no. Item input data defa...

  • Page 412

    Issue 4.0 2-372 program 22 : incoming call setup description use program 22-10 : did translation table setup to specify the size of the did translation tables. There are 2000 translation table entries that you can allocate among 20 translation tables. Default table program 22 : incoming call setup 2...

  • Page 413

    Issue 4.0 sv9100 programming manual 2-373 conditions none feature cross reference direct inward dialing (did).

  • Page 414

    Issue 4.0 2-374 program 22 : incoming call setup description use program 22-11 : did translation table number conversion to specify for each translation table entry (4000). The digits received by the system (eight maximum) the extension the system dials after translation (24 digits maximum) the name...

  • Page 415

    Issue 4.0 sv9100 programming manual 2-375 8 enter characters: t-v, t-v, 8. 9 enter characters: w-z, w-z, 9. 0 enter characters: 0 ! “ # $ % & ’ ( ) ô Õ ú ä ö ü enter characters: + , - . / : ; ? π Σ Ω ∞ ¢ £ # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pr...

  • Page 416

    Issue 4.0 2-376 program 22 : incoming call setup 04 transfer operation mode 0 = no transfer 1 = busy 2 = no answer 3 = busy/no answer 0 05 transfer destination number 1 0 = no setting 1~100 = incoming group 102 = in-skin/external voice mail or inmail 201~264 = extension group 400 = valid extension n...

  • Page 417

    Issue 4.0 sv9100 programming manual 2-377 conditions when the trunk type is set to 3 (did) in 22-02-01, the did transfer destination for each did feature is not supported. This feature is supported only for did trunks when assigned as vrs. Feature cross reference direct inward dialing (did).

  • Page 418

    Issue 4.0 2-378 program 22 : incoming call setup description for each did translation table, use program 22-12 : did intercept ring group to define the first destination group for did calls. Depending on the entry in program 22-09-02 and 22-11-04, the incoming calls route to the first destination gr...

  • Page 419

    Issue 4.0 sv9100 programming manual 2-379 conditions none feature cross reference direct inward dialing (did).

  • Page 420

    Issue 4.0 2-380 program 22 : incoming call setup description use program 22-13 : did trunk group to translation table assignment to assign the did trunk groups to did translation tables. Did trunks should be in their own group. If you have more than one type of did trunk, put each type in a separate...

  • Page 421

    Issue 4.0 sv9100 programming manual 2-381 description use program 22-14 : vrs delayed message for irg (incoming group ring)to define for each incoming ring group the timers, vrs message number and type of tone for vrs waiting message. Program 22 : incoming call setup 22-14 : vrs delayed message for ...

  • Page 422

    Issue 4.0 2-382 program 22 : incoming call setup conditions none feature cross reference none.

  • Page 423

    Issue 4.0 sv9100 programming manual 2-383 description use program 22-15 : vrs delayed message for department group to define for each department (extension) group the timers, vrs message number and tone kind for vrs delayed message. There are 64 available department groups. Program 22 : incoming cal...

  • Page 424

    Issue 4.0 2-384 program 22 : incoming call setup conditions none feature cross reference department group.

  • Page 425

    Issue 4.0 sv9100 programming manual 2-385 description use program 22-16: private call refuse target area setup to define speed dial group number for private call refuse. Conditions none feature cross reference department group program 22 : incoming call setup 22-16 : private call refuse target area ...

  • Page 426

    Issue 4.0 2-386 program 22 : incoming call setup description use program 22-17: dial-in conversion table area setup for time pattern to define time zone and dial-in conversion table (program 22-11) for time pattern. Conditions none feature cross reference none program 22 : incoming call setup 22-17 ...

  • Page 427

    Issue 4.0 sv9100 programming manual 2-387 description use program 22-18: private call assignment setup to define assignment and incoming ring pattern for private calls. Conditions none feature cross reference none program 22 : incoming call setup 22-18 : private call assignment setup level: in input...

  • Page 428

    Issue 4.0 2-388 program 22 : incoming call setup description use program 22-20: flexible ringing by caller id setup to set flexible ringing by caller id per timer pattern mode. Conditions none feature cross reference none program 22 : incoming call setup 22-20 : flexible ringing by caller id setup l...

  • Page 429: 23-02 : Call Pickup Groups

    Sv9100 programming manual 2-389 program: 23 description use program 23-02 : call pickup groups to assign extensions to call pickup groups. This program also lets you assign an extension call pickup group priority. If two extensions in a group are ringing at the same time, group call pickup intercept...

  • Page 430

    Issue 1.0 2-390 program 23 : answer features setup description use program 23-03 : universal answer/auto answer to assign trunk routes (set in program 14-06) to extensions for universal answer. If the call ringing the paging system is in an extension assigned route, the user can dial the universal a...

  • Page 431

    Issue 1.0 sv9100 programming manual 2-391 conditions none feature cross reference line preference night service.

  • Page 432

    Issue 1.0 2-392 program 23 : answer features setup description use program 23-04 : ringing line preference for virtual extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. Conditions none feature cross reference call arrival keys (car)/s...

  • Page 433

    Sv9100 programming manual 2-393 program: 24 description use program 24-01 : system options for hold to define the system options for the hold feature. Program 24 : hold/transfer setup 24-01 : system options for hold level: in input data item no. Item input data default related program 01 hold recall...

  • Page 434

    Issue 4.0 2-394 program 24 : hold/transfer setup conditions none feature cross reference hold park 07 park hold time – extended (recall) a call left parked longer than this time recalls the extension that initially parked it. 0~64800 (sec) 300 20-11-19 input data (continued) item no. Item input data...

  • Page 435

    Issue 4.0 sv9100 programming manual 2-395 description use program 24-02 : system options for transfer to define the system options for the transfer feature. Program 24 : hold/transfer setup 24-02 : system options for transfer level: in input data item no. Item input data default related program 01 b...

  • Page 436

    Issue 4.0 2-396 program 24 : hold/transfer setup conditions none feature cross reference transfer 07 trunk-to-trunk transfer release warning tone time starts when a trunk begins talking with another trunk (for example: trunk-to-trunk transfer, outgoing from trunk, tandem trunking). When this time ex...

  • Page 437: 24-03 : Park Group

    Issue 4.0 sv9100 programming manual 2-397 description use program 24-03 : park group to assign an extension to a park group. The system allows a total of 64 park groups. An extension user can pick up only a call parked in orbit by an extension user in their own group. Conditions none feature cross r...

  • Page 438

    Issue 4.0 2-398 program 24 : hold/transfer setup description use program 24-04 : automatic trunk-to-trunk transfer target setup to assign the speed dialing number bin which should be used as the destination of the automatic trunk-to-trunk transfer. Conditions none feature cross reference call forwar...

  • Page 439

    Issue 4.0 sv9100 programming manual 2-399 description use program 24-05 : department group transfer target setup to assign the speed dialing bin which is used as the destination of the extension for the extension group. Conditions none feature cross reference transfer program 24 : hold/transfer setu...

  • Page 440

    Issue 4.0 2-400 program 24 : hold/transfer setup description use program 24-09 : call forward split settings to assign call forwarding type and the destination number for each extension/virtual extension. The destination can have up to 24 digits, using 0~9, , #, and p (p is a pause used for analog t...

  • Page 441

    Issue 4.0 sv9100 programming manual 2-401 conditions none feature cross reference call forwarding, off-premise 06 call forwarding destination for ctx/pbx for all call, no answer: 0~9, #, , r, and p (up to 24 digits) none 07 call forwarding destination for ctx/pbx for busy: 0~9, #, , r, and p (up to ...

  • Page 442

    Issue 4.0 2-402 program 24 : hold/transfer setup.

  • Page 443: Program 25 : Vrs/disa Setup

    Sv9100 programming manual 2-403 program: 25 description use program 25-01 : vrs/disa line basic data setup to define the basic setting of each vrs/disa line. Conditions none feature cross reference direct inward system access (disa) program 25 : vrs/disa setup 25-01 : vrs/disa line basic data setup ...

  • Page 444: Program 25 : Vrs/disa Setup

    Issue 4.0 2-404 program 25 : vrs/disa setup description use program 25-02 : did/disa vrs message to assign the vrs message number to be used as the automated attendant message for each trunk which is assigned as a vrs/disa. Conditions none feature cross reference direct inward system access (disa) p...

  • Page 445: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-405 description use program 25-03 : vrs/disa transfer ring group with incorrect dialing to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial. The call can either disconnect (0) or transfer to an al...

  • Page 446: Program 25 : Vrs/disa Setup

    Issue 4.0 2-406 program 25 : vrs/disa setup description use program 25-04 : vrs/disa transfer ring group with no answer/busy to set the operating mode of each disa trunk. This sets what happens to the call when the disa or automated attendant caller calls a busy or unanswered extension. The call can...

  • Page 447: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-407 description use program 25-05 : vrs/disa error message assignment to assign the vrs message number to be used as the automated attendant error message. For each vrs/disa trunk that the vrs answers, enter the vrs message (1~100) the outside caller hears if th...

  • Page 448: Program 25 : Vrs/disa Setup

    Issue 4.0 2-408 program 25 : vrs/disa setup description use program 25-06 : vrs/disa one-digit code attendant setup to set up single digit dialing through the vrs. This gives vrs callers single key access to extensions, the company operator, department calling groups and voice mail. For each vrs mes...

  • Page 449

    Issue 4.0 sv9100 programming manual 2-409 conditions outside caller may not be able to dial individual extensions or lines, if the same first digit is defined here. Only one key dialing is supported for extension dialing. Feature cross reference direct inward system access (disa) voice response syst...

  • Page 450: Program 25 : Vrs/disa Setup

    Issue 4.0 2-410 program 25 : vrs/disa setup description use program 25-07 : system timers for vrs/disa to set the value for the system timers which affect did and disa. Refer to the following chart for a description of each option, its range and default setting. Program 25 : vrs/disa setup 25-07 : s...

  • Page 451

    Issue 4.0 sv9100 programming manual 2-411 conditions none feature cross reference direct inward system access (disa) 07 long conversation warning tone time determine the time a disa caller or any trunk-to-trunk (such as tandem trunking) conversation can talk before the long conversation tone is hear...

  • Page 452: Program 25 : Vrs/disa Setup

    Issue 4.0 2-412 program 25 : vrs/disa setup description use program 25-08 : disa user id setup to set the 6-digit disa password for each user. There are 15 users each with one 6-digit password. Conditions none feature cross reference direct inward system access (disa) program 25 : vrs/disa setup 25-...

  • Page 453: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-413 description use program 25-09 : class of service for disa users to set the disa class of service for each user. When a disa caller enters a password (defined in program 25-08), the system identifies the user and associates the appropriate disa class of servi...

  • Page 454: Program 25 : Vrs/disa Setup

    Issue 4.0 2-414 program 25 : vrs/disa setup description use program 25-10 : trunk group routing for disa to assign the trunk group route chosen when a user places a disa call to the system and dials 9. Set trunk group routing in program 14-06. Enable or disable the disa caller ability to dial 9 in p...

  • Page 455: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-415 description for systems that use toll restriction, use program 25-11 : disa toll restriction class to assign a toll restriction class (1~15) to each disa user (1~15). The system uses the toll restriction class you enter in program 21-05 and 21-06. The toll r...

  • Page 456: Program 25 : Vrs/disa Setup

    Issue 4.0 2-416 program 25 : vrs/disa setup description use program 25-12 : alternate trunk group routing for disa to define the trunk route selected when a disa caller dials the alternate trunk access code. The route selected is based on the disa caller class of service, which in turn is determined...

  • Page 457: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-417 description use program 25-13 : system option for disa to enter the password disa callers must dial before the system allows them to record, listen to and or erase the vrs messages. This program also is used to define additional disa call options. Conditions...

  • Page 458: Program 25 : Vrs/disa Setup

    Issue 4.0 2-418 program 25 : vrs/disa setup description use program 25-15 : vrs/disa transfer target setup to assign a speed dial number when a dial tone times-out, or when the wrong number is received and the target extension does not answer or is busy. Conditions related to program 25-03-01 and pr...

  • Page 459: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-419 description use program 25-16 : vrs/disa talkie base setup to assign vrs/disa timer values. Conditions none program 25 : vrs/disa setup 25-16 : vrs/disa talkie base setup level: in input data talkie number 1~100 item no. Item input data default 01 vrsdisa si...

  • Page 460

    Issue 4.0 2-420 program 25 : vrs/disa setup feature cross reference direct inward system access (disa) voice response system (vrs).

  • Page 461: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-421 description use program 25-17 : vrs/disa attendant message service setup to set what happens to a call when the disa or automated attendant caller dials incorrectly or waits too long to dial, and for no answer/busy. The call can either disconnect (0) or tran...

  • Page 462

    Issue 4.0 2-422 program 25 : vrs/disa setup conditions none feature cross reference direct inward system access (disa) voice response system (vrs) direct inward dial (did).

  • Page 463: Program 25 : Vrs/disa Setup

    Issue 4.0 sv9100 programming manual 2-423 description use program 25-18 : vrs/disa attendant message timer setup to set the value for the system timers which affect vrs and disa. Refer to the following chart for a description of each option, its range and default setting. Conditions none feature cro...

  • Page 464

    Issue 4.0 2-424 program 25 : vrs/disa setup.

  • Page 465: Program 26 : Ars Service

    Sv9100 programming manual 2-425 program: 26 description use program 26-01 : automatic route selection service to define the system options for automatic route selection (ars). Program 26 : ars service 26-01 : automatic route selection service level: in input data item no. Item input data default rel...

  • Page 466

    Issue 4.0 2-426 program 26 : ars service conditions none feature cross reference automatic route selection.

  • Page 467: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-427 description use program 26-02 : dial analysis table for ars/lcr to set pre-transaction tables for selecting automatic route selection (ars). Service type 1 (route to trunk group number) – the number routes to a trunk group. Service type 2 (f-route selected) ...

  • Page 468

    Issue 4.0 2-428 program 26 : ars service conditions none feature cross reference automatic route selection 06 lcr carrier table entry 0 ~ 25 0 07 network specified parameter table 0 ~ 16 0 26-12 item no. Item input data default related programming.

  • Page 469: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-429 description use program 26-03 : ars dial treatments to assign the 15 dial treatments for automatic ars dialing translation. Assign dial treatments to service numbers (trunk groups) in program 26-02. The ars dial treatment options are: 3 – delete the npa if d...

  • Page 470

    Issue 4.0 2-430 program 26 : ars service conditions none feature cross reference automatic route selection input data dial treatment table number 1~15 item no. Item input data default 01 treatment code 24 characters maximum no setting.

  • Page 471: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-431 description use program 26-04 : ar s class of service to set the ars class of service for an extension. Automatic route selection uses ars class of service when determining how to route extension calls. Conditions none feature cross reference automatic route...

  • Page 472: Program 26 : Ars Service

    Issue 4.0 2-432 program 26 : ars service description use program 26-05 : lcr carrier table to set the carrier table for lcr. Conditions none feature cross reference none program 26 : ars service 26-05 : lcr carrier table level: in input data carrier table number 1 ~ 25 item no. Name input data defau...

  • Page 473: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-433 description use program 26-06 : lcr authorization code table to set the authorization code table for lcr. Conditions none feature cross reference none program 26 : ars service 26-06 : lcr authorization code table level: in input data authorization table numb...

  • Page 474: Program 26 : Ars Service

    Issue 4.0 2-434 program 26 : ars service description use program 26-07 : lcr cost center code table to set the cost center code for lcr. Conditions none feature cross reference none program 26 : ars service 26-07 : lcr cost center code table level: in input data extension number up to eight digits i...

  • Page 475: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-435 description use program 26-08 : lcr manual override access code table to set the manual override access code for lcr. Conditions none feature cross reference none program 26 : ars service 26-08 : lcr manual override access code table level: in input data man...

  • Page 476: Program 26 : Ars Service

    Issue 4.0 2-436 program 26 : ars service description use program 26-09 : lcr manual override exemption table to set the manual override exemption for lcr. Conditions none feature cross reference none program 26 : ars service 26-09 : lcr manual override exemption table level: in input data manual ove...

  • Page 477: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-437 description use program 26-11 : transit network id table to define transit network id for alternate carrier access, which is referred from program 26-03. Conditions none feature cross reference none program 26 : ars service 26-11 : transit network id table l...

  • Page 478: Program 26 : Ars Service

    Issue 4.0 2-438 program 26 : ars service description use program 26-12 : network specific parameter table for ars to define the network specific parameter table. Conditions none feature cross reference none program 26 : ars service 26-12 : network specific parameter table for ars level: in input dat...

  • Page 479: Program 26 : Ars Service

    Issue 4.0 sv9100 programming manual 2-439 description use program 26-13 : ars class of service for netlink (dt700) sets an extension’s ars class of service when used for netlink. Automatic route selection uses ars class of service when determining how to route an extension’s calls. Conditions only w...

  • Page 480

    Issue 4.0 2-440 program 26 : ars service.

  • Page 481

    Sv9100 programming manual 2-441 program: 30 description use program 30-01 : dss console operating mode to set the mode of the system dss consoles. The entry for this option applies to all the system dss consoles. The available options are: regular (business) mode (0) hotel mode (1) monitor mode (2) ...

  • Page 482

    Issue 4.0 2-442 program 30 : dss/dls console setup description use program 30-02 : dss console extension assignment to identify which extensions have dss consoles connected. Up to 32 different extensions with dss consoles can be set up. A single extension can have up to four 60-button dss consoles (...

  • Page 483

    Issue 4.0 sv9100 programming manual 2-443 description use program 30-03 : dss console key assignment to customize the key assignments for 60-button dss consoles. A dss console key can have any function with up to four digits (e.G., extension number or service code). To prevent lamp problems when rea...

  • Page 484

    Issue 4.0 2-444 program 30 : dss/dls console setup function number list [1] general functional level (00~99) function number function additional data led indication 00 not defined 01 dss/one-touch extension number or any numbers (up to 24 digits) red on: extension busy off: extension idle rapid blin...

  • Page 485

    Issue 4.0 sv9100 programming manual 2-445 22 internal all call paging none 23 meet-me answer to internal paging none 24 call pickup none 25 call pickup for another group none 26 call pickup for specified group call pickup group number none 27 speed dial – system/private speed dial number (speed/priv...

