Tascam DM-3200 Release Notes - Dm-3200 Release Notes

DM-3200 Release Notes

12 

TASCAM  DM-3200 Release Notes

ª

MIDI mixer

You can send MIDI Control Change messages to exter-

nal MIDI devices using the 

POD

 knobs, 

FADER

 and the 

MUTE

 key of the DM-3200. In the default setting, they 

control 

PAN

, 

FADER

, and 

MUTE

 respectively.

Figure 10: MIDI MIXER screen

This operation is possible only when the Layer Status is set 

to 

REMOTE

 and the 

MIDI MIXER

 screen is currently show-

ing or was the last 

EXT.CTRL

 screen displayed. The screen 

will show “

REM PAN

” for the encoder mode, and the encod-

ers will control the pan data.

When ON/OFF status is set to ON, a check mark appears 

in the check box. When it is OFF, the box is blank. In the 

figure 11, all the channels are set to ON.

You cannot operate the MIDI control of the channel pan 

when the surround mode is not set to STEREO.

NOTE

When the Layer Status is set to 

REMOTE

 the pan value 

is displayed on, and can be controlled with the rotary 

encoders.

Changing the assignment

You can change the MIDI channel, Control Change 

number, and ON/OFF status that are assigned to each of 

the 

POD

 knobs, 

FADER

, and the 

MUTE

 key. Changes are 

made on the 

MIDI>CTRL.CHANGE

 screen.

Figure 11: MIDI>CTRL.CHANGE screen

To display this screen, either press the 

MIDI

 key followed 

by the 

POD 3

 key (or keep pressing the 

MIDI

 key), or move 

the cursor to the 

 (

Jump to SCREEN

) button at the top 

right on the 

MIDI MIXER

 screen, and press the 

ENTER

 key.

Use the 

POD 4

 knob to select the key whose assigned func-

tion is to be changed (

FADER

, 

PAN

 or 

MUTE

) in the 

TARGET

section on the right of the screen.

You will see a chart showing MIDI channel, Control 

Change number, and ON/OFF status of the selected key 

(channel 1-16) on the left of the screen.

Use the 

cursor

 key to select the item to be set, select the 

value using the 

JOG/DATA

 dial, then press the 

ENTER

key to set the value. When you are changing the ON/OFF 

status, press the 

ENTER

 key.

NOTE

If there is more than one key that is assigned to the 

same MIDI channel, you cannot assign the same 

Control Change number to both of them.

A Control Change number can be selected from the 

following: 1-5, 7-31, 64-95.

When ON/OFF status is set to ON, a check mark 

appears in the check box. When it is OFF, the box is 

blank. In the figure 11, all the channels are set to ON.

You cannot operate the MIDI control of the channel 

pan when the surround mode is not set to STEREO.

ª

Assigning parameters to rotary encoders

You can assign parameters to the rotary encoders using the 

four encoder mode keys (please refer to the “Encoders” 

section on page 20 in the Owner’s Manual).

In the previous versions of DM-3200, parameters were 

pre-assigned as indicated next to each of the encoder mode 

keys. In Version 1.20 you can select which parameter is to 

be controlled by which of the encoder mode keys.

Figure 12: OPTION>ENCODER MODE scree

Parameters are assigned on the 

ENCODER MODE

 screen, 

which is a sub-screen newly added to the 

OPTION

 screen.

1  Press the 

OPTION

 key to display the 

OPTION

 screen, 

then use the 

POD 4

 knob (or press the 

OPTION

 key 

again) to display the 

ENCODER MODE

 sub-screen.