141014-20 neo 2.5 insert-a 5055.950 installation and operating instructions model: neo 2.5 insert series: a safety notice if this stove is not properly installed, a house fi re may result. For your safety, follow the installation instructions. Contact local building or fi re officials about restrict...
2 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Contents safety ............................................................................................ 3 dimensions ............................................................................................ 3 clearances ......
141014-20 neo 2.5 insert-a 3 ©pacific energy fireplace products ltd. 16” 406mm 16”(406mm) 11 1/2 ” 292mm 15” 381mm 2” 51mm 8” 203mm clearances masonry or factory built fireplace the minimum required clearances to surrounding combustible materials when installed into a masonry or factory built fi rep...
4 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. 16” 406mm non-combustible fi replace hearth 34” 864mm 22” 559mm 8” 203mm fireplace hearth requirements: (measured without the insert) the hearth must be raised 2”(51mm) above an adjacent combustible fl oor and must extend 16”(406mm...
141014-20 neo 2.5 insert-a 5 ©pacific energy fireplace products ltd. Creosote formation and need for removal when wood is burned slowly, it produces tar and other or- ganic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney fl...
6 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Operation caution: never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fl uid or similar liquids to start or “freshen up” a fi re in this heater. Keep all such liquids well away from the heater while it is in...
141014-20 neo 2.5 insert-a 7 ©pacific energy fireplace products ltd. Restarting after extended or overnight burns 1) open door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of embers, close door. 2) adjust air control to “high” position(all the way to th...
8 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Warning: do not overtighten, tighten screws very carefully. - do not clean glass when hot - do not use abrasive cleaners on glass 6. Do not store wood within heater installation clearances, or within the space required for fuel loa...
141014-20 neo 2.5 insert-a 9 ©pacific energy fireplace products ltd. Blower replacement 1. Remove the surround front and back. Set them aside carefully to avoid damage. 2. Remove the surround mounting bracket by removing the two screws securing the bracket to the side casing of the unit. Fig. #2 3. ...
10 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Power cord position the power cord for the neo 2.5 insert comes factory set to exit the right side of the unit. If you desire, the cord can be switched to exit to the left of the unit. The cord will lose approximately 12”(305mm) o...
141014-20 neo 2.5 insert-a 11 ©pacific energy fireplace products ltd. Maintenance checks check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (see website for descriptions and more detail) weekly: - firebrick - visual, for cracking. - d...
12 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Installation your insert is designed to be installed into a masonry or fac- tory built zero-clearance fi replace. The masonry fi replace must be built according to the requirements of the standard of chimneys, fireplaces, vents an...
141014-20 neo 2.5 insert-a 13 ©pacific energy fireplace products ltd. 5) measure, trim and shape a top fl ashing to fi t the existing chimney fl ue. Plan for a 1”(25mm) to 1-1/2”(38mm) overlap on each side. Place fl ashing over top of the liner and seat fi rmly against the tile. 6) screw fl ashing c...
14 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Surround assembly and installation 1) attach the surround back to the surround mounting brackets on the unit with the four screws provided.Fig. #10 2) push the entire appliance back until the surround assembly is in contact with t...
141014-20 neo 2.5 insert-a 15 ©pacific energy fireplace products ltd. Blowers the insert comes equipped with variable speed circulating air blowers. The blower system is thermostatically controlled for automatic operation, as well manually with a convenient bypass switch. Blowers operation automatic...
16 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. Troubleshooting problem cause cure excessive creosote 1) wood is too wet - use dry wood(recommended moisture level buildup 2) turning down air control - do not turn down until: too soon a) there is a good bed of coals b) the wood ...
141014-20 neo 2.5 insert-a 17 ©pacific energy fireplace products ltd. Neo 2.5 insert firebrick installation instructions a b b c d item/ article dimensions part number/ numÉro de piÈce a 9” x 4 1/2” x 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 b 4 1/2” x 4 1/2” x 1 1/4” (115 mm x 115 mm x 32 mm) 7847 ...
18 neo 2.5 insert-a 141014-20 ©pacific energy fireplace products ltd. 1......Top casing ...................................................................... 7863.5 2......Side casing, lhs .............................................................. 7861 3......Side casing, rhs .....................
141014-20 neo 2.5 insert-a 19 ©pacific energy fireplace products ltd. Label minimum clearance to combustibles/dÉgagement minimum aux combustibles (measured from insert door opening) a) adjacent sidewall/ 419 mm / 16.5 in(po) paroi latÉrale adjacente b) side facing/ 330 mm / 13 in(po) revÊtement latÉ...
©pacific energy fireplace products ltd. Pacific energy fireplace products ltd. Phone: 1-250-748-1184 web site: http://www.Pacifi cenergy.Net 2975 allenby rd., duncan, b.C. V9l 6v8 pacific energy fireplace products ltd. Phone: 1-250-748-1184 web site: http://www.Pacifi cenergy.Net 2975 allenby rd., d...