  • Page 486

    Issue 4.0 2-446 program 30 : dss/dls console setup 41 secretary buzzer extension number red on: transmission side rapid blink (red): receiver side 42 boss – secretary call pickup extension number red on: boss – secretary mode 43 series call none 44 common hold none 45 exclusive hold none 46 departme...

  • Page 487

    Issue 4.0 sv9100 programming manual 2-447 63 outgoing call without caller id (isdn) red on: active 64 --- not used --- 65 --- not used --- 66 --- not used --- 67 --- not used --- 68 --- not used --- 69 --- not used --- 70 --- not used --- 71 --- not used --- 72 keypad facility key 73 keypad hold key...

  • Page 488

    Issue 4.0 2-448 program 30 : dss/dls console setup 92 wake up call indication green on: wake up call indication mode on off: wake up call indication mode off 93 room status indication green on: active room status off: room status indication mode off 94 call attendant 95 page switching red on: dss pa...

  • Page 489

    Issue 4.0 sv9100 programming manual 2-449 default the dss keys 01~60 of all dss consoles = dss/one-touch key 101~160 the dss keys 61~114 of all dss consoles = none conditions none feature cross reference direct station selection (dss) console function number list [2] appearance function level ( 00 -...

  • Page 490

    Issue 4.0 2-450 program 30 : dss/dls console setup description use program 30-04 : dss console alternate answer to assign the alternate dss console station in case off-duty mode is set (by pressing the alt key on the dss console). Conditions related extension is assigned in prg30-02. Alternate answe...

  • Page 491

    Issue 4.0 sv9100 programming manual 2-451 description use program 30-05 : dss console lamp table to define the led patterns for functions on the dss consoles. Program 30 : dss/dls console setup 30-05 : dss console lamp table level: in input data item no. Item lamp pattern data default 02 busy extens...

  • Page 492

    Issue 4.0 2-452 program 30 : dss/dls console setup 21 vm message indication 0~7 3 (rw) table 2-10 ed patterns for dss console input data (continued) item no. Item lamp pattern data default.

  • Page 493

    Issue 4.0 sv9100 programming manual 2-453 conditions none feature cross reference direct station selection (dss) console.

  • Page 494

    Issue 4.0 2-454 program 30 : dss/dls console setup description use program 30-10 : dss console ip terminal setup to set the mac address for a particular ip dss console. This must be done before the console can be associated to the attendant phone. The system supports up to 32 ip dss consoles. Condit...

  • Page 495: Program 31 : Paging Setup

    Sv9100 programming manual 2-455 program: 31 description use program 31-01 : system options for internal/external paging to define the system options for internal/external paging. The system shows the name you program on the telephone display. Use the following chart when entering and editing text. W...

  • Page 496

    Issue 4.0 2-456 program 31 : paging setup conditions none feature cross reference paging, external paging, internal # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pressing # again = space. (in system programming mode, use the right arrow soft key instead ...

  • Page 497: Program 31 : Paging Setup

    Issue 4.0 sv9100 programming manual 2-457 description use program 31-02 : internal paging group assignment to assign extensions to internal paging groups (i.E., page zones). The setting in this program also determines if the internal page group can receive internal all call paging. The system can ha...

  • Page 498: Program 31 : Paging Setup

    Issue 4.0 2-458 program 31 : paging setup description use program 31-03 : internal paging group settings to assign names to internal paging groups (i.E., page zones) and to define the splash tone for internal paging. The system shows the names you program on the telephone display. Use the following ...

  • Page 499

    Issue 4.0 sv9100 programming manual 2-459 default item 01 : internal paging group name # # = accepts an entry (only required if two letters on the same key are needed - ex: tom). Pressing # again = space. (in system programming mode, use the right arrow soft key instead to accept and/or add a space....

  • Page 500

    Issue 4.0 2-460 program 31 : paging setup conditions none feature cross reference paging, internal.

  • Page 501: Program 31 : Paging Setup

    Issue 4.0 sv9100 programming manual 2-461 description use program 31-04 : external paging zone group to assign each external paging zone to an external paging group. Users call the external paging group when broadcasting announcements to the external zone. When programming, the zones on the pgd(2)-u...

  • Page 502: Program 31 : Paging Setup

    Issue 4.0 2-462 program 31 : paging setup description use program 31-05 : universal night answer/ring over page to assign universal night answer ringing to each external paging zone. For each trunk port, make a separate entry for each external paging zone. When programming, the zones on the pgd(2)-u...

  • Page 503: Program 31 : Paging Setup

    Issue 4.0 sv9100 programming manual 2-463 description use program 31-06 : external speaker control to define the settings for the external speaker using an amplifier. Program 31 : paging setup 31-06 : external speaker control level: in input data external speaker number 1~9 item no. Item input data ...

  • Page 504

    Issue 4.0 2-464 program 31 : paging setup conditions none feature cross reference paging, external.

  • Page 505: Program 31 : Paging Setup

    Issue 4.0 sv9100 programming manual 2-465 description use program 31-07 : combined paging assignments to assign an external paging group (0~8) to an internal paging zone (0~64) for combined paging. When an extension user makes a combined page, they simultaneously broadcast into both the external and...

  • Page 506: Program 31 : Paging Setup

    Issue 4.0 2-466 program 31 : paging setup description use program 31-08 : bgm on external paging to set the background music option for each external paging zone. If enabled, the system plays background music over the zone when it is idle. When programming, the zones on the pgd(2)-u10 adp are number...

  • Page 507

    Sv9100 programming manual 2-467 program: 32 description use program 32-01 : door box timers setup to assign the timers used for the door box. Conditions none feature cross reference door box program 32 : door box and sensor setup 32-01 : door box timers setup level: in note the door box feature is c...

  • Page 508

    Issue 1.0 2-468 program 32 : door box and sensor setup description use program 32-02 : door box ring assignment to assign the extension which rings when a caller presses the associated door box call button. Conditions none feature cross reference door box program 32 : door box and sensor setup 32-02...

  • Page 509: 32-03 : Door Box Basic Setup

    Issue 1.0 sv9100 programming manual 2-469 description use program 32-03 : door box basic setup to select the chime pattern and gain level for each door box. There are six distinctive chime patterns. The chime tones are defined in 80-01 : service tone setup on page 2-673 . Conditions none feature cro...

  • Page 510: 32-04 : Door Box Name Setup

    Issue 1.0 2-470 program 32 : door box and sensor setup description use program 32-04 : door box name setup to define the name of each door box. Conditions none feature cross reference door box program 32 : door box and sensor setup 32-04 : door box name setup level: in note the door box feature is c...

  • Page 511: 33-01 : Aci Port Type Setup

    Sv9100 programming manual 2-471 program: 33 description use program 33-01 : aci port type setup to set the function of each software port on an analog communications interface. Each aci software port can have only one function (input, output or none). Conditions none feature cross reference analog c...

  • Page 512

    Issue 4.0 2-472 program 33 : cta and aci setup description use program 33-02 : aci department calling group to assign aci ports to department groups. An aci port can be in only one group. Also use this program to set the aci port priority. When a call comes into the aci department group, it connects...

  • Page 513: Program 34 : Tie Line Setup

    Sv9100 programming manual 2-473 program: 34 description use program 34-01 : e&m tie line basic setup to define the basic settings for each e&m tie line. Program 34 : tie line setup 34-01 : e&m tie line basic setup level: in input data trunk port number 001~400 item no. Item input data default descri...

  • Page 514

    Issue 4.0 2-474 program 34 : tie line setup conditions none feature cross reference tie lines.

  • Page 515: Program 34 : Tie Line Setup

    Issue 4.0 sv9100 programming manual 2-475 description use program 34-02 : e&m tie line class of service to assign a class of service to a tie line (there are 15 tie line classes of service). The class of service options are defined in program 20-14. For each tie line, make a separate entry for each ...

  • Page 516: Program 34 : Tie Line Setup

    Issue 4.0 2-476 program 34 : tie line setup description use program 34-03 : trunk group routing for e&m tie lines to assign the trunk group route 1~8 or 1~100) chosen when a user seizes a tie line and dials 9. (set trunk group routing in program 14-07.) if the system has automatic route selection, d...

  • Page 517: Program 34 : Tie Line Setup

    Issue 4.0 sv9100 programming manual 2-477 description use program 34-04 : e&m tie line toll restriction class to enter a toll restriction class for each tie line. There are 15 toll restriction classes which are defined in programs 21-05 and 21-06. For each tie line, you make a separate toll restrict...

  • Page 518: Program 34 : Tie Line Setup

    Issue 4.0 2-478 program 34 : tie line setup description use program 34-05 : tie line outgoing call restriction to build a restriction matrix for outgoing trunk calls placed from an inbound trunk (e.G., dialed from a tie line). For each inbound trunk group, enable or disable access to each co trunk g...

  • Page 519: Program 34 : Tie Line Setup

    Issue 4.0 sv9100 programming manual 2-479 description use program 34-06 : add/delete digit for e&m tie line to set digits that the system should add or delete for tie lines. Delete digit some tie line networks pass the location number and extension number to the remote side. This program allows the ...

  • Page 520: Program 34 : Tie Line Setup

    Issue 4.0 2-480 program 34 : tie line setup description use program 34-07 : e&m tie line timer to define the system service tone timers. Conditions if prg 34-07-05 is left at default (30) the transferred call recalls to the station that performed the transfer when not answered. Feature cross referen...

  • Page 521: Program 34 : Tie Line Setup

    Issue 4.0 sv9100 programming manual 2-481 description use program 34-08 : toll restriction data for e&m tie lines to define the toll restriction data for e&m tie lines. This data should be defined if tie line toll restriction is enabled in program 21-05-13. Conditions none feature cross reference ti...

  • Page 522: Program 34 : Tie Line Setup

    Issue 4.0 2-482 program 34 : tie line setup description use program 34-09 : ani/dnis service options to define the ani//dnis service option setup for e&m class of service. Program 34 : tie line setup 34-09 : ani/dnis service options level: in input data class of service 01~15 item no. Name input dat...

  • Page 523

    Issue 4.0 sv9100 programming manual 2-483 04 route table setup of target dial set how the system uses the route data (gathered in item 3) to route incoming ani/dnis calls. If option 2 is selected, and the call is to be routed using the did table (1), up to 8 digits can be matched. The number of expe...

  • Page 524

    Issue 4.0 2-484 program 34 : tie line setup conditions none feature cross reference t1 trunking (with ani/dnis compatibility) tie lines 08 routing when destination busy or no answer determine how the system handles an ani/dnis call if destination is busy or does not answer. 0 = play busy or ringback...

  • Page 525: Program 34 : Tie Line Setup

    Issue 4.0 sv9100 programming manual 2-485 description use program 34-10 : digits delete for t1 ani assignment to delete the information digits received from the network on feature group d trunks. Example: conditions none feature cross reference t1 trunking (with ani/dnis ability) program 34 : tie li...

  • Page 526

    Issue 4.0 2-486 program 34 : tie line setup.

  • Page 527: 35-01 : Smdr Options

    Sv9100 programming manual 2-487 program: 35 description use program 35-01 : smdr options to set the smdr (station message detail recording) options. Refer to the following chart for a description of each option, its range and default setting. Program 35 : smdr account code setup 35-01 : smdr options...

  • Page 528

    Issue 4.0 2-488 program 35 : smdr account code setup conditions none feature cross reference station message detail recording 08 format selection 0 = na type (north america) 1 = g/j type (overseas/ japan) 0 item no. Item input data default.

  • Page 529: 35-02 : Smdr Output Options

    Issue 4.0 sv9100 programming manual 2-489 description use program 35-02 : smdr output options to set the smdr (station message detail recording) output options. Refer to the following chart for a description of each option, its range and default setting. Program 35 : smdr account code setup 35-02 : ...

  • Page 530

    Issue 4.0 2-490 program 35 : smdr account code setup 09 extension number or name set to 1 to have the smdr report include extension numbers. Set to 0 to have the smdr report include extension names. 0 = name 1 = number 1 10 all lines busy (alb) output determine if the all lines busy (alb) indication...

  • Page 531

    Issue 4.0 sv9100 programming manual 2-491 conditions none feature cross reference station message detail recording 24 mark virtual loop define whether calls routed via the isdn virtual loopback are tagged. 0 = don’t mark 1 = mark 0 item no. Item input data default.

  • Page 532: 35-05 : Account Code Setup

    Issue 4.0 2-492 program 35 : smdr account code setup description use program 35-05 : account code setup to set various account code options for an extension class of service. Assign a class of service to extensions in program 20-06. Program 35 : smdr account code setup 35-05 : account code setup lev...

  • Page 533

    Issue 4.0 sv9100 programming manual 2-493 conditions none feature cross reference account codes.

  • Page 534

    Issue 4.0 2-494 program 35 : smdr account code setup description use program 35-06 : verified account code table to enter account codes into the verified account code list. You can enter up to 2000 codes using the characters 0~9 or # . Use the lk1 to enter a wild card. For example, the entry @234 me...

  • Page 535

    Sv9100 programming manual 2-495 program: 40 description use program 40-07 : voice prompt language assignment for vrs to specify the language to be used for the vrs prompts. Program 40 : voice recording system 40-07 : voice prompt language assignment for vrs level: in input data item no. Item input d...

  • Page 536

    Issue 4.0 2-496 program 40 : voice recording system conditions none feature cross reference voice mail integration (analog).

  • Page 537

    Issue 4.0 sv9100 programming manual 2-497 description in program 40-10 : voice announcement service option define the system options for the voice announcement feature. Program 40 : voice recording system 40-10 : voice announcement service option level: in input data item no. Item input data default...

  • Page 538

    Issue 4.0 2-498 program 40 : voice recording system conditions none feature cross reference voice response system (vrs) 07 set vrs message for caller id refuse (vrs msg cid) assign the vrs message number to be used as caller id refuse. When fixed message is set, vrs message guidance is: “your call c...

  • Page 539

    Issue 4.0 sv9100 programming manual 2-499 description in program 40-11 : preamble message assignment to assign the vrs message number to be used as the preamble message for each trunk. When the extension user answers the incoming call, the assigned vrs message is sent to the outside caller. Conditio...

  • Page 540

    Issue 4.0 2-500 program 40 : voice recording system.

  • Page 541: Program 41 : Acd Setup

    Sv9100 programming manual 2-501 program: 41 description in program 41-01 : system options for contact center todefine the system options for the contact center feature. Conditions none feature cross reference contact center program 41 : acd setup 41-01 : system options for contact center level: in i...

  • Page 542

    Issue 1.0 2-502 program 41 : acd setup.

  • Page 543: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-503 description in program 41-02 : group and agent assignments, for each extension number, assign an group (1~64). A group number is assigned to each work period number (1~8). The assigned extension works as an agent extension in the following cases: the trunk b...

  • Page 544: Program 41 : Acd Setup

    Issue 1.0 2-504 program 41 : acd setup description in program 41-03 : incoming ring group assignment for group, for each incoming trunk group set up in program 22-05, designate which group (1~64) the trunks should ring for each of the eight work periods. Also use this program to assign an incoming t...

  • Page 545

    Issue 1.0 sv9100 programming manual 2-505 conditions none feature cross reference contact center ring groups.

  • Page 546: Program 41 : Acd Setup

    Issue 1.0 2-506 program 41 : acd setup description for each group (1~64), use program 41-04 : group supervisor to assign the group supervisor extension and operating mode. Operating modes are: 0 = supervisor extension does not receive group calls. 1 = supervisor extension receives group overflow cal...

  • Page 547: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-507 description use program 41-05: agent work schedules to set up the work schedules for agents and groups. For each work schedule (1~4), designate the start and stop times for each of the eight work periods. After you set up the schedules in this program, assig...

  • Page 548: Program 41 : Acd Setup

    Issue 1.0 2-508 program 41 : acd setup description use program 41-06 : trunk work schedules to set up the work schedules for trunks. For each work schedule (1~4), designate the start and stop times for each of the eight work periods. After you set up the schedules, assign them to days of the week in...

  • Page 549: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-509 description use program 41-07 : weekly schedule setup to assign the four work schedules (1~4) to days of the week. The assignments you make in this program apply to both the agent work schedules (program 41- 05) and the trunk work schedules (program 41-06). ...

  • Page 550: Program 41 : Acd Setup

    Issue 1.0 2-510 program 41 : acd setup description for each group (1~64), use program 41-08 : overflow options to assign the overflow mode (0~9), destination and announcement message types. Delay announcement functions are not available for pilot number calls. Each group can have unique overflow opt...

  • Page 551

    Issue 1.0 sv9100 programming manual 2-511 conditions none feature cross reference contact center 06 incoming ring group when overflow 1~100 (used when 41-08-02 is set to 68) 1 item no. Item input data default.

  • Page 552: Program 41 : Acd Setup

    Issue 1.0 2-512 program 41 : acd setup description use program 41-09 : overflow table setting to define the group to which a call is transferred when overflow occurs. Conditions none feature cross reference contact center program 41 : acd setup 41-09 : overflow table setting level: sa input data gro...

  • Page 553: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-513 description use program 41-10 : aci delay announcement to define the aci port number to be used for the delay announcement. This program is activated when the delay announcement source and options are assigned as aci in program 41-08-03. Conditions none feat...

  • Page 554: Program 41 : Acd Setup

    Issue 1.0 2-514 program 41 : acd setup description use program 41-11 : vrs delay announcement to assign the vrs message number to use as the message source for the 1st and 2nd delay announcement messages. Refer to program 41-08 for more on setting up the overflow options. This program is activated w...

  • Page 555

    Issue 1.0 sv9100 programming manual 2-515 conditions none feature cross reference contact center 08 queue depth announcement input when the queue depth announcement is played. 0 = disable 1 = after 1st (1st) 2 = after 2nd (2nd) 3 = after 1st and 2nd (1st and 2nd) 0 item no. Item input data default.

  • Page 556: Program 41 : Acd Setup

    Issue 1.0 2-516 program 41 : acd setup description use program 41-12 : night announcement setup to define the night announce voice resource and sending time for each group. Night announcement availability depends on the setting in program 41-03- 02. The night announcement function is not available f...

  • Page 557: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-517 description use program 41-13 : vrs message number for night announcement to define the vrs message number to use as the night announcement. This program is activated when the night announcement source is assigned as vrs in program 41-12-01. Conditions none ...

