Tascam DM-3200 Release Notes - Dm-3200 Release Notes
DM-3200 Release Notes
16
TASCAM DM-3200 Release Notes
: output low pulse at the designated time
: output high pulse at the designated time
: change to low level at the designated time
: change to high level at the designated time
ON/OFF setting
•
Set this to
ON
when you want to activate the settings of
individual
GPI
ports.
Editing the GPI EVENT LIST
You can edit the
GPI EVENT LIST
by highlighting the button
at the bottom right on the screen and then by pressing the
ENTER
key.
SORT PORT
: This sorts the
GPI EVENT LIST
by port numbers.
SORT TIME
: This sorts the
GPI EVENT LIST
by time.
CAPTURE TC
: This sets the
TIME
of the highlighted time
event to the current timecode value.
DELETE
: This deletes the highlighted time event.
NOTE
You can scroll within the GPI EVENT LIST while the
cursor is pointing at CAPTURE TC or DELETE using the
JOG/DATA dial. The JOG/DATA dial icon at the upper
right corner of the list will become black.
ª
Expanded dynamic automation function
Additional dynamic automation parameters
The following parameters can now be captured and
re-played by the dynamic automation function of DM-3200
(please see “Automated Controls” on the page 4 of the
DM-3200 Automation Guide).
Image
•
Image parameter of the linked channel (please see “Pan
and balance settings” on page 71 of the DM-3200 Owner’s
Manual).
Effect
•
Common effect parameters (
TYPE
,
INPUT
,
MIX
,
BYPASS
,
OUTPUT
) and TASCAM effect parameters (please see
“Setting up the effects” on page 82 of DM-3200 Owner’s
Manual).
Assignments
•
This includes, in addition to the buss assignment and stereo
buss assignment, the AUX 1-2 assignment from the BUSS
and STEREO BUSS, surround assignment and ON/OFF
setting of CSP/LFE speakers (please see “Channel-to-buss
assignment” on page 51 and “Assigning channels to surround
busses” on page 75 of the DM-3200 Owner’s Manual).
NOTE
When any of the above mentioned parameters is a
continuous variable, the Revert function is applied to it.
On the AUTO CONFIG screen, each of these addi-
tional parameters is related to an item as shown
below (please see “AUTO CONGIG” on page 14 of the
DM-3200 Automation Guide).
Parameter
Item
IMAGE
Assign Swtch
Effect 1 parameters
Effect 2 parameters
PAN/BAL
BUSS ASSIGN
EFFECT 1
EFFECT2
Additional parameters that are re-played as
Initial Status
The following parameters are now captured and re-played
as the Initial Status of the automation (please see “Initial
Status” on page 32 of DM-3200 Automation Guide).
Trigger source of the compressor
•
Trigger source of the gate
•
•
ROUTING>INPUT
screen setting
•
ROUTING>OUTPUT
screen setting
•
ROUTING>INSERT
screen setting
Pan mode setting
•
Surround pan mode setting
•
Direct assignments setting
•
Pan gang button setting
•
Digital trim value setting
•
Phase setting
•
Mono switch setting
•
Channel delay value setting
•
Pre/post setting of the channel delay
•
Level setting of BUSS/AUX signal to stereo buss
•
Pan setting of BUSS/AUX signal to stereo buss
•
With these additions, all of the parameters that can be
stored as snapshots are now captured and re-played as the
Initial Status.
Settings prohibited to change during automa-
tion re-play
The following mixer settings cannot be changed while
automation data is being re-played.
Surround mode
•
Grouping setting
•
Channel link setting
•
Pan switch setting [Set by
•
SHIFT + OUTPUT ASSIGN
]
If you try to change the above settings, a pop-up message
“
cannot do this while automation is running
” will appear
and the operation will be denied.