  • Page 558: Program 41 : Acd Setup

    Issue 1.0 2-518 program 41 : acd setup description use program 41-14 : options setup to set various options for groups. When you set an option for an group, the setting is in force (if applicable) for all agents in the group. The chart below shows each of the options, the entries available, and the ...

  • Page 559

    Issue 1.0 sv9100 programming manual 2-519 07 automatic off duty for slt enable/disable automatic off duty (rest) mode for agents with slt. 0 = no change to off duty mode 1 = change to off duty mode automatically (skip) 0 08 off duty mode enable/disable the ability to receive internal calls when in o...

  • Page 560

    Issue 1.0 2-520 program 41 : acd setup conditions none feature cross reference contact center.

  • Page 561: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-521 description use program 41-15 : queue alarm information to assign the options for audible indication for log out/off duty mode for each group. These program settings provide an alarm to the agents, but no queue status display is indicated. Do not use these p...

  • Page 562

    Issue 1.0 2-522 program 41 : acd setup conditions none feature cross reference contact center.

  • Page 563: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-523 description use program 41-16 : threshold overflow to define the value of the threshold call overflow and the mode for each group. Conditions none feature cross reference contact center program 41 : acd setup 41-16 : threshold overflow level: sa input data g...

  • Page 564: Program 41 : Acd Setup

    Issue 1.0 2-524 program 41 : acd setup description use program 41-17 : login mode setup to define the login mode for each extension. If the aic login mode is enabled, set the aic login and aic logout service codes for the aic members in program 11- 13-08 and 11-13-09. Conditions if set to 1, note th...

  • Page 565: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-525 description use program 41-18 : agent identity code setup to define the agent identity code table. Program 41 : acd setup 41-18 : agent identity code setup level: sa input data aic table no. 001~960 item no. Item input data default 01 agent identity code up ...

  • Page 566

    Issue 1.0 2-526 program 41 : acd setup conditions none feature cross reference none.

  • Page 567: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-527 description use program 41-19 : voice mail delay announcement to assign vm8000 inmail master mailboxes (prg 47-03) as delay announcement mailboxes. Program 41 : acd setup 41-19 : voice mail delay announcement level: sa input data group number 1 ~ 64 item no....

  • Page 568

    Issue 1.0 2-528 program 41 : acd setup conditions none feature cross reference none 08 delay message interval time set the time for the interval between the delay messages. 0 ~ 64800 (sec) 20 item no. Item input data default.

  • Page 569: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-529 description use program 41-20 : queue display settings to assign the options for the queue status display feature. This program allows the queue status display, and causes an alarm to sound, when the parameters in this program are met. Program 41-15 can also...

  • Page 570

    Issue 1.0 2-530 program 41 : acd setup conditions none feature cross reference contact center input data group no. 01~64 item no. Item input data default 01 number of calls in queue set the number of calls that can accumulate in the queue before the queue status display (and optional queue alarm) oc...

  • Page 571: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-531 description use program 41-21 : login id setup to assign the login id code to skill table used for skill based routing. Conditions none feature cross reference contact center program 41 : acd setup 41-21 : login id setup level: sa input data login id 01~960 ...

  • Page 572: Program 41 : Acd Setup

    Issue 1.0 2-532 program 41 : acd setup description use program 41-22 : skill based routing setup to assign if the group can use or not use skill based routing. Conditions none feature cross reference contact center program 41 : acd setup 41-22 : skill based routing setup level: sa input data group n...

  • Page 573: Program 41 : Acd Setup

    Issue 1.0 sv9100 programming manual 2-533 description use program 41-23 : skill table setup to assign the skill level per table for each group. Conditions none feature cross reference contact center program 41 : acd setup 41-23 : skill table setup level: sa input data skill table 1~960 input data gr...

  • Page 574: Program 41 : Acd Setup

    Issue 1.0 2-534 program 41 : acd setup description use program 41-24 : caller id marking setup to assign enable/disable the availability of setting that the agent can mark the originator caller id, system base. Conditions none feature cross reference contact center program 41 : acd setup 41-24 : cal...

  • Page 575: Program 42 : Hotel Setup

    Sv9100 programming manual 2-535 program: 42 description use program 42-01 : system options for hotel/motel to assign the system options for hotel/motel service. Program 42 : hotel setup 42-01 : system options for hotel/motel level: in input data item no. Item input data default 01 answering message ...

  • Page 576

    Issue 4.0 2-536 program 42 : hotel setup refer to the tables below for valid status code changes when program 42-01-06 is enabled or disabled. Valid room status changes when program 42-01-06 is set to 1 (enabled) change status code 1 code 2 code 3 code 4 code 5 code 6 code 7 code 8 code 9 code 0 cod...

  • Page 577

    Issue 4.0 sv9100 programming manual 2-537 conditions none feature cross reference hotel/motel.

  • Page 578: Program 42 : Hotel Setup

    Issue 4.0 2-538 program 42 : hotel setup description use program 42-02 : hotel/motel telephone setup to define the basic operation of the hotel/motel extensions. Program 42 : hotel setup 42-02 : hotel/motel telephone setup level: in input data extension number 001 ~ 960 item no. Item input data defa...

  • Page 579

    Issue 4.0 sv9100 programming manual 2-539 conditions none feature cross reference hotel/motel.

  • Page 580: Program 42 : Hotel Setup

    Issue 4.0 2-540 program 42 : hotel setup description use program 42-03 : class of service options (hotel/motel) to set the hotel/motel class of service (cos) options. Assign class of service to extensions in program 42-02 : hotel/motel telephone setup. There are 15 classes of service. Refer to the f...

  • Page 581

    Issue 4.0 sv9100 programming manual 2-541 conditions none feature cross reference class of service hotel/motel 10 wake up call setting for own extension 0 = off 1 = on 0 0 11 change room status for own extension 0 = off 1 = on 0 0 12 slt room monitor enable (1)/disable (0) a single line telephone ab...

  • Page 582: Program 42 : Hotel Setup

    Issue 4.0 2-542 program 42 : hotel setup description use program 42-04 : hotel mode one-digit service codes to set up the hotel mode one-digit service codes which are assigned in 42-02-01. For each department calling group (1~64), you enter the destination for each single digit code (1~9, 0, , # ). ...

  • Page 583: Program 42 : Hotel Setup

    Issue 4.0 sv9100 programming manual 2-543 description use program 42-05 : hotel room status printer to set the cta port to output the hotel data (check- out sheet, room status, etc.) and the output options for the hotel/motel feature. Conditions room status reports output via a cta or ctu adapter re...

  • Page 584: Program 42 : Hotel Setup

    Issue 4.0 2-544 program 42 : hotel setup description use program 42-06 : pms service setting to set the pms integration settings when using pms-u10 and pms feature. Program 42 : hotel setup 42-06 : pms service setting level: in input data item no. Item input data default 01 pms port number a system ...

  • Page 585

    Issue 4.0 sv9100 programming manual 2-545 conditions none feature cross reference hotel/motel.

  • Page 586: Program 42 : Hotel Setup

    Issue 4.0 2-546 program 42 : hotel setup description use program 42-07 : pms restriction level conversion table to change the default toll restriction class on check in for a room (prg 42-02-02). Conditions none feature cross reference hotel/motel program 42 : hotel setup 42-07 : pms restriction lev...

  • Page 587: Program 42 : Hotel Setup

    Issue 4.0 sv9100 programming manual 2-547 description use program 42-07 : flexible setup for room status to enable dial room status codes. Note the code definitions only apply to the system itself. When sending room status messages to the pms application, the status codes are always sent as defined ...

  • Page 588

    Issue 4.0 2-548 program 42 : hotel setup.

  • Page 589

    Sv9100 programming manual 2-549 program: 44 description use program 44-01 : system options for ars/f-route to define the system options for the ars/f-route feature. Conditions none feature cross reference automatic route selection (ars) uniform numbering network program 44 : ars/f-route setup 44-01 ...

  • Page 590

    Issue 4.0 2-550 program 44 : ars/f-route setup description use program 44-02 : dial analysis table for ars/f-route access to set the pre-transaction table for selecting ars/f-route. Program 44 : ars/f-route setup 44-02 : dial analysis table for ars/f-route access level: in input data dial analysis t...

  • Page 591

    Issue 4.0 sv9100 programming manual 2-551 conditions none feature cross reference automatic route selection (ars) 03 additional data for the service type selected in 44-02-02, enter the additional data required. 1: delete digit = 0~255 (255 = delete all digits) 2: [program 44-01 : 0] ars/f-route tab...

  • Page 592

    Issue 4.0 2-552 program 44 : ars/f-route setup description when program 44-02-02 is set to type 3, use program 44-03 : dial analysis extension table to set the dial extension analysis table. These tables are used when the analyzed digits must be more than eight digits. If the received digits do not ...

  • Page 593

    Issue 4.0 sv9100 programming manual 2-553 conditions none feature cross reference automatic route selection (ars) dial analysis table number : 251 item no. Item input data default 03 ars/f-route select table number 0~500 (ars/f-route table number) with program 44-01 set to 0, program 44-05 is checke...

  • Page 594

    Issue 4.0 2-554 program 44 : ars/f-route setup description use program 44-04 : ars/f-route selection for time schedule to assign each ars/f-route selection number to an ars/f-route table number for each ars/f-route time mode. There are eight time modes for ars/f-route access. Conditions none feature...

  • Page 595: 44-05 : Ars/f-Route Table

    Issue 4.0 sv9100 programming manual 2-555 description use program 44-05 : ars/f-route table to set the ars/f-route table. There are four kinds of order. If the higher priority trunk groups are busy, the next order group is used. If a lower priority route is selected, the caller may be notified with ...

  • Page 596

    Issue 4.0 2-556 program 44 : ars/f-route setup conditions none feature cross reference automatic route selection (ars) 07 ars class of service select the ars class of service to use for the table. An extension ars cos is determined in program 26-04-01. 0~50 0 08 dial treatment select the dial treatm...

  • Page 597

    Issue 4.0 sv9100 programming manual 2-557 description use program 44-06 : additional dial table to set the additional dial table to add prior to the dialed ars/f- route number. The additional dial table used is determined in program 44-05-03. Conditions none feature cross reference automatic route s...

  • Page 598

    Issue 4.0 2-558 program 44 : ars/f-route setup description use program 44-07 : gain table for ars/f-route access to set the gain/pad table. If an extension dials ars/f-route number: the extension dial gain table, assigned in program 44-05, is activated. The extension dial gain table follows outgoing...

  • Page 599

    Issue 4.0 sv9100 programming manual 2-559 conditions none feature cross reference automatic route selection (ars).

  • Page 600

    Issue 4.0 2-560 program 44 : ars/f-route setup description use program 44-08 : time schedule for ars/f-route to define the daily pattern of the ars/f-route feature. Ars/f-route has 10 time patterns. These patterns are used in program 44-09 and 44-10. The daily pattern consists of 20 time settings. D...

  • Page 601

    Issue 4.0 sv9100 programming manual 2-561 conditions none feature cross reference automatic route selection (ars).

  • Page 602

    Issue 4.0 2-562 program 44 : ars/f-route setup description use program 44-09 : weekly schedule for ars/f-route to define a weekly schedule for using ars/f- route. The pattern number is defined in program 44-08-01. Conditions none feature cross reference automatic route selection (ars) program 44 : a...

  • Page 603

    Issue 4.0 sv9100 programming manual 2-563 description use program 44-10 : holiday schedule for ars/f-route to define a yearly schedule for ars/f-route. This schedule is used for setting special days such as national holidays. The pattern number is defined in program 44-08-01. Conditions none feature...

  • Page 604

    Issue 4.0 2-564 program 44 : ars/f-route setup.

  • Page 605

    Sv9100 programming manual 2-565 program: 45 description use program 45-01 : voice mail integration options to customize certain voice mail integration options. Program 45 : voice mail integration 45-01 : voice mail integration options level: in input data item no. Item input data default 01 voice ma...

  • Page 606

    Issue 4.0 2-566 program 45 : voice mail integration 08 centralized voice mail department group number assign which extension (department) group number is used as the centralized voice mail group. 0~64 0 09 centralized voice mail master name assign the centralized voice mail master name. Up to 12 cha...

  • Page 607

    Issue 4.0 sv9100 programming manual 2-567 conditions none feature cross reference voice mail integration (analog).

  • Page 608: 45-02 : Nsl Option Setup

    Issue 4.0 2-568 program 45 : voice mail integration description use program 45-02 : nsl option setup to setup the nsl options for voice mail integration. Conditions none feature cross reference none program 45 : voice mail integration 45-02 : nsl option setup level: in input data item no. Item input...

  • Page 609

    Issue 4.0 sv9100 programming manual 2-569 description use program 45-04 : voice mail digit add assignment to define the digits to add. Conditions none feature cross reference none program 45 : voice mail integration 45-04 : voice mail digit add assignment level: in input data item no. Item input dat...

  • Page 610: Signal

    Issue 4.0 2-570 program 45 : voice mail integration description use program 45-05 : voice mail send protocol signal without additional digits to send trunk number and/or station number information if integrating to voice mail when prg 45-04-xx is left blank and 45-01-15 is set to program. Conditions...

  • Page 611: Program 47 : Inmail

    Sv9100 programming manual 2-571 program: 47 description use program 47-01 : sv8100 inmail system options to set up the sv8100 inmail system-wide options. Program 47 : inmail 47-01 : sv8100 inmail system options level: in input data item no. Item input data default 02 sv8100 inmail master name (maste...

  • Page 612

    Issue 4.0 2-572 program 47 : inmail 03 subscriber message length (subs msg length) set the maximum length of recorded messages for: subscriber mailbox users dialing rs to record and send a message. Extension users leaving a message in a subscriber mailbox. Outside automated attendant callers accessi...

  • Page 613

    Issue 4.0 sv9100 programming manual 2-573 07 digital pager callback number (pager cback) set the digital pager callback number portion of the message notification callout number for a digital pager. This is the portion of the callout number that is appended to the pager service telephone number. Nor...

  • Page 614

    Issue 4.0 2-574 program 47 : inmail 09 wait between digital pager callout attempts (notify pager intvl) set the minimum time between unacknowledged or unanswered digital pager message notification callouts. (a subscriber acknowledges a digital pager notification by logging onto their mailbox.) after...

  • Page 615

    Issue 4.0 sv9100 programming manual 2-575 12 wait between rna non-pager callout attempts (notify rna intvl) set the time sv8100 inmail waits, after it dials an unanswered non-pager callout destination, before retrying the callout number. There are 3 types of unanswered non-pager callouts: if the cal...

  • Page 616

    Issue 4.0 2-576 program 47 : inmail conditions when changing 47-01-02, a system reset is required for the new setting to take affect. Feature cross reference none 15 send pager callout until acknowledged (retry until ack) when this option is set to 1, sv8100 inmail continues to retry a digital pager...

  • Page 617: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-577 description use 47-02 : sv8100 inmail station mailbox options to set up a station/extension mailbox. Station mailboxes are automatically assigned as subscriber mailboxes. Normally, sv8100 inmail station mailbox numbers 1~26 should correspond to extensions 10...

  • Page 618

    Issue 4.0 2-578 program 47 : inmail 04 message playback order set the subscriber mailbox message playback order. When a subscriber listens to their messages, sv8100 inmail can play the oldest messages first, or the newest messages first. 0 = fifo (first-in/first-out, or oldest messages first). 1 = l...

  • Page 619

    Issue 4.0 sv9100 programming manual 2-579 08 message waiting lamp (update mw lamp) enable/disable message waiting lamps at the extension associated with the subscriber mailbox. For subscriber mailboxes, enable this option. For guest mailboxes, disable this option. 0 = no (disable) 1 = yes (enable) 1...

  • Page 620

    Issue 4.0 2-580 program 47 : inmail 14 next call routing mailbox (next cr mbox) assign a next call routing mailbox to the subscriber mailbox. This provides callers with additional dialing options while listening to a subscriber mailbox recorded or default greeting. The digits the caller can dial dep...

  • Page 621

    Issue 4.0 sv9100 programming manual 2-581 28 station mailbox message notification options - queuing. Use this option to enable or disable message notification queuing. If enabled, message notification is stored in queue when there is no active notification destination. 0 = disabled 1 = enabled 0 tab...

  • Page 622

    Issue 4.0 2-582 program 47 : inmail conditions none feature cross reference none.

  • Page 623: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-583 description use 47-03 : sv8100 inmail group mailbox options to set up the 32 group mailboxes (01~32). A group mailbox is used for department group overflow and can be a subscriber or call routing. Conditions none feature cross reference none program 47 : inm...

  • Page 624: Program 47 : Inmail

    Issue 4.0 2-584 program 47 : inmail description use 47-06 : group mailbox subscriber options to set up a master mailbox assigned as a subscriber mailbox in 47-03-03: master mailbox type. Program 47 : inmail 47-06 : group mailbox subscriber options level: in input data group mailbox number 1~32 input...

  • Page 625

    Issue 4.0 sv9100 programming manual 2-585 04 message retention determine how long a subscriber mailbox retains held and saved messages. If a message is left in a subscriber mailbox longer than this interval, vm8000 inmail deletes it. 1~99 days 0 (indefinite) 0 05 recording conversation beep (rec con...

  • Page 626

    Issue 4.0 2-586 program 47 : inmail 08 forced unscreened transfer (forced utrf) enable/disable automated attendant forced unscreened transfer for the subscriber mailbox. If enabled, each screened transfer (trf) to the extension is converted to an unscreened transfer (utrf). If disabled, screened tra...

  • Page 627

    Issue 4.0 sv9100 programming manual 2-587 16 paging option 0 = rna 1 = immediate 0 17 telephone user interface 0 = numeric interface 1 = mnemonic interface 0 18 enable e-mail notification 0 = no 1 = yes 0 19 e-mail address up to 48 characters. No setting 20 include message as attachment 0 = no 1 = y...

  • Page 628

    Issue 4.0 2-588 program 47 : inmail table 2-14 47-06-14 default table item name input data 47-06-14 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = german 10 = madrid span...

  • Page 629

    Issue 4.0 sv9100 programming manual 2-589 conditions none feature cross reference none.

  • Page 630: Program 47 : Inmail

    Issue 4.0 2-590 program 47 : inmail description use 47-07 : sv8100 inmail routing mailbox options to set up the 32 routing mailboxes. Routing mailboxes can be either announcement or call routing mailboxes. Program 47 : inmail 47-07 : sv8100 inmail routing mailbox options level: in input data routing...

  • Page 631

    Issue 4.0 sv9100 programming manual 2-591 conditions none table 2-15 47-07-03 default table item name input data 47-07-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = g...

  • Page 632

    Issue 4.0 2-592 program 47 : inmail feature cross reference none.

  • Page 633: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-593 description use 47-08 : call routing mailbox options to set the options for mailboxes assigned as call routing mailboxes in 47-07-02: routing mailbox type. Program 47 : inmail 47-08 : call routing mailbox options level: in input data routing mailbox number 1...

  • Page 634

    Issue 4.0 2-594 program 47 : inmail conditions none feature cross reference none 04 fax detection enable/disable fax detection for the call routing mailbox. In enabled, the sv8100 inmail automated attendant (when using this call routing mailbox) detects incoming fax cng tone. The fax call then route...

  • Page 635: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-595 description use 47-09 : announcement mailbox options to set the options for mailboxes assigned as announcement mailboxes in 47-07-02 : routing mailbox type. Program 47 : inmail 47-09 : announcement mailbox options level: in input data routing mailbox number ...

  • Page 636

    Issue 4.0 2-596 program 47 : inmail conditions none feature cross reference none 03 hang up after (hangup) along with next call routing mailbox and repeat count above, provide additional routing options to automated attendant callers. For more detail on this interaction, refer to direct announcement...

  • Page 637: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-597 description use 47-10 : sv8100 inmail trunk options to assign sv8100 inmail options for each trunk. Program 47 : inmail 47-10 : sv8100 inmail trunk options level: in input data trunk port number 1~400 item no. Item input data default 01 answer table assignme...

  • Page 638

    Issue 4.0 2-598 program 47 : inmail table 2-16 47-10-03 default table item name input data 47-10-03 voice prompt language 01 = us english 02 = uk english 03 = australian english 04 = french canadian 05 = dutch 06 = mexican spanish 07 = latin american spanish 08 = italian 09 = german 10 = madrid span...

  • Page 639

    Issue 4.0 sv9100 programming manual 2-599 conditions none feature cross reference none.

  • Page 640: Program 47 : Inmail

    Issue 4.0 2-600 program 47 : inmail description use 47-11 : vm8000 inmail answer table options to set options for the answer tables. Vm8000 inmail provides eight answer tables (1~16). To set up the schedules for each answer table, go to 47-12 : vm8000 inmail answer table schedule. Program 47 : inmai...

  • Page 641

    Issue 4.0 sv9100 programming manual 2-601 02 override mailbox category (override mb ctg) specify the category of the mailbox where automated attendant calls should route when you enable answer schedule override. Vm8000 inmail mailbox categories are subscriber mailbox, master mailbox, and routing mai...

  • Page 642

    Issue 4.0 2-602 program 47 : inmail 03 default mailbox category (default mb ctg) specify the category of mailbox used as the default mailbox. Vm8000 inmail mailbox categories are subscriber mailbox, master mailbox, and routing mailbox. Vm8000 inmail uses the default mailbox when an answer schedule i...

  • Page 643

    Issue 4.0 sv9100 programming manual 2-603 conditions none feature cross reference none.

  • Page 644: Program 47 : Inmail

    Issue 4.0 2-604 program 47 : inmail description use 47-12 : vm8000 inmail answer schedules to set up the vm8000 inmail automated attendant answer schedules. There are 12 answer tables, with up to 10 answer schedules in each answer table. Program 47 : inmail 47-12 :vm8000 inmail answer schedules leve...

  • Page 645

    Issue 4.0 sv9100 programming manual 2-605 01 (continued from previous page) 3. Date a type 3 answer schedule runs only on a specific day of the year. For this type of schedule, you select: the specific date the schedule should run. On the selected date, the time the schedule should start. On the sel...

  • Page 646

    Issue 4.0 2-606 program 47 : inmail 04 start day (entryxx start day) for range of days (type 2) answer schedules, select the day of the week the answer schedule should start. 1 = sunday 2 = monday 3 = tuesday 4 = wednesday 5 = thursday 6 = friday 7 = saturday answer table 1/schedule 1 = 2 all other ...

  • Page 647

    Issue 4.0 sv9100 programming manual 2-607 example type 1 (day of the week) answer schedule options type 1 (day of week) example in this example, answer table 1 routes calls as follows: schedule 1 uses routing mailbox 2 and runs sunday from 8:30am to 5:00pm. Schedule 2 uses subscriber mailbox 3 and r...

  • Page 648

    Issue 4.0 2-608 program 47 : inmail type 1 (day of week) example answer table 1 answer schedule 1 answer schedule 1 is a day of week schedule that runs sunday from 8:30am to 5:00pm. 47-12-01: entry01 schedule type = 1 47-12-02: entry01 mb ctg = 3 47-12-02: entry01 mb num = 2 47-12-03: entry01 day = ...

  • Page 649

    Issue 4.0 sv9100 programming manual 2-609 type 2 (range of days) answer schedule options type 2 (range of days) example in this example, answer table 1 routes calls as follows: schedule 1 uses routing mailbox 1 and runs sunday through wednesday from 8:30am to 5:00pm. Schedule 2 uses routing mailbox ...

  • Page 650

    Issue 4.0 2-610 program 47 : inmail type 2 (range of days) example answer table 1 answer schedule 1 answer schedule 1 is a range of days schedule that starts schedule that runs sunday through wednesday from 8:30am to 5:00pm. 47-12-01: entry01 schedule type = 2 47-12-02: entry01 mb ctg = 3 47-12-02: ...

  • Page 651

    Issue 4.0 sv9100 programming manual 2-611 type 3 (date) answer schedule options type 3 (date) example in this example, answer table 1 routes calls as follows: schedule 1 uses routing mailbox 1 and runs every day from 8:30am to 5:00pm. Schedule 2 uses routing mailbox 9 and runs only on christmas day ...

  • Page 652

    Issue 4.0 2-612 program 47 : inmail conditions none feature cross reference none.

  • Page 653: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-613 description use 47-13 : vm8000 inmail dial action tables to set up the vm8000 inmail dial action tables. The dial action table defines the options than an automated attendant caller can dial. A dial action table is associated with a call routing mailbox, whi...

  • Page 654

    Issue 4.0 2-614 program 47 : inmail dial action table actions trf action - screened transfer (1) (trf) use this action to allow an automated attendant caller to place a screened transfer to an extension. After an automated attendant caller dials an extension, vm8000 inmail calls (screens) the destin...

  • Page 655

    Issue 4.0 sv9100 programming manual 2-615 to have unscreened transfer call a specific extension, the corresponding number option should be that extension number. The caller then dials that single digit to reach the extension. For example, to have callers dial 8 to reach extension 303, for key 8 ente...

  • Page 656

    Issue 4.0 2-616 program 47 : inmail number option to log directly into a specific subscriber mailbox, enter the mailbox number in the corresponding number option. For example, to have key 4 log directly into subscriber mailbox 305, for key 4 enter logon for the action and 305 for the corresponding n...

  • Page 657

    Issue 4.0 sv9100 programming manual 2-617 to log into any valid call routing or subscriber mailbox, enter ixxx in the corresponding number option. For example, to allow callers to dial 1 plus any call routing or announcement mailbox number to go to, for key 1 enter goto for the action and ixxx for t...

  • Page 658

    Issue 4.0 2-618 program 47 : inmail conditions none defaults feature cross reference none dial action table default settings key dial action table 1 dial action tables 2~32 1 utrf to xxx (unscreened transfer to user-dialed extension) und (undefined) 2 und (undefined) und (undefined) 3 utrf to xxxx (...

  • Page 659: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-619 description use 47-15 : routing directory mailbox options to define the routing directory mailbox options. This data is referred if program 47-07-02 (routing master mailbox type) was set to type 4 (directory). For vm8000 inmail remote ccis extensions are not...

  • Page 660: Program 47 : Inmail

    Issue 4.0 2-620 program 47 : inmail description use 47-17 : routing distribution mailbox options to assign data when program 47-07-02 is set to 4 (distribution). When creating a distribution list, there can be no blank destinations within the list. The system considers a blank entry as the end of th...

  • Page 661: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-621 description use 47-18: vm8000 inmail smtp setup to set the smtp e-mail notification. Conditions none feature cross reference none program 47 : inmail 47-18 :vm8000 inmail smtp setup level: in input data item no. Item input data default 01 smtp enabled 0 = no...

  • Page 662: Program 47 : Inmail

    Issue 4.0 2-622 program 47 : inmail description use 47-19 : vm8000 inmail pop3 setup to set the inmail e-mail notification. Conditions none feature cross reference none program 47 : inmail 47-19 :vm8000 inmail pop3 setup level: in input data item no. Item input data default 01 server name up to 48 c...

  • Page 663: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-623 description use 47-20 : station mailbox message notification to set the inmail station mailbox message notification parameters. Program 47 : inmail 47-20 : station mailbox message notification level: in input data station mailbox number 1~896 index number 1~...

  • Page 664

    Issue 4.0 2-624 program 47 : inmail conditions none feature cross reference none 11 notification day of week tuesday 0 = disabled 1 = enabled 1 12 notification day of week wednesday 0 = disabled 1 = enabled 1 13 notification day of week thursday 0 = disabled 1 = enabled 1 14 notification day of week...

  • Page 665: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-625 description use 47-21 : station mailbox find-me follow-me options to set the inmail station mailbox message find-me follow-me parameters. Program 47 : inmail 47-21 : station mailbox find-me follow-me options level: in input data station mailbox number 1~896 ...

  • Page 666

    Issue 4.0 2-626 program 47 : inmail conditions none feature cross reference none 10 find-me follow-me day of week friday 0 = disabled 1 = enabled 1 11 find-me follow-me day of week saturday 0 = disabled 1 = enabled 1 item no. Item input data default.

  • Page 667: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-627 description use 47-22 : group mailbox notification options to set the inmail group mailbox message notification parameters. Program 47 : inmail 47-22 : group mailbox notification options level: in input data group mailbox number 1~32 index number 1~5 item no...

  • Page 668

    Issue 4.0 2-628 program 47 : inmail conditions none feature cross reference none 11 notification day of week tuesday 0 = disabled 1 = enabled 1 12 notification day of week wednesday 0 = disabled 1 = enabled 1 13 notification day of week thursday 0 = disabled 1 = enabled 1 14 notification day of week...

  • Page 669: Program 47 : Inmail

    Issue 4.0 sv9100 programming manual 2-629 description use 47-23 : group mailbox find-me follow-me options to set the inmail group mailbox message find-me follow-me parameters. Program 47 : inmail 47-23 : group mailbox find-me follow-me options level: in input data group mailbox number 1~32 index num...

  • Page 670

    Issue 4.0 2-630 program 47 : inmail conditions none feature cross reference none 10 find-me follow-me day of week friday 0 = disabled 1 = enabled 1 11 find-me follow-me day of week saturday 0 = disabled 1 = enabled 1 item no. Item input data default.

  • Page 671: Service

    Sv9100 programming manual 2-631 program: 50 description use program 50-01 : ccis system setting to set the availability of ccis in the univerge sv9100. No other ccis settings function if this program is disabled. Conditions none feature cross reference none program 50 : common channel interoffice si...

  • Page 672: Service

    Issue 4.0 2-632 program 50 : common channel interoffice signaling service description use program 50-02 : connecting system settings to define the settings for each ccis route id. Program 50 : common channel interoffice signaling service 50-02 : connecting system settings level: in input data ccis r...

  • Page 673

    Issue 4.0 sv9100 programming manual 2-633 conditions if 56k k-ccis is used, 24 multi-frame (esf) must be assigned in program 10-03-02. Dpc must be what the opc is on the opposite side of the link. Feature cross reference none.

  • Page 674: Service

    Issue 4.0 2-634 program 50 : common channel interoffice signaling service description use program 50-03 : ccis destination system settings to assign information of remote systems in a ccis network. Conditions none feature cross reference none program 50 : common channel interoffice signaling service...

  • Page 675: Service

    Issue 4.0 sv9100 programming manual 2-635 description use program 50-04 : ccis office code assignment to define the office code when the ccis network is constructed with an open numbering plan. Conditions this program is used only in an open numbering plan network. This should include the trunk acce...

  • Page 676: Service

    Issue 4.0 2-636 program 50 : common channel interoffice signaling service description use program 50-05 : ccis maximum call forwarding hop counter to define the maximum hop counter of call forwarding. Conditions none feature cross reference none program 50 : common channel interoffice signaling serv...

  • Page 677: Service

    Issue 4.0 sv9100 programming manual 2-637 description use program 50-06 : ccis feature availability to define the availability of ccis features. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-06 : ccis feature availability level: in item no....

  • Page 678: Service

    Issue 4.0 2-638 program 50 : common channel interoffice signaling service description use program 50-07 : ccis centralized billing center office to define the point code and ccis route id for the billing center office. Conditions none feature cross reference none program 50 : common channel interoff...

  • Page 679: Service

    Issue 4.0 sv9100 programming manual 2-639 description use program 50-08 : ccis centralized blf sending group assignment to define the destination of blf for the sending system. Eight sending systems can be registered in this program. Conditions none feature cross reference none program 50 : common c...

  • Page 680: Service

    Issue 4.0 2-640 program 50 : common channel interoffice signaling service description use program 50-09 : ccis centralized blf sending extension number assignment to define the extension number for sending blf messages. One extension number can have a sending switch for each sending group, which is ...

  • Page 681

    Issue 4.0 sv9100 programming manual 2-641 conditions none feature cross reference none.

  • Page 682: Service

    Issue 4.0 2-642 program 50 : common channel interoffice signaling service description use program 50-10 : ccis centralized blf interval time assignment to define the time to send blf messages. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-1...

  • Page 683: Service

    Issue 4.0 sv9100 programming manual 2-643 description use program 50-11 : ccis centralized day/night switching sending group assignment to define point code and ccis route id for sending day/night switching message. Conditions none feature cross reference none program 50 : common channel interoffice...

  • Page 684: Service

    Issue 4.0 2-644 program 50 : common channel interoffice signaling service description use program 50-12 : ccis centralized day/night mode to system mode assignment to define corresponding night mode to switch to when day/night mode switching message arrives. Conditions none feature cross reference n...

  • Page 685: Service

    Issue 4.0 sv9100 programming manual 2-645 description use program 50-13 : ccis centralized response timeout assignment to define the response timeout value. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-13 : ccis centralized response timeou...

  • Page 686: Service

    Issue 4.0 2-646 program 50 : common channel interoffice signaling service description use program 50-14 : ccis intercom digits for caller id call return to eliminate the 9 on caller id redial except for 7- and 8-digit extensions. Conditions none feature cross reference none program 50 : common chann...

  • Page 687: Service

    Issue 4.0 sv9100 programming manual 2-647 description use program 50-15 : ccis over ip basic information setting to set the basic parameters for ccis over ip. Conditions none feature cross reference none program 50 : common channel interoffice signaling service 50-15 : ccis over ip basic information...

  • Page 688

    Issue 4.0 2-648 program 50 : common channel interoffice signaling service.

  • Page 689: Program 51 : Netlink Service

    Sv9100 programming manual 2-649 program: 51 description use program 51-01 : netlink system property setting to define the parameters of the netlink feature. Program 51 : netlink service 51-01 : netlink system property setting level: in important ❍ each system must be set with its own information. ❍ ...

  • Page 690

    Issue 4.0 2-650 program 51 : netlink service conditions none feature cross reference none 04 signal transmit method 0 = immediate this is the default setting which does not use nagle algorithm. When this is enabled data packets are immediately sent across the network with no buffering delay. 1 = buf...

  • Page 691: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-651 description use program 51-02 : netlink system basic setup to set system data for each netlink system. Conditions none feature cross reference none program 51 : netlink service 51-02 : netlink system basic setup level: in input data system id 1~50 item no. I...

  • Page 692: Program 51 : Netlink Service

    Issue 4.0 2-652 program 51 : netlink service description use program 51-03 : netlink internet protocol address list setting to set the ip address of the netlink system. Conditions when there is no primary system yet, or fail over occurs, node list is referred to establish new link. This setting is n...

  • Page 693: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-653 description use program 51-04 : ip address setting of top priority primary system of netlink to set the ip address of the new primary system. Conditions none feature cross reference none program 51 : netlink service 51-04 : ip address setting of top priority...

  • Page 694: Program 51 : Netlink Service

    Issue 4.0 2-654 program 51 : netlink service description use program 51-05 : netlink timer settings to set the various timers in the netlink system. Conditions none program 51 : netlink service 51-05 : netlink timer settings level: in input data item no. Item input data default 01 keep alive sending...

  • Page 695

    Issue 4.0 sv9100 programming manual 2-655 feature cross reference none.

  • Page 696: Program 51 : Netlink Service

    Issue 4.0 2-656 program 51 : netlink service description use program 51-06 : netlink primary automatic integration setting to set the automatic integration of the primary system. Conditions none feature cross reference none program 51 : netlink service 51-06 : netlink primary automatic integration s...

  • Page 697: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-657 description use program 51-07 : netlink primary compulsion specification setting to set compulsion specification of the primary system. Conditions none feature cross reference none program 51 : netlink service 51-07 : netlink primary compulsion specification...

  • Page 698: Program 51 : Netlink Service

    Issue 4.0 2-658 program 51 : netlink service description use program 51-08 : primary netlink setting to set the ip address and system id of the compulsory specification of the primary system. Conditions none feature cross reference none program 51 : netlink service 51-08 : primary netlink setting le...

  • Page 699: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-659 description use program 51-09 : netlink communication port settings to set the various communication ports used on the system. Program 51 : netlink service 51-09 : netlink communication port settings level: in input data item no. Item input data default 01 p...

  • Page 700

    Issue 4.0 2-660 program 51 : netlink service conditions none feature cross reference none.

  • Page 701: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-661 description use program 51-10: virtual slot setting to view the number of virtual slots that are remaining in a netlink network. There can be up to 240 virtual slots available in netlink. Conditions this program is read only. Feature cross reference none pro...

  • Page 702: Program 51 : Netlink Service

    Issue 4.0 2-662 program 51 : netlink service description use program 51-11: netlink system information to reference information about other systems in the netlink network. Conditions this program is read only. Feature cross reference none program 51 : netlink service 51-11 : netlink system informati...

  • Page 703: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-663 description use program 51-12: primary system information to reference information about the primary system in the netlink network. Conditions this program is read only. Feature cross reference none program 51 : netlink service 51-12 : primary system informa...

  • Page 704: Program 51 : Netlink Service

    Issue 4.0 2-664 program 51 : netlink service description use program 51-13: netlink options to enable automatic ip address list operation updates, time zone information, and mac address authorization. Conditions none feature cross reference none program 51 : netlink service 51-13 : netlink options l...

  • Page 705: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-665 description use program 51-14: netlink system control to delete system and slot information. Conditions none feature cross reference none program 51 : netlink service 51-14 : netlink system control level: in important this program is available only via telep...

  • Page 706: Program 51 : Netlink Service

    Issue 4.0 2-666 program 51 : netlink service description use program 51-15: demonstration setting to automatically set the minimum setting values in netlink. A system reset occurs after this command is executed. Conditions none feature cross reference none program 51 : netlink service 51-15 : demons...

  • Page 707: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-667 description use program 51-16: netlink system data replication mode setting to set the system data replication between the primary and secondary systems. Program 51 : netlink service 51-16 : netlink system data replication mode setting level: in input data i...

  • Page 708

    Issue 4.0 2-668 program 51 : netlink service conditions none feature cross reference none.

  • Page 709: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-669 description use program 51-17: netlink dt800/dt700 server individual information setup to set the netlink port information. Conditions none feature cross reference none program 51 : netlink service 51-17 : netlink dt80/dt700 server individual information set...

  • Page 710: Program 51 : Netlink Service

    Issue 4.0 2-670 program 51 : netlink service description use program 51-18: netlink configuration options to set the netlink fail-over limits. Conditions none feature cross reference none program 51 : netlink service 51-18 : netlink configuration options level: in input data item no. Item input data...

  • Page 711: Program 51 : Netlink Service

    Issue 4.0 sv9100 programming manual 2-671 description use program 51-19: netlink ip trunk (sip) calling party number setup for extension to set cpn transmission for each secondary system. Conditions none feature cross reference none program 51 : netlink service 51-19 : netlink ip trunk (sip) calling...

  • Page 712

    Issue 4.0 2-672 program 51 : netlink service.

  • Page 713: 80-01 : Service Tone Setup

    Sv9100 programming manual 2-673 program: 80 description use program 80-01 : service tone setup to define up to 64 service tones. Each service tone is defined by the combination of 32 basic tones. Program 80 : basic hardware setup for system 80-01 : service tone setup level: in input data service ton...

  • Page 714

    Issue 4.0 2-674 program 80 : basic hardware setup for system table 2-17 basic tones basic tone no. Frequency (hz) level (db) basic tone no. Frequency (hz) level (db) 01 400 - 13 17 520 / 650 -13 / -19 02 520 -13 18 650 / 780 -13 / -19 03 580 -13 19 780 / 1040 -13 / -19 04 660 -13 20 1040 -13 05 700 ...

  • Page 715

    Issue 4.0 sv9100 programming manual 2-675 default service tone no. Service tone repeat count unit count basic tone no. Duration gain level (db) 1 no tone 0 basic 1 0 10 32 (0db) 2 internal dial tone 0 basic 1 9 10 32 (0db) 3 stutter dial tone 0 basic 6 0 9 0 9 0 9 2 1 1 1 1 77 32 (0db) 4 internal re...

  • Page 716

    Issue 4.0 2-676 program 80 : basic hardware setup for system 19 door box chime 1 3 basic 6 4 4 2 2 2 0 2 2 3 4 6 5 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (0db) 20 door box chime 2 3 basic 6 7 7 5 5 5 0 2 2 3 4 6 5 38 (+3db) 26 (-3db) 38 (+3db) 26 (-3db) 14 (-9db) 32 (0db) 21 door box c...

  • Page 717

    Issue 4.0 sv9100 programming manual 2-677 30 door box call tone 1 basic 2 0 6 1 1 32 (0db) 32 (0db) 31 paging tone 2 basic 2 0 6 1 1 32 (0db) 32 (0db) 32 splash tone 1 1 basic 2 0 6 1 1 32 (0db) 32 (0db) 33 splash tone 2 2 basic 2 0 6 1 1 32 (0db) 32 (0db) 34 splash tone 3 3 basic 2 0 6 1 1 32 (0db)...

  • Page 718

    Issue 4.0 2-678 program 80 : basic hardware setup for system 51 external intercept tone 0 2 12 4 3 2 32 (0db) 32 (0db) 52 external call waiting tone 1 1 12 3 32 (0db) 53 external executive override tone 1 1 12 10 32 (0db) 54 progress tone 0 2 0 1 6 1 32 (0db) 32 (0db) 55 generate tone for tapi2.1 0 ...

  • Page 719

    Issue 4.0 sv9100 programming manual 2-679 conditions the system must be reset for any change to these items to take affect. Feature cross reference selectable ring tones.

  • Page 720: 80-02 : Dtmf Tone Setup

    Issue 4.0 2-680 program 80 : basic hardware setup for system description use program 80-02 : dtmf tone setup to define the duration (on time) and pause (off time) for dtmf dialing. This option affects all trunk line calls system wide. Make separate entries for duration and pause. It is also possible...

  • Page 721

    Issue 4.0 sv9100 programming manual 2-681 conditions none feature cross reference none.

  • Page 722

    Issue 4.0 2-682 program 80 : basic hardware setup for system description use program 80-03 : dtmf tone receiver setup to define the various levels and timers for the dtmf tone receiver. Dtmf tone receiver type: 1 = dtmf receiver for extension 2 = dtmf receiver for analog trunk 3 = dtmf receiver for ...

  • Page 723

    Issue 4.0 sv9100 programming manual 2-683 03 min. Detect level 0~15 detect level 0 : -10dbm(0) to -25dbm(15) detect level 1 : -15dbm(0) to -30dbm(15) detect level 2 : -20dbm(0) to -35dbm(15) detect level 3 : -25dbm(0) to -40dbm(15) detect level 4 : -30dbm(0) to -45dbm(15) detect level 5 : -35dbm(0) ...

  • Page 724

    Issue 4.0 2-684 program 80 : basic hardware setup for system default conditions none feature cross reference none item no item type 1 type 2 type 3 type 4 type 5 01 detect level 0 0 0 0 0 02 start delay time 0 0 0 0 1 03 min. Detect level 10 (-20dbm) 15 (-25dbm) 15 (-25dbm) 10 (-20dbm) 10 (-20dbm) 0...

  • Page 725

    Issue 4.0 sv9100 programming manual 2-685 description use program 80-04 : call progress tone detector setup to define the various levels and timers for the call progress tone detector. Tone detector type: 1 = dial tone for trunk 2 = busy tone for trunk 3 = ring back tone for trunk 4 = special busy t...

  • Page 726

    Issue 4.0 2-686 program 80 : basic hardware setup for system 02 min. Detection level 0~15 0 = -10dbm(0) to -25dbm(15) 1 = -15dbm(0) to -30dbm(15) 2 = -20dbm(0) to -35dbm(15) 3 = -25dbm(0) to -40dbm(15) 4 = -30dbm(0) to -45dbm(15) 5 = -35dbm(0) to -50dbm(15) 6 = -40dbm(0) to -55dbm(15) 03 s/n ratio 0...

  • Page 727

    Issue 4.0 sv9100 programming manual 2-687 default conditions none feature cross reference none item name type 1 (dt) type 2 (bt) type 3 (rbt) type 4 type 5 1 detect level 0 (-25dbm) 0 (-25dbm) 0 (-25dbm) 0 (-25dbm) 0 2 min. Detect level 15 (-25dbm) 15 (-25dbm) 15 (-25dbm) 15 (-25dbm) 0 (version 1000...

  • Page 728

    Issue 4.0 2-688 program 80 : basic hardware setup for system description use program 80-05 : date format for smdr and system to define the date format when printing out the smdr, alarm report, and system information report. Conditions none feature cross reference none program 80 : basic hardware set...

  • Page 729

    Issue 4.0 sv9100 programming manual 2-689 description use program 80-07 : call progress tone detector frequency setup to set the frequency of the detection tone set with program 80-04-12 and program 80-04-13. Conditions none feature cross reference none program 80 : basic hardware setup for system 8...

  • Page 730: 80-09 : Short Ring Setup

    Issue 4.0 2-690 program 80 : basic hardware setup for system description use program 80-09 : short ring setup to define the short ring tone for sv9100 multiline terminals. Program 80 : basic hardware setup for system 80-09 : short ring setup level: in input data short ring tone 1 = confirmation 2 = ...

  • Page 731

    Issue 4.0 sv9100 programming manual 2-691 03 494 11 1046 04 523 12 1175 05 587 13 1318 06 659 14 1397 07 698 15 1568 08 784 table 2-19 ring cycle table data ring cycle (ms) 01 125(on)/off 02 125(on)/125(off)/125(on)/off 03 125(on)/125(off)/125(on)/125(off)/125(on)/off 04 125(on)/125(off)/125(on)/125...

  • Page 732

    Issue 4.0 2-692 program 80 : basic hardware setup for system conditions none feature cross reference none : : : : : 32 not defined 0 0 0

  • Page 733

    Issue 4.0 sv9100 programming manual 2-693 description use program 80-10 : dtmf tone receiver setup to set various data for the dtmf signal detection. Program 80 : basic hardware setup for system 80-10 : dtmf tone receiver setup level: mf input data dtmf tone receiver type number 1 = dtmf receiver fo...

  • Page 734

    Issue 4.0 2-694 program 80 : basic hardware setup for system conditions none feature cross reference none 06 s/n ratio 0~4 (-5step, 0db~ -20db) 07 on detect time 1~255 (15step, 30ms~3840ms) 08 off detect time 1~255 (15step, 30ms~3840ms) table 2-20 default table item name type 1 type 2 type 3 type 4 ...

  • Page 735

    Issue 4.0 sv9100 programming manual 2-695 description use program 80-13 : dtmf tone receiver setup - 2 to set further data for the dtmf signal detection. Conditions none feature cross reference none program 80 : basic hardware setup for system 80-13 : dtmf tone receiver setup - 2 level: mf item no. ...

  • Page 736

    Issue 4.0 2-696 program 80 : basic hardware setup for system description use program 80-14 : mf tone receiver setup -3 to set further data for the dtmf signal detection. Conditions none feature cross reference none program 80 : basic hardware setup for system 80-14 : dtmf tone receiver setup - 3 lev...

  • Page 737

    Sv9100 programming manual 2-697 program: 81 description use program 81-01 : cot initial data setup to define the various basic data parameters for the cot (co blade) unit. Program 81 : basic hardware setup for trunk 81-01 : cot initial data setup level: mf input data item no. Item input data default...

  • Page 738

    Issue 4.0 2-698 program 81 : basic hardware setup for trunk 13 grounding time 1~255 (16~4080ms) 9 (144ms) 14 hook flash 1 time 1~255 (16~4080ms) 50 (800ms) 15 hook flash 2 time 1~255 (16~4080ms) 156 (2496ms) 16 pause time 1~255 (64~16320ms) 16 (1024ms) 17 pft idle detection time 1~255 (64~16320ms) 4...

  • Page 739

    Issue 4.0 sv9100 programming manual 2-699 conditions none feature cross reference none 30 dial pulse break time (20pps) 1~255 (8~2040ms) 4 (32ms) 31 dial pulse make time (20pps) 1~255 (8~2040ms) 2 (16ms) 32 dp inter-digit time (20pps) 1~255 (32~8160ms) 16 (512ms) 33 charging pulse minimum duration 1...

  • Page 740

    Issue 4.0 2-700 program 81 : basic hardware setup for trunk description use program 81-02 : diopu initial data setup to define the various basic timers for the did unit. Program 81 : basic hardware setup for trunk 81-02 : diopu initial data setup level: mf input data item name input data default 01 ...

  • Page 741

    Issue 4.0 sv9100 programming manual 2-701 conditions none feature cross reference none 14 receive dp break minimum time 1~255 (2~510ms) 5 (10ms) 15 receive dp break maximum time 1~255 (2~510ms) 50 (100ms) 16 receive dp inter-digit time 1~255 (32~8160ms) 6 (192ms) 17 loop off guard time 0~25 (0,100~2...

  • Page 742

    Issue 4.0 2-702 program 81 : basic hardware setup for trunk description use program 81-03 : tli initial data setup to define the various basic timers for the e&m tie line unit. Program 81 : basic hardware setup for trunk 81-03 : tli initial data setup level: in input data item name input data defaul...

  • Page 743

    Issue 4.0 sv9100 programming manual 2-703 conditions none feature cross reference none 14 receive dp make maximum time 1~255 (2~510ms) 50 (100ms) 15 receive dp break minimum time 1~255 (2~510ms) 5 (10ms) 16 receive dp break maximum time 1~255 (2~510ms) 50 (100ms) 17 pause time after wink/delay recei...

  • Page 744

    Issue 4.0 2-704 program 81 : basic hardware setup for trunk description use program 81-04 : isdn bri layer 1 (t-point) initial data setup to define the various basic data for layer 1 of isdn bri. Conditions none feature cross reference none program 81 : basic hardware setup for trunk 81-04 : isdn br...

  • Page 745

    Issue 4.0 sv9100 programming manual 2-705 description use program 81-05 : isdn bri & pri layer 2 (t-point) initial data setup to define the various basic data for layer 2 of isdn bri and pri. Conditions none feature cross reference none program 81 : basic hardware setup for trunk 81-05 : isdn bri & ...

  • Page 746

    Issue 4.0 2-706 program 81 : basic hardware setup for trunk description use program 81-06 : isdn bri & pri layer 3 (t-point) timer setup to define the various basic timers for layer 3 of isdn bri/pri (defined in program 10-03-04). Program 81 : basic hardware setup for trunk 81-06 : isdn bri & pri la...

  • Page 747

    Issue 4.0 sv9100 programming manual 2-707 conditions none feature cross reference isdn compatibility 11 t312 specify the timer value started when setup is sent or re-sent on broadcast data link. This timer is valid only for network side use only. 1~254 (sec) 6 12 t313 specify the timer value started...

  • Page 748

    Issue 4.0 2-708 program 81 : basic hardware setup for trunk description use program 81-07 : codec filter setup for analog trunk port to define the codec (qslac) filter for each analog trunk port. Conditions none feature cross reference none program 81 : basic hardware setup for trunk 81-07 : codec f...

  • Page 749: 81-08 : T1 Trunk Timer Setup

    Issue 4.0 sv9100 programming manual 2-709 description use program 81-08 : t1 trunk timer setup to define the basic timer setting of each t1 trunk type. Program 81 : basic hardware setup for trunk 81-08 : t1 trunk timer setup level: in input data item name input data default 01 answer signal detectio...

  • Page 750

    Issue 4.0 2-710 program 81 : basic hardware setup for trunk 14 ringing signal detection time (e&m) 1~250 (8ms ~ 2000ms) 10 80ms 15 ringing signal detection time (opx) 1~250 (8ms ~ 2000ms) 10 80ms 16 ringing signal stop detection time (loop) 1~255 (100ms ~ 25500ms) 50 5000ms 17 ringing signal stop de...

  • Page 751

    Issue 4.0 sv9100 programming manual 2-711 33 hookflash send time (opx) 1~255 (100ms ~ 25500ms ) 5 500ms 34 pause send time (all) 1~255 (1sec ~ 255sec ) 3 3sec 35 wink send duration time (did) 1~250 (8ms ~ 2000ms) 25 200ms 36 delay send duration time (did) 1~250 (8ms ~ 2000ms) 25 200ms 37 incoming-wi...

  • Page 752

    Issue 4.0 2-712 program 81 : basic hardware setup for trunk 52 receive hookflash duration min. Time (e&m) 1~255 (100ms ~ 25500ms) 3 300ms 53 receive hookflash duration max. Time (e&m) 1~255 (100ms ~ 25500ms) 6 600ms 54 receive hookflash duration min. Time (opx) 1~255 (100ms ~ 25500ms) 3 300ms 55 rec...

  • Page 753

    Issue 4.0 sv9100 programming manual 2-713 conditions none feature cross reference none 71 guard time 1 (ground) 1~255 (100ms ~ 25500ms) 9 900ms 72 guard time 1 (did) 1~250 (4ms ~ 1000ms) 3 12ms 73 guard time 1 (e&m) 1~255 (100ms ~ 25500ms) 20 2000ms 74 guard time 1 (opx) 1~255 (100ms ~ 25500ms) 40 4...

  • Page 754

    Issue 4.0 2-714 program 81 : basic hardware setup for trunk description use program 81-09 : cot codec (qslac) filter setting to define the filter setting data (when program 81-07 is set to 4). Program 81 : basic hardware setup for trunk 81-09 : cot codec (qslac) filter setting level: in input data i...

  • Page 755

    Issue 4.0 sv9100 programming manual 2-715 21 z filter coefficients(4) 0~255 164 22 z filter coefficients(5) 0~255 202 23 z filter coefficients(6) 0~255 181 24 z filter coefficients(7) 0~255 170 25 z filter coefficients(8) 0~255 78 26 z filter coefficients(9) 0~255 51 27 z filter coefficients(10) 0~2...

  • Page 756

    Issue 4.0 2-716 program 81 : basic hardware setup for trunk conditions this is used if program 81-07 is set to 4 (specified data). Feature cross reference none 51 x filter coefficients(5) 0~255 42 52 x filter coefficients(6) 0~255 45 53 x filter coefficients(7) 0~255 170 54 x filter coefficients(8) ...

  • Page 757

    Issue 4.0 sv9100 programming manual 2-717 description use program 81-14 : diopu (ld trunk) codec (qslac) filter data setup to define the codec filter data. Program 81 : basic hardware setup for trunk 81-14 : diopu (ld trunk) codec (qslac) filter data setup level: in input data item no. Item input da...

  • Page 758

    Issue 4.0 2-718 program 81 : basic hardware setup for trunk 21 z filter coefficients(4) 0~255 135 22 z filter coefficients(5) 0~255 162 23 z filter coefficients(6) 0~255 55 24 z filter coefficients(7) 0~255 90 25 z filter coefficients(8) 0~255 151 26 z filter coefficients(9) 0~255 170 27 z filter co...

  • Page 759

    Issue 4.0 sv9100 programming manual 2-719 conditions this program is valid when program 81-07 is set to filter type 4. This program is not valid when program 81-17 is set to option type 5~15. Feature cross reference none 52 x filter coefficients(6) 0~255 144 53 x filter coefficients(7) 0~255 1 54 x ...

  • Page 760

    Issue 4.0 2-720 program 81 : basic hardware setup for trunk description use program 81-15 : tliu(2w) codec (qslac) filter data setup to define the tliu (2w) codec (qslac) filter data. Program 81 : basic hardware setup for trunk 81-15 : tliu(2w) codec (qslac) filter data setup level: in input data it...

  • Page 761

    Issue 4.0 sv9100 programming manual 2-721 21 z filter coefficients(4) 0~255 213 22 z filter coefficients(5) 0~255 170 23 z filter coefficients(6) 0~255 54 24 z filter coefficients(7) 0~255 34 25 z filter coefficients(8) 0~255 190 26 z filter coefficients(9) 0~255 166 27 z filter coefficients(10) 0~2...

  • Page 762

    Issue 4.0 2-722 program 81 : basic hardware setup for trunk conditions this program is valid when program 81-07 is set to filter type 4. This program is not valid when program 81-17 is set to option type 5~15. Feature cross reference none 52 x filter coefficients(6) 0~255 144 53 x filter coefficient...

  • Page 763

    Issue 4.0 sv9100 programming manual 2-723 description use program 81-16 : tliu(4w) codec (qslac) filter data setup to define the tliu (2w) codec (qslac) filter data. Program 81 : basic hardware setup for trunk 81-16 : tliu(4w) codec (qslac) filter data setup level: in input data item no. Item input ...

  • Page 764

    Issue 4.0 2-724 program 81 : basic hardware setup for trunk 21 z filter coefficients(4) 0~255 144 22 z filter coefficients(5) 0~255 1 23 z filter coefficients(6) 0~255 144 24 z filter coefficients(7) 0~255 1 25 z filter coefficients(8) 0~255 144 26 z filter coefficients(9) 0~255 1 27 z filter coeffi...

  • Page 765

    Issue 4.0 sv9100 programming manual 2-725 conditions this program is valid when program 81-07 is set to filter type 4. This program is not valid when program 81-17 is set to option type 5~15. Feature cross reference none 52 x filter coefficients(6) 0~255 144 53 x filter coefficients(7) 0~255 1 54 x ...

  • Page 766

    Issue 4.0 2-726 program 81 : basic hardware setup for trunk description use program 81-17 : codec filter option data type setup to define the codec filter option data type. Conditions none feature cross reference none program 81 : basic hardware setup for trunk 81-17 : codec filter option data type ...

  • Page 767: 82-01 : Incoming Ring Tone

    Sv9100 programming manual 2-727 program: 82 description use program 82-01 : incoming ring tone to set the incoming ring tones, which are the tones a user hears when a call rings an extension. These tones are grouped into four ring tone ranges (1~4), also called patterns, that consist of a combinatio...

  • Page 768

    Issue 4.0 2-728 program 82 : basic hardware setup for extension conditions none 03 modulation 0 = no modulation 1 = 8hz modulation 2 = 16hz modulation 3 = envelope default incoming ringing tone number tone type frequency 1 (hz) frequency 2 (hz) modulation pattern 1 (trunk incoming) high mid low 1100...

  • Page 769

    Issue 4.0 sv9100 programming manual 2-729 feature cross reference distinctive ringing tones and flash patterns selectable ring tones.

  • Page 770

    Issue 4.0 2-730 program 82 : basic hardware setup for extension description use program 82-03 : dss console led pattern setup to define the led patterns for special functions on a dss console. Led pattern 0 : [off] led pattern 1 : [fl: on(500ms)/off(500ms)] led pattern 2 : [wk: on(250ms)/off(250ms)]...

  • Page 771

    Issue 4.0 sv9100 programming manual 2-731 led pattern 4 : [ir: on(125ms)/off(125ms)/on(125ms)/off(625ms)] led pattern 5 : [il: on(875ms)/off(125ms)] led pattern 6 : [iw: on(625ms)/off(125ms)/on(125ms)/off(125ms)] led pattern 7 : [on] conditions none feature cross reference direct station selection (...

  • Page 772

    Issue 4.0 2-732 program 82 : basic hardware setup for extension description use program 82-04 : lca initial data setup to set the basic data of the lca. Program 82 : basic hardware setup for extension 82-04 : lca initial data setup level: mf input data item no. Item input data default 01 companding ...

  • Page 773

    Issue 4.0 sv9100 programming manual 2-733 conditions none feature cross reference none.

  • Page 774

    Issue 4.0 2-734 program 82 : basic hardware setup for extension description use program 82-05 : isdn bri layer 2 initial setup to set the various basic data for layer 2 of isdn/ pri s-point conditions none feature cross reference none program 82 : basic hardware setup for extension 82-05 : isdn bri ...

  • Page 775

    Issue 4.0 sv9100 programming manual 2-735 description use program 82-06 : isdn bri layer 3 timer setup to set the various basic timers for layer 3 of isdn bri/pri s-point. Program 82 : basic hardware setup for extension 82-06 : isdn bri layer 3 timer setup level: mf input data item no. Item input da...

  • Page 776

    Issue 4.0 2-736 program 82 : basic hardware setup for extension conditions none feature cross reference none.

  • Page 777

    Issue 4.0 sv9100 programming manual 2-737 description use program 82-07 : codec filter setup for analog station port to set the filter value of the codec (qslac) filter of each analog port. Conditions none feature cross reference direct station selection (dss) program 82 : basic hardware setup for e...

  • Page 778

    Issue 4.0 2-738 program 82 : basic hardware setup for extension description use program 82-08 : sidetone volume setup for adjusting the telephone sidetone volume. There are two levels, based on whether the connected trunk is a digital trunk or analog trunk. Conditions none feature cross reference ce...

  • Page 779

    Issue 4.0 sv9100 programming manual 2-739 description use program 82-09 : lca codec filter data setup to define the filter setting data (when program 82-07 is set to 4). Program 82 : basic hardware setup for extension 82-09 : lca codec filter data setup level: in input data item name input data defa...

  • Page 780

    Issue 4.0 2-740 program 82 : basic hardware setup for extension 21 z filter coefficients(4) 0~255 163 22 z filter coefficients(5) 0~255 59 23 z filter coefficients(6) 0~255 194 24 z filter coefficients(7) 0~255 196 25 z filter coefficients(8) 0~255 195 26 z filter coefficients(9) 0~255 170 27 z filt...

  • Page 781

    Issue 4.0 sv9100 programming manual 2-741 conditions this is used if program 82-07 is set to 4 (specified data). Feature cross reference none 51 x filter coefficients(5) 0~255 42 52 x filter coefficients(6) 0~255 135 53 x filter coefficients(7) 0~255 35 54 x filter coefficients(8) 0~255 52 55 x filt...

  • Page 782

    Issue 4.0 2-742 program 82 : basic hardware setup for extension description use program 82-14 : handset/headset gain for multiline telephone to set the sending and receiving gain of the multiline telephone handset. Conditions none feature cross reference none program 82 : basic hardware setup for ex...

  • Page 783

    Issue 4.0 sv9100 programming manual 2-743 description use program 82-15 : opx codec (qslac) filter data setup to define the filter data setup information (when program 82-07 is set to 4). Program 82 : basic hardware setup for extension 82-15 : opx codec (qslac) filter data setup level: in input data...

  • Page 784

    Issue 4.0 2-744 program 82 : basic hardware setup for extension 21 z filter coefficients(4) 0~255 35 22 z filter coefficients(5) 0~255 69 23 z filter coefficients(6) 0~255 162 24 z filter coefficients(7) 0~255 210 25 z filter coefficients(8) 0~255 165 26 z filter coefficients(9) 0~255 202 27 z filte...

  • Page 785

    Issue 4.0 sv9100 programming manual 2-745 conditions none feature cross reference none 51 x filter coefficients(5) 0~255 1 52 x filter coefficients(6) 0~255 144 53 x filter coefficients(7) 0~255 1 54 x filter coefficients(8) 0~255 144 55 x filter coefficients(9) 0~255 1 56 x filter coefficients(10) ...

  • Page 786

    Issue 4.0 2-746 program 82 : basic hardware setup for extension description use program 82-16 : sli codec (qslac) filter data setup to define the filter data setup information (when program 82-07 is set to 4). Program 82 : basic hardware setup for extension 82-16 : sli codec (qslac) filter data setu...

  • Page 787

    Issue 4.0 sv9100 programming manual 2-747 21 z filter coefficients(4) 0~255 163 22 z filter coefficients(5) 0~255 59 23 z filter coefficients(6) 0~255 194 24 z filter coefficients(7) 0~255 196 25 z filter coefficients(8) 0~255 195 26 z filter coefficients(9) 0~255 170 27 z filter coefficients(10) 0~...

  • Page 788

    Issue 4.0 2-748 program 82 : basic hardware setup for extension conditions none feature cross reference none 51 x filter coefficients(5) 0~255 42 52 x filter coefficients(6) 0~255 135 53 x filter coefficients(7) 0~255 35 54 x filter coefficients(8) 0~255 52 55 x filter coefficients(9) 0~255 71 56 x ...

  • Page 789

    Issue 4.0 sv9100 programming manual 2-749 description use program 81-17 : codec filter option data type setup to define the codec filter option data type. Conditions none feature cross reference none program 82 : basic hardware setup for extension 82-17 : codec filter option data type setup level: i...

  • Page 790

    Issue 4.0 2-750 program 82 : basic hardware setup for extension.

  • Page 791

    Sv9100 programming manual 2-751 program: 84 description use program 84-01 : h.323 trunk basic information setup to set the basic information of the h.323 trunk. Program 84 : hardware setup for voip 84-01 : h.323 trunk basic information setup level: in input data item no. Item input data default 02 n...

  • Page 792

    Issue 4.0 2-752 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip) 22 vad threshold 0~30 (-19db~ +10db and self adjustment) 0 = self adjustment 1 = -19db (-49dbm) : 20 = 0db (-30dbm) : 29 = 9db (-21dbm) 30 = 10db (-20dbm) 20 33 priority c...

  • Page 793

    Issue 4.0 sv9100 programming manual 2-753 description use program 84-02 : h.225 and h.245 information basic setup to define the basic setup information of h.225 and h.245. Program 84 : hardware setup for voip 84-02 : h.225 and h.245 information basic setup level: in input data item no. Item input da...

  • Page 794

    Issue 4.0 2-754 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip) 22 arq retry count 0~255 2 23 ras brq timer 0~255sec 5 24 brq retry count 0~255 2 25 ras irr timer 0~255sec 5 26 irr retry count 0~255 2 27 ras drq timer 0~255sec 8 28 drq...

  • Page 795: 84-06 : Pva Data Setting

    Issue 4.0 sv9100 programming manual 2-755 description use program 84-06 : pva data setting to set up threshold levels of every cd-pvaa slot. Conditions system programming must be exited before these program options take affect. Feature cross reference voice over internet protocol (voip) program 84 :...

  • Page 796

    Issue 4.0 2-756 program 84 : hardware setup for voip description use program 84-07 : firmware download setup to configure the settings related to central firmware download for ip phones. Conditions none feature cross reference none program 84 : hardware setup for voip 84-07 : firmware download setup...

  • Page 797: 84-09 : Vlan Setup

    Issue 4.0 sv9100 programming manual 2-757 description use program 84-09 : vlan setup to set up the vlan data for ethernet interface ports. Conditions system programming must be exited before these program options take affect. Feature cross reference voice over internet protocol (voip) program 84 : h...

  • Page 798: 84-10 : Tos Setup

    Issue 4.0 2-758 program 84 : hardware setup for voip description use program 84-10 : tos setup to set up the type of service data. Program 84 : hardware setup for voip 84-10 : tos setup level: in input data protocol type 1 = not used 2 = not used 3 = voice control 4 = h.323 5 = rtp/rtcp 6 = sip 7 = ...

  • Page 799

    Issue 4.0 sv9100 programming manual 2-759 conditions the system must be reset for these program options to take affect. Feature cross reference voice over internet protocol (voip).

  • Page 800

    Issue 4.0 2-760 program 84 : hardware setup for voip description use program 84-12 : networking codec information basic setup to set voice (rtp packet) encoding parameters. Program 84 : hardware setup for voip 84-12 : networking codec information basic setup level: in item no. Item input data defaul...

  • Page 801

    Issue 4.0 sv9100 programming manual 2-761 conditions none feature cross reference voice over internet protocol (voip) 28 audio capability priority 0 = g.711_pt 2 = g.729_pt 3 = g.722_pt 0 35 g.722 jitter buffer (min) 0~300ms 30 36 g.722 jitter buffer (average) 0~300ms 60 37 g.722 jitter buffer (max)...

  • Page 802

    Issue 4.0 2-762 program 84 : hardware setup for voip description use program 84-13 : sip trunk codec information basic setup to set up the basic codec options for sip trunks. Program 84 : hardware setup for voip 84-13 : sip trunk codec information basic setup level: in input data item no. Item input...

  • Page 803

    Issue 4.0 sv9100 programming manual 2-763 18 vad threshold 0~30 (-19db~+10db) 0 = self adjustment 1 = -19db (-49dbm) : 2 = 0db (-30dbm) : 29 = 9dbm (-21dbm) 30 = 10dbm (-20dbm) 20 28 audio capability priority 0 = g.711_pt 2 = g.729_pt 3 = g.722_pt 4 = g.726_pt 6 = g.711_fix 7 = g.729_fix 0 33 number...

  • Page 804

    Issue 4.0 2-764 program 84 : hardware setup for voip 65 vad negotiation on sdp select whether or not system uses sip negotiation for vad usage. When set to '0 = disable' system disregards sip negotiation result and always enables the vad. When set to'1 = enable' system uses sip negotiation and decid...

  • Page 805

    Issue 4.0 sv9100 programming manual 2-765 72 jitter buffer mode for video this program is not supported for version 1.00 software and will be supported in a later release. This program sets the jitter buffer size adjustment. At default this is set to self adjusting and should only be changed when di...

  • Page 806

    Issue 4.0 2-766 program 84 : hardware setup for voip conditions none feature cross reference none 75 maximum jitter buffer for video this program is not supported for version 1.00 software and will be supported in a later release. This program sets the maximum value of jitter buffer for the video st...

  • Page 807

    Issue 4.0 sv9100 programming manual 2-767 description use program 84-14 : sip trunk basic information setup to define the basic setup for sip trunks. Program 84 : hardware setup for voip 84-14 : sip trunk basic information setup level: in input data item no. Item input data default profile 1~6 06 si...

  • Page 808

    Issue 4.0 2-768 program 84 : hardware setup for voip 13 e.164 incoming/outgoing via sip trunk uri when making an incoming or outgoing call via sip trunk, enable or disable conversion of sip-uri to from e.164 format (e.G. +850xxxx) for pstn. When making an outgoing call at sip trunk, add ‘+’ and inte...

  • Page 809

    Issue 4.0 sv9100 programming manual 2-769 conditions none feature cross reference none 17 call forward moved temporarily support input data 1: when enabled a 302 moved temporarily response is sent for external call forward destinations. 0 = disabled 1 = 302 return 0 18 keep alive by option interval ...

  • Page 810

    Issue 4.0 2-770 program 84 : hardware setup for voip description use program 84-15 : h.323/sip phone keep alive setup to set the keep alive configuration of the h.323/sip phone. Conditions none feature cross reference none program 84 : hardware setup for voip 84-15 : h.323/sip phone keep alive setup...

  • Page 811

    Issue 4.0 sv9100 programming manual 2-771 description use program 84-16 : voip limiter control gain to set the limiter control gain configuration of voip. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-16 : voip limiter control gai...

  • Page 812

    Issue 4.0 2-772 program 84 : hardware setup for voip description use program 84-19 : sip extension codec information basic setup to define the codec information for the sip extensions. Program 84 : hardware setup for voip 84-19 : sip extension codec information basic setup level: in input data item ...

  • Page 813

    Issue 4.0 sv9100 programming manual 2-773 17 jitter buffer mode 1 = static 3 = self adjusting 3 18 vad threshold 0~30 (-19db~+10db) 0 = self adjustment 1 = -19db (-49dbm) : 20 = 0db (-30dbm) : 29 = 9db (-21dbm) 30 = 10db (-20dbm) 20 28 audio capability priority 0 = g.711_pt 2 = g.729_pt 3 = g.722 4 ...

  • Page 814

    Issue 4.0 2-774 program 84 : hardware setup for voip 65 video quality mode this program specifies the sip station video quality mode when peer-to peer is disabled in 15-05- 50. Use this program in conjunction with 84-27-20 for mode 1 and 84-27-21 for mode 2 video quality settings. Mode 1 = cif (352x...

  • Page 815

    Issue 4.0 sv9100 programming manual 2-775 conditions none feature cross reference none 70 maximum jitter buffer for video this program sets the maximum value of jitter buffer for the video stream. It is used only when 84-19-72 (jitter buffer mode for video) is set to 1: fixed. This value must be big...

  • Page 816

    Issue 4.0 2-776 program 84 : hardware setup for voip description use program 84-20 : sip extension basic information setup to set up proxy information, session timers, called party information and expire value of invite. Conditions these commands are for sip analog extensions. Feature cross referenc...

  • Page 817

    Issue 4.0 sv9100 programming manual 2-777 description use program 84-21 : ccis over ip codec information basic setup to set the codec parameters of the gpz-iple. Program 84 : hardware setup for voip 84-21 : ccis over ip codec information basic setup level: in input data item no. Item input data defa...

  • Page 818

    Issue 4.0 2-778 program 84 : hardware setup for voip 19 1st priority of audio capability 0 = g.711 pt 2 = g.729 pt 3 = g.722 4 = g.726 0 20 2nd priority of audio capability 0 = g.711 pt 2 = g.729 pt 3 = g.722 pt 4 = g.726 pt 2 22 jitter buffer mode 1 = static 3 = self adjusting 3 23 voice activity d...

  • Page 819

    Issue 4.0 sv9100 programming manual 2-779 conditions none feature cross reference voice over internet protocol (voip) 43 rtp filter to avoid incorrect voice pass connection, this program checks the sending side address from received rtp packet at voipdb. 0 = disable 1 = enable 1 input data (continue...

  • Page 820

    Issue 4.0 2-780 program 84 : hardware setup for voip description use program 84-22 : dt800/dt700 multiline logon information setup to set the dt700 multiline logon information. Program 84 : hardware setup for voip 84-22 : dt800/dt700 multiline logon information setup level: in input data personal id...

  • Page 821

    Issue 4.0 sv9100 programming manual 2-781 conditions none feature cross reference voice over internet protocol (voip) 05 nick name input the personal id from terminal automatically when log on again. Up to 32 characters no setting item no. Item input data default.

  • Page 822

    Issue 4.0 2-782 program 84 : hardware setup for voip description use program 84-23 : dt800/dt700 multiline basic information setup to set the basic information for the dt800/dt700 multiline terminal. Program 84 : hardware setup for voip 84-23 : dt800/dt700 multiline basic information setup level: in...

  • Page 823

    Issue 4.0 sv9100 programming manual 2-783 conditions none feature cross reference voice over internet protocol (voip) 08 digest authorization registration expire timer 0~4294967295 (sec) 0 09 temporary password (read only) 10 number of password retries input the number of times an incorrect password...

  • Page 824

    Issue 4.0 2-784 program 84 : hardware setup for voip description use program 84-24 : dt800/dt700 multiline codec basic information setup to set the codec of each type of dt800/dt700 multiline telephone. Program 84 : hardware setup for voip 84-24 : dt800/dt700 multiline codec basic information setup ...

  • Page 825

    Issue 4.0 sv9100 programming manual 2-785 09 g.729 jitter buffer (min) 0~300ms 20 10 g.729 jitter buffer (average) 0~300ms 40 11 g.729 jitter buffer (max) 0~300ms 80 17 jitter buffer mode 1 = static 3 = self adjusting 3 18 vad threshold 0~30 (-19db~+10db) 0 = self adjustment 1 = -19db (-49dbm) : 20 ...

  • Page 826

    Issue 4.0 2-786 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip).

  • Page 827

    Issue 4.0 sv9100 programming manual 2-787 description use program 84-25 : netlink codec information basic setup to set the codec with netlink. Program 84 : hardware setup for voip 84-25 : netlink codec information basic setup level: in input data item no. Item input data default 01 number of g.711 a...

  • Page 828

    Issue 4.0 2-788 program 84 : hardware setup for voip 18 voice activity detection threshold 0~30 (-19db~ +10db) 0 = self adjustment 1 = -19db (-49dbm) : 20 = 0db (-30dbm) : 29 = 9db (-21dbm) 30 = 10db (-20dbm) 20 28 audio capability priority 0~4 0 = g.711_pt 2 = g.729_pt 3 = g.722_pt 4 = g.726 0 33 n...

  • Page 829

    Issue 4.0 sv9100 programming manual 2-789 conditions none feature cross reference voice over internet protocol (voip).

  • Page 830: 84-26 : Ipl Basic Setup

    Issue 4.0 2-790 program 84 : hardware setup for voip description use program 84-26 : ipl basic setup to set the ip address of ipl and the port. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-26 : ipl basic setup level: in input dat...

  • Page 831: 84-27 : Ipl Basic Setup

    Issue 4.0 sv9100 programming manual 2-791 description use program 84-27 : ipl basic setup to set the dtmf relay and the srtp mode of the ipl. Program 84 : hardware setup for voip 84-27 : ipl basic setup level: in input data slot number 1 item no. Item input data default 03 srtp mode setup 0 = disabl...

  • Page 832

    Issue 4.0 2-792 program 84 : hardware setup for voip 20 maximum non-mcu video channel mode 1 note when changing this prg all dsp resources are reset when idle. In progress calls are not affected but until all dsp resources go idle this change will not take affect. Sets the number of voip dsp resourc...

  • Page 833

    Issue 4.0 sv9100 programming manual 2-793 conditions none feature cross reference voice over internet protocol (voip) 23 maximum mcu group number (mode 2) note when changing this prg all dsp resources are reset when idle. In progress calls are not affected but until all dsp resources go idle this ch...

  • Page 834

    Issue 4.0 2-794 program 84 : hardware setup for voip description use program 84-28 : dt800/dt700 multiline firmware name setup to set the firmware name to download for the ip phone. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-28...

  • Page 835

    Issue 4.0 sv9100 programming manual 2-795 description use program 84-29 : dt800/dt700 codec information fixed mode setup to set the codec data of the dt800/dt700 when it uses multicast. Conditions when using g.711, prg 84-29-02 only 10ms, 20ms, 30ms and 40ms are used. Feature cross reference none pr...

  • Page 836

    Issue 4.0 2-796 program 84 : hardware setup for voip description use program 84-30 : pva-ccis over ip codec setup to set the codec information of the pva- ccis over ip. Program 84 : hardware setup for voip 84-30 : pva-ccis over ip codec setup level: in input data item no. Item input data default 01 ...

  • Page 837

    Issue 4.0 sv9100 programming manual 2-797 17 tx gain 0~40 (-14dbm ~ +14dbm) 0 = -20dbm 1 = -19dbm : 20 = 0dbm : 39 = 19dbm 40 = 20dbm 20 18 rx gain 0~40 (-14dbm ~ +14dbm) 0 = -20dbm 1 = -19dbm : 20 = 0dbm : 39 = 19dbm 40 = 20dbm 20 19 1st priority of audio capability 0 = g.711_pt 1 = g.723_pt 2 = g....

  • Page 838

    Issue 4.0 2-798 program 84 : hardware setup for voip conditions pva-ccis codec changes require a reset of the gcd-pvaa blade. Feature cross reference none.

  • Page 839

    Issue 4.0 sv9100 programming manual 2-799 description use program 84-31 : voipdb echo canceler setup to set the iple blade parameters. Program 84 : hardware setup for voip 84-31 : voipdb echo canceler setup level: in input data type 1 = h.323 trunk 2 = networking 3 = sip trunk 4 = sip extension 5 = ...

  • Page 840

    Issue 4.0 2-800 program 84 : hardware setup for voip 06 tdm echo canceler tail length normally not used. Select length of echo. Effective when 84-31-01 = 1 1 = 32ms 2 = 48ms 3 = 64ms 4 = 80ms 5 = 96ms 6 = 112ms 7 = 128ms 7 07 tdm echo canceler default erle level normally not used. Select length of e...

  • Page 841

    Issue 4.0 sv9100 programming manual 2-801 13 tdm tx hlc threshold select hlc threshold level. Effective when 84-31-10 = 3 0~42 (-42 ~ 0) 0 = -42dbm 1 = -41dbm : 41 = -1dbm 42 = 0dbm 41 14 tdm tx gain compression mode transmit gain compression on or off. Effective when 84-31-10 = 3 0 = disable 1 = en...

  • Page 842

    Issue 4.0 2-802 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip) 37 tdm echo canceler nlp mode (4w) select echo compression mode for remaining echo. Effective when 84-31-19 = 1 0 = disable 1 = enable 1 input data (continued) item no. It...

  • Page 843: 84-33 : Fax Over Ip Setup

    Issue 4.0 sv9100 programming manual 2-803 description use program 84-33 : fax over ip setup to set up the parameters of the fax over ip function. Program 84 : hardware setup for voip 84-33 : fax over ip setup level: in input data type 1 = h.323 trunk 2 = networking 3 = sip trunk 4 = sip extension 5 ...

  • Page 844

    Issue 4.0 2-804 program 84 : hardware setup for voip conditions none feature cross reference voice over internet protocol (voip) 11 t.38 ecm (error correction mode) 0 = disable 1 = enable 1 12 fax codec 1 = g.711 a-law 2 = g.711 u-law 3 = g.726 2 13 payload size 1 ~ 4 (10ms base) 2 14 jitter buffer ...

  • Page 845: 84-34 : Voipdb Dtmf Setup

    Issue 4.0 sv9100 programming manual 2-805 description use program 84-34 : voipdb dtmf setup to set up the basic parameters of the dtmf. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-34 : voipdb dtmf setup level: in input data type...

  • Page 846

    Issue 4.0 2-806 program 84 : hardware setup for voip description use program 84-35 : voipdb rfc2833 playout setup to set up the parameters of the dtmf playout of rfc2833 packet reception from the network. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardwa...

  • Page 847

    Issue 4.0 sv9100 programming manual 2-807 description use program 84-36 : voipdb dtmf transmit setup to set up the dtmf transmit parameters. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-36 : voipdb dtmf transmit setup level: in i...

  • Page 848

    Issue 4.0 2-808 program 84 : hardware setup for voip description use program 84-37 : voipdb dtmf transmit setup to set up the dtmf detection parameters. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-37 : voipdb dtmf detection setu...

  • Page 849

    Issue 4.0 sv9100 programming manual 2-809 description use program 84-38 : voipdb network side echo canceler setup to set up the echo canceller parameters. Program 84 : hardware setup for voip 84-38 : voipdb network side echo canceler setup level: in input data type 1 = h.323 trunk 2 = networking 3 =...

  • Page 850

    Issue 4.0 2-810 program 84 : hardware setup for voip 07 echo canceler default erl level 0 ~ 6 (-9db ~ 9db) 0 = -9db 1 = -6db 2 = -3db : 5 = 6db 6 = 9db 5 08 echo canceler echo type 1 = line e. C. 2 = acoustic e.C. 1 09 --- not used --- 10 tx level control 0 = disable 1 = manual 2 = auto 3 = hlc 0 11...

  • Page 851

    Issue 4.0 sv9100 programming manual 2-811 conditions none feature cross reference voice over internet protocol (voip) 16 rx level control 0 = disable 1 = enable 2 = auto 0 17 rx level control level 0 ~ 16 (-24db ~ 24db) 0 = -24db 1 = -21db 2 = -18db : 8 = 0db : 14 = 18db 15 = 21db 16 = 24db 8 18 rx ...

  • Page 852

    Issue 4.0 2-812 program 84 : hardware setup for voip description use program 84-39 : sip trunk message customization to observe sip trunk information. This program is read only. Conditions none feature cross reference voice over internet protocol (voip) program 84 : hardware setup for voip 84-39 : s...

  • Page 853: 90-01 : Installation Date

    Sv9100 programming manual 2-813 program: 90 description use program 90-01 : installation date to define the installation date of the system. Conditions none feature cross reference none program 90 : maintenance program 90-01 : installation date level: in input data item no. Item input data default 0...

  • Page 854

    Issue 4.0 2-814 program 90 : maintenance program description use program 90-02 : programming password setup to set the system passwords. For password entry, the system allows eight users to be defined. Each user can have a: unique alphanumeric name (up to 10 alphanumeric characters) password entry o...

  • Page 855

    Issue 4.0 sv9100 programming manual 2-815 default conditions more than one extension can be in the programming mode. Feature cross reference none user no. User name password level level description 1 necii 47544 1 (mf) manufacturer level - access to all system programs. 2 tech 12345678 2 (in) instal...

  • Page 856: 90-03 : Save Data

    Issue 4.0 2-816 program 90 : maintenance program description use program 90-03 : save data to save the programmed data on the usb flash drive. This program should be used after changing the programmed data. Conditions when reloading a customer database, the system must be reset (either using program...

  • Page 857: 90-04 : Load Data

    Issue 4.0 sv9100 programming manual 2-817 description use program 90-04 : load data to load the system data from the inserted usb flash drive to the sram and flash rom in the system. Conditions after uploading the programming, reset the system and wait a few minutes for the system to reset completel...

  • Page 858: 90-05 : Slot Control

    Issue 4.0 2-818 program 90 : maintenance program description use program 90-05 : slot control to reset or delete (uninstall) blades (slots 1~24). Delete allows you to completely uninstall the blade. You should do this if you want to remove a blade and plug it into a different slot and still retain t...

  • Page 859

    Issue 4.0 sv9100 programming manual 2-819 feature cross reference none.

  • Page 860: 90-06 : Trunk Control

    Issue 4.0 2-820 program 90 : maintenance program description use program 90-06 : trunk control for trunk maintenance. Busy out lets you block a blade from placing outgoing calls (just like placing the blade switch down). Once busied out, none of the ports on the blade can be used for new calls. Exis...

  • Page 861: 90-07 : Station Control

    Issue 4.0 sv9100 programming manual 2-821 description use program 90-07 : station control for extension maintenance. Conditions none feature cross reference none program 90 : maintenance program 90-07 : station control level: sa note this program is available only via telephone programming and not t...

  • Page 862: 90-08 : System Reset

    Issue 4.0 2-822 program 90 : maintenance program description use program 90-08 : system reset to perform a system reset. Conditions after restoring a customer database, the system must be reset using program 90-08 or by powering down/ powering up before all the restored programming takes affect. Fea...

  • Page 863

    Issue 4.0 sv9100 programming manual 2-823 description use program 90-09 : automatic system reset time setup to define the time for the system to automatically reset. Conditions none feature cross reference none program 90 : maintenance program 90-09 : automatic system reset time setup level: in inpu...

  • Page 864: 90-10 : System Alarm Setup

    Issue 4.0 2-824 program 90 : maintenance program description use program 90-10 : system alarm setup to assign a status to system alarms. You can designate an alarm as major or minor. This program also assigns whether or not the alarm information is reported to the predefined destination. Program 90 ...

  • Page 865

    Issue 4.0 sv9100 programming manual 2-825 3 2 0 connection fault between gcd-cp10 and other pkgs. The error occurred when communicating with the package. When the package is broken, it recognizes it as a communication fault. 1. The unit is not completely installed. 2. The power- supply voltage of th...

  • Page 866

    Issue 4.0 2-826 program 90 : maintenance program 6 0 0 blocking the link of terminals connected with the esi package came off. 1. Terminal breakdown. 2 faulty wiring and wiring termination. 3. External noise. 4. Esi package breakdown. 1. Confirm the terminal connected with same esi. If they work nor...

  • Page 867

    Issue 4.0 sv9100 programming manual 2-827 12 0 0 mis link error the link with mis client pc came off. 1. Lan cable defective. 2. Connected hub broken. 3. The cti server doesn't start normally. 1. Confirm mis client pc and connected part. 2. Check with manufacturer if the problem occurs again. When t...

  • Page 868

    Issue 4.0 2-828 program 90 : maintenance program 29 0 0 charge management buffer full the temporary buffer for the charge management in main device overflowed, and a part of unoutput charge data disappeared because it could not output the charge management data. 1. The charge data is printed and not...

  • Page 869

    Issue 4.0 sv9100 programming manual 2-829 36 0 0 cs error notification 1 cs detected the problem occurring in the air synchronous signal between cs-csiu, bbic reset was executed, and it was restored automatically. 1. Outgoing noise. 2. Method of setting up cs. 3. Wiring to connect csiu unit with cs....

  • Page 870

    Issue 4.0 2-830 program 90 : maintenance program 40 0 0 cs error noti- fication 2. Cs detected the factor that the noise is generated between cs-ps, bbic reset was executed, and it was restored automatically. 1. Outgoing noise. 2. Method of setting up cs. 3. Wiring to connect csiu unit with cs. 4. H...

  • Page 871

    Issue 4.0 sv9100 programming manual 2-831 57 2 0 ip collision error collision(01) indicates the address programmed in 10-12-01 has been duplicated. Collision (02) indicates the address programmed in 10-12-09 has been duplicated. Collision(03) ~ collision(10) indicates the addresses programmed in 84-...

  • Page 872

    Issue 4.0 2-832 program 90 : maintenance program 61 0 0 sip extension trouble information. 1. Failed registration of the sip extension terminal. 2. The sip extension terminal dsp was not acquired: • at registration of sip extension terminal to sv9100. • when you cannot acquire the dsp resource when ...

  • Page 873

    Issue 4.0 sv9100 programming manual 2-833 70 2 0 sip stack reconfig report 71 2 0 cid buffer threshold when the number of cid records is over the limit, cid buffer threshold alarm (71) can be reported. 72~73 --- reserved --- 74 2 0 tls sip error information 1. License is insufficient 2. Error in ca ...

  • Page 874

    Issue 4.0 2-834 program 90 : maintenance program 82 2 0 netlink virtual slot accommod. Error. The trouble occurred with virtual slot relation. • it exceeded the upper slot accommodation. • it failed to make a virtual slot. Exceeds slot accommodations in the netlink system. 1. Confirm upper slot numb...

  • Page 875

    Issue 4.0 sv9100 programming manual 2-835 conditions the entire terminal that has an alarm display setting can be set at prg90-50-01. System alarm type is shown despite the setting done at 90-10-01. If multiple alarm display setting is set, only one highest priority alarm will be shown on a lcd disp...

  • Page 876

    Issue 4.0 2-836 program 90 : maintenance program feature cross reference none.

  • Page 877: 90-11 : System Alarm Report

    Issue 4.0 sv9100 programming manual 2-837 description use program 90-11 : system alarm report to define the details of the system alarm report. Program 90 : maintenance program 90-11 : system alarm report level: in input data item no. Item input data default 02 report method when alarm reports are e...

  • Page 878

    Issue 4.0 2-838 program 90 : maintenance program conditions none feature cross reference none 13 customer name when alarm reports are e-mailed, enter a name to identify the particular system. Up to 255 characters no setting 14 change smtp client when enabled the system uses the programs in 47-18-xx ...

  • Page 879: 90-12 : System Alarm Output

    Issue 4.0 sv9100 programming manual 2-839 description use program 90-12 : system alarm output to set the options for the alarm report. Define the output port to be used as the output for system alarm report and set the system alarm options. The system can have up to 50 reports. Conditions none featu...

  • Page 880

    Issue 4.0 2-840 program 90 : maintenance program description use program 90-13 : system information output to define the output port to be used as the system information output. Conditions none feature cross reference none program 90 : maintenance program 90-13 : system information output level: in ...

  • Page 881

    Issue 4.0 sv9100 programming manual 2-841 description use program 90-16 : main software information to display the main software information on the gcd-cp10. Main software information can also be viewed outside of system programming by pressing feature and the 3 key on any multiline terminal. Condit...

  • Page 882: 90-17 : Firmware Information

    Issue 4.0 2-842 program 90 : maintenance program description use program 90-17 : firmware information to display the firmware versions of the various system blades. Conditions none feature cross reference none program 90 : maintenance program 90-17 : firmware information level: in input data item no...

  • Page 883: 90-19 : Dial Block Release

    Issue 4.0 sv9100 programming manual 2-843 description when the extension number is entered in program 90-19 : dial block release, the extension is released from the dial block restriction. Conditions none feature cross reference code restriction program 90 : maintenance program 90-19 : dial block re...

  • Page 884

    Issue 4.0 2-844 program 90 : maintenance program description use program 90-20 : traffic report data setup to define the details of the traffic report. Program 90 : maintenance program 90-20 : traffic report data setup level: in input data item no. Item input data default 01 call traffic output 0 = ...

  • Page 885

    Issue 4.0 sv9100 programming manual 2-845 conditions none feature cross reference traffic reports 11 security sensor dial record 0 = not recorded 1 = recorded 0 input data (continued) item no. Item input data default.

  • Page 886

    Issue 4.0 2-846 program 90 : maintenance program description use program 90-21 : traffic report output to define the output port to be used as the traffic report output. Conditions none feature cross reference traffic reports program 90 : maintenance program 90-21 : traffic report output level: in i...

  • Page 887

    Issue 4.0 sv9100 programming manual 2-847 description use program 90-23 : deleting registration of ip telephones to delete the registered ip telephone from the system. Conditions none feature cross reference voice over internet protocol (voip) program 90 : maintenance program 90-23 : deleting regist...

  • Page 888

    Issue 4.0 2-848 program 90 : maintenance program description use program 90-24 : system alarm report notification time setup to set the date and time for the alarm report to print. Conditions none feature cross reference none program 90 : maintenance program 90-24 : system alarm report notification ...

  • Page 889

    Issue 4.0 sv9100 programming manual 2-849 description use program 90-25 : system alarm report cc mail setup to define the mail address to receive the system alarm report cc mail setup. Conditions none feature cross reference none program 90 : maintenance program 90-25 : system alarm report cc mail s...

  • Page 890

    Issue 4.0 2-850 program 90 : maintenance program description use program 90-26 : program access level setup to define the password access level required to change a system program. Conditions none feature cross reference none program 90 : maintenance program 90-26 : program access level setup level:...

  • Page 891

    Issue 4.0 sv9100 programming manual 2-851 description use program 90-28 : user programming password setup to set the password used to enter the user programming mode. Conditions none feature cross reference none program 90 : maintenance program 90-28 : user programming password setup level: in input...

  • Page 892

    Issue 4.0 2-852 program 90 : maintenance program description use program 90-31 : dim access over ethernet to enable dim (diagnostic information maintenance) access over the lan, and to define the user name and password. Dim is a maintenance tool used by engineering to extract trace level information...

  • Page 893: 90-34 : Firmware Information

    Issue 4.0 sv9100 programming manual 2-853 description use program 90-34 : firmware information to list the package type and firmware blades installed in the system. Conditions these programs are read only. Feature cross reference none program 90 : maintenance program 90-34 : firmware information lev...

  • Page 894

    Issue 4.0 2-854 program 90 : maintenance program description use program 90-35 : wizard programming level setup to set the maintenance level for wizard programming. Conditions none feature cross reference none program 90 : maintenance program 90-35 : wizard programming level setup level: in note thi...

  • Page 895

    Issue 4.0 sv9100 programming manual 2-855 description use program 90-36 : firmware update time setting to show the data for the firmware update feature. The following firmware is available to update with this feature: main.Bin dspdbu.Bin dsp.Bin program 90 : maintenance program 90-36 : firmware upda...

  • Page 896

    Issue 4.0 2-856 program 90 : maintenance program conditions these programs are read only. Feature cross reference none sample report result report display update success update is successful with the update time. Update fail update failed. Drive a (compact flash) was not available. Update fail updat...

  • Page 897

    Issue 4.0 sv9100 programming manual 2-857 description use program 90-37 : set temporary license to set the effective days of the temporary license. Conditions switch reset is required for changes to take effect. Feature cross reference none program 90 : maintenance program 90-37 : set temporary lice...

  • Page 898

    Issue 4.0 2-858 program 90 : maintenance program description use program 90-38 : user programming data level setup sets system data to turn on/off each user programming feature program 90 : maintenance program 90-38 : user programming data level setup level: in input data item no. Item input data de...

  • Page 899

    Issue 4.0 sv9100 programming manual 2-859 13 dss key assignment 0 = off 1 = on 1 14 doorphone ringing assignment 0 = off 1 = on 1 15 extension numbering 0 = off 1 = on 1 16 extension name 0 = off 1 = on 1 17 night-mode switching own group 0 = off 1 = on 1 18 call forward-immediate/no answer/both rin...

  • Page 900

    Issue 4.0 2-860 program 90 : maintenance program conditions switch reset is required for changes to take effect. Feature cross reference none 30 spd area no. (prg 24-04) 0 = off 1 = on 1 31 telephone data copy 0 = off 1 = on 1 32 dial in name (prg 22-11-03) 0 = off 1 = on 1 33 lcd line key name assi...

  • Page 901

    Issue 4.0 sv9100 programming manual 2-861 description use program 90-39 : virtual loop back port reset to reset to initial status. Conditions none feature cross reference none program 90 : maintenance program 90-39 : virtual loop back port reset level: in note this program is available only via tele...

  • Page 902

    Issue 4.0 2-862 program 90 : maintenance program description use program 90-41 : server setting to update terminal local data to define the primary dns server address, the secondary dns server address and the data roaming server address. Conditions none feature cross reference none program 90 : main...

  • Page 903

    Issue 4.0 sv9100 programming manual 2-863 description use program 90-42 : dt800/dt700 multiline terminal version information to set the hardware version and firmware version of the dt800/dt700 mlt terminal. Conditions none feature cross reference none program 90 : maintenance program 90-42 : dt800/d...

  • Page 904

    Issue 4.0 2-864 program 90 : maintenance program description use program 90-43 : deleting terminal license of dt800/dt700 to delete the terminal license information delivered to the dt800/dt700 terminal. Conditions none feature cross reference none program 90 : maintenance program 90-43 : deleting t...

  • Page 905

    Issue 4.0 sv9100 programming manual 2-865 description use program 90-44 : deleting terminal license of tcp interface to delete the terminal license information delivered to the terminal with a tcp interface. Conditions none feature cross reference none program 90 : maintenance program 90-44 : deleti...

  • Page 906

    Issue 4.0 2-866 program 90 : maintenance program description use program 90-45 : temporary password change for dt800/dt700 to change the temporary password that is set in the encryption function. Conditions none feature cross reference none program 90 : maintenance program 90-45 : temporary password...

  • Page 907

    Issue 4.0 sv9100 programming manual 2-867 description use program 90-48 : button kit information of multiline telephone to set the button kit information on a new telephone on the sv9100 system. Conditions none feature cross reference none program 90 : maintenance program 90-48 : button kit informat...

  • Page 908

    Issue 4.0 2-868 program 90 : maintenance program description use program 90-49 : protection mode setup for multiline telephone to set the protection mode of each multiline (ip) telephone. Conditions none feature cross reference none program 90 : maintenance program 90-49 : protection mode setup for ...

  • Page 909

    Issue 4.0 sv9100 programming manual 2-869 description use program 90-50 : system alarm display setup to set the system alarm report display. Conditions none feature cross reference none program 90 : maintenance program 90-50 : system alarm display setup level: in input data index number 01~50 item n...

  • Page 910

    Issue 4.0 2-870 program 90 : maintenance program description use program 90-51 : alarm setup for maintenance exchange to set the day for the maintenance exchange of parts that need regular maintenance. Program 90 : maintenance program 90-51 : alarm setup for maintenance exchange level: in input data...

  • Page 911

    Issue 4.0 sv9100 programming manual 2-871 conditions none feature cross reference none.

  • Page 912: 90-52 : System Alarm Save

    Issue 4.0 2-872 program 90 : maintenance program description use program 90-52 : system alarm save for the system alarm output operation. Conditions none feature cross reference none program 90 : maintenance program 90-52 : system alarm save level: in note this program is available only via telephon...

  • Page 913: 90-53 : System Alarm Clear

    Issue 4.0 sv9100 programming manual 2-873 description use program 90-53 : system alarm clear to clear the system alarm. Conditions none feature cross reference none program 90 : maintenance program 90-53 : system alarm clear level: in note this program is available only via telephone programming and...

  • Page 914: 90-54 : Pc/web Programming

    Issue 4.0 2-874 program 90 : maintenance program description use program 90-54 : pc/web programming sets parameters for pc and web programming. Conditions none feature cross reference none program 90 : maintenance program 90-54 : pc/web programming level: in input data item no. Item input data defau...

  • Page 915: 90-55 : Free License Select

    Issue 4.0 sv9100 programming manual 2-875 description use program 90-55 : free license select to validate the free license. Conditions none feature cross reference none program 90 : maintenance program 90-55 : free license select level: in input data item no. Item input data default 01 start free li...

  • Page 916: 90-56 : Ntp Setup

    Issue 4.0 2-876 program 90 : maintenance program description use program 90-56 : ntp setup to set the ntp. Conditions none feature cross reference none program 90 : maintenance program 90-56 : ntp setup level: in item no. Item input data default 01 ntp synchronize 0 = no 1 = yes 0 02 server address ...

  • Page 917: 90-57 : Backup Recovery Data

    Issue 4.0 sv9100 programming manual 2-877 description use program 90-57 : backup recovery data to backup the system data in the flash memory on the gcd-cp10 and to make the recovery data. Conditions none feature cross reference none program 90 : maintenance program 90-57 : backup recovery data level...

  • Page 918

    Issue 4.0 2-878 program 90 : maintenance program description use program 90-58 : restore recovery data to select the recovery data stored in the flash memory of the gcd-cp10. After this command is executed, the system restarts automatically. Conditions none feature cross reference none program 90 : ...

  • Page 919: 90-59 : Delete Recovery Data

    Issue 4.0 sv9100 programming manual 2-879 description use program 90-59 : delete recovery data to select and delete the recovery data stored in the flash memory of the gcd-cp10. Conditions none feature cross reference none program 90 : maintenance program 90-59 : delete recovery data level: sa note ...

  • Page 920

    Issue 4.0 2-880 program 90 : maintenance program description use program 90-60 : t1/isdn layer status information to display layer status information for t1/pri/ bri/cd-ccta packages. Conditions this program is read-only. Feature cross reference none program 90 : maintenance program 90-60 : t1/isdn ...

  • Page 921: 90-61 : Manual Slot Install

    Issue 4.0 sv9100 programming manual 2-881 description use program 90-61 : manual slot install to manually install any package. If another package is already assigned, the new package cannot be assigned. Conditions none feature cross reference none program 90 : maintenance program 90-61 : manual slot...

  • Page 922

    Issue 4.0 2-882 program 90 : maintenance program description use program 90-62 : security id information to display the security id of the gcd-cp10. Conditions none feature cross reference none program 90 : maintenance program 90-62 : security id information level: in note this program is available ...

  • Page 923: 90-63 : Dt800/dt700 Control

    Issue 4.0 sv9100 programming manual 2-883 description use program 90-63 : dt800/dt700 control to adjust settings of the dt700 and dt800. Conditions none feature cross reference none program 90 : maintenance program 90-63 : dt800/dt700 control level: in input data item no. Item input data default 01 ...

  • Page 924: 90-64 : Snmp Setup

    Issue 4.0 2-884 program 90 : maintenance program description use program 90-64 : snmp setup to configure the snmp function. Conditions none feature cross reference none program 90 : maintenance program 90-64 : snmp setup level: in input data item no. Item input data default 01 snmp 0 = disable 1 = e...

  • Page 925

    Issue 4.0 sv9100 programming manual 2-885 description use program 90-65 : 1st party cti authentication password setup to set the authentication password. Conditions none feature cross reference none program 90 : maintenance program 90-65 : 1st party cti authentication password setup level: in input ...

  • Page 926

    Issue 4.0 2-886 program 90 : maintenance program description use program 90-68 : side tone auto setup to automatically adjust the analog trunk codec filter settings. Conditions none feature cross reference none program 90 : maintenance program 90-68 : side tone auto setup level: in note this program...

  • Page 927

    Issue 4.0 sv9100 programming manual 2-887 description use program 90-69 : outbound ip connection setup to set the outbound ip connection information. Conditions none feature cross reference none program 90 : maintenance program 90-69 : outbound ip connection setup level: in input data item no. Item ...

  • Page 928: 90-73 : Line Load Control

    Issue 4.0 2-888 program 90 : maintenance program description use program 90-73 : line load control to set the line load control settings. Conditions none feature cross reference none program 90 : maintenance program 90-73 : line load control level: in input data item no. Item input data default 01 l...

  • Page 929

    Issue 4.0 sv9100 programming manual 2-889 description use program 90-77 : lan link speed information to provide information about the lan link speed & duplex mode. Conditions none feature cross reference none program 90 : maintenance program 90-77 : lan link speed information level: in input data it...

  • Page 930

    Issue 4.0 2-890 program 90 : maintenance program.

  • Page 931: Program 92 : Copy Program

    Sv9100 programming manual 2-891 program: 92 description use program 92-01 : copy program to copy the data for one program to another multiline terminal, port, group, or other number. Refer to the following charts to see which programs can be copied. . Program 92 : copy program 92-01 : copy program l...

  • Page 932

    Issue 4.0 2-892 program 92 : copy program the copy program is applicable only for the following programs: trunk port base trunk group base extension base program no. Program name note 14-01 trunk basic data setup copy all data except trunk name (item 01). 14-02 analog trunk data setup 14-04 behind p...

  • Page 933

    Issue 4.0 sv9100 programming manual 2-893 department group base 15-03 single line telephone basic data setup 15-06 trunk access map for extension 15-07 programmable function key 15-08 incoming virtual extension ring tone setup 15-09 virtual extension ring assignment 15-10 incoming virtual extension ...

  • Page 934

    Issue 4.0 2-894 program 92 : copy program dss console base door box base conditions using this program to copy a multiline terminal programmable function keys, copies all keys whether or not they exist on the terminal to which the programming is being copied. This may cause confusion when trying to ...

  • Page 935: Program 92 : Copy Program

    Issue 4.0 sv9100 programming manual 2-895 description use program 92-02 : delete all extension numbers to delete all extension numbers. However, the extension number of the first port is not deleted. Conditions none feature cross reference none program 92 : copy program 92-02 : delete all extension ...

  • Page 936: Program 92 : Copy Program

    Issue 4.0 2-896 program 92 : copy program description use program 92-03 : copy program by port number to copy extension and the data of each outside line. Conditions none feature cross reference none program 92 : copy program 92-03 : copy program by port number level: in note this program is availab...

  • Page 937: Program 92 : Copy Program

    Issue 4.0 sv9100 programming manual 2-897 description use program 92-04 : extension data swap to swap data between two extensions. The following table lists programs that use the extension data swap function. Program 92 : copy program 92-04 : extension data swap level: in note this program is availa...

  • Page 938

    Issue 4.0 2-898 program 92 : copy program 15-11 virtual extension delayed ring assignment 15-12 conversation recording destination for extension 15-13 loop key data 15-14 programming one-touch keys 15-17 co-message waiting indication 15-18 virtual extension key enhance options 15-19 system telephone...

  • Page 939

    Issue 4.0 sv9100 programming manual 2-899 conditions none feature cross reference none 24-07 fixed call forward off-premise 24-08 call forward for centrex 24-09 call forward split settings 26-04 ars class of service 26-07 lcr cost center code table 31-02 internal paging group assignment 41-02 agent ...

  • Page 940: Program 92 : Copy Program

    Issue 4.0 2-900 program 92 : copy program description use program 92-05 : extension data swap password to define the 4-digit password for each extension to allow extension data swap. Conditions none feature cross reference none program 92 : copy program 92-05 : extension data swap password level: in...

  • Page 941: Program 92 : Copy Program

    Issue 4.0 sv9100 programming manual 2-901 description use program 92-06 : fill command to allocate the data of each extension number of each extension group or each table. . The following table lists programs that use the fill command function. Program 92 : copy program 92-06 : fill command level: i...

  • Page 942

    Issue 4.0 2-902 program 92 : copy program conditions none feature cross reference none.

  • Page 943: Program 92 : Copy Program

    Issue 4.0 sv9100 programming manual 2-903 description use program 92-07 : delete command to delete the data of each extension number of each extension group or each table. . The following table lists programs that use the delete command function. Program 92 : copy program 92-07 : delete command leve...

  • Page 944

    Issue 4.0 2-904 program 92 : copy program conditions none feature cross reference none.

  • Page 945

    Sv9100 programming manual 3-905 program: 93 description use program 93-01 : day/night mode information to display day/night mode for night mode service group. Conditions none feature cross reference none program 93: system information 93-01 : day/night mode information level: in input data night mod...

  • Page 946: 93-02 : Trunk Information

    Issue 4.0 3-906 program 93: system information description use program 93-02 : trunk information to display the setting of each trunk. Conditions none feature cross reference none program 93: system information 93-02 : trunk information level: in input data trunk no. 001~400 input data item no. Item...

  • Page 947

    Issue 4.0 sv9100 programming manual 3-907 description use program 93-03 : extension information todisplay the settings of each extension. Program 93: system information 93-03 : extension information level: in input data extension 1~960 input data item no. Item input data default related program 01 c...

  • Page 948

    Issue 4.0 3-908 program 93: system information 05 call forwarding – follow-me read only. Indicates call forward- follow-me setting status per extension. 0:disable 1:enable none 11-11-07 06 call forwarding follow- me destination. Read only. Indicates call forwarding follow-me extension number set per...

  • Page 949

    Issue 4.0 sv9100 programming manual 3-909 conditions none feature cross reference none 14 forced intercom ring (icm call type) read only. Indicates icm call type per extension. 0 = disable(voice) 1 = enable(signal) none 11-11-15 11-11-16 15 bgm read only. Indicates bgm setting status per extension. ...

  • Page 950: 93-04 : Redial List

    Issue 4.0 3-910 program 93: system information description use program 93-04 : redial list to display the redial list of each extension. Conditions none feature cross reference none program 93: system information 93-04 : redial list level: in input data extension 1~960 input data item no. Item input...

  • Page 951

    Issue 4.0 sv9100 programming manual 3-911 description use program 93-05 : department group information to display the settings of each department group. Conditions none feature cross reference none program 93: system information 93-05 : department group information level: in input data department gr...

  • Page 952

    Issue 4.0 3-912 program 93: system information description use program 93-06 : ip address for 1st party cti connection to display the settings of each department group. Conditions none feature cross reference none program 93: system information 93-06 : ip address list for 1st party cti connection le...

  • Page 954

    Programming manual nec corporation of america issue 4.0 sv 9100 ®.