Tascam DM-3200 Release Notes - Dm-3200 Release Notes
DM-3200 Release Notes
TASCAM DM-3200 Release Notes
15
1 Pre-select the item type from the
ITEM SELECT
section at the bottom left of the screen, using the
POD 1
knob.
TIME EVENT
: The GPI port will be controlled by the
designated timecode value.
KEY EVENT
: The status of the transport key,
F1-F12
key, and the status of the
MUTE
key will control the
GPI port.
FADER EVENT
: The GPI port will be controlled by the
status of the fader.
2 Using the cursor key, highlight a cell in the
ITEM
column that you wish to set, and select the item
using the
JOG/DATA
dial.
Depending on which item type is selected in step 1 above,
the options given vary as follows:
TIME EVENT
•
:
TIME EVENT
or no assignment (
------
)
KEY EVENT
•
:
REW
,
FF
,
STOP
,
PLAY
,
REC
,
F1-F1
,
MUTE
(
CH1-48, BUSS1-16, AUX1-8
), or no assignment (
------
)
FADER EVENT
•
:
FADER
(
CH1-48, BUSS1-16, AUX1-8, STEREO
)
or no assignment (
------
)
3 Press the
ENTER
key to confirm the setting.
Selecting the type
•
The Waveform to be output from each of the ports can be
set in the
TYPE
column in the
SETUP
list.
Use the cursor key to highlight a cell in the
TYPE
column
that you want to edit, and select the item using the
JOG/
DATA
dial.
Depending on the type of the item you selected, the options
given vary as follows:
TIME EVENT
:
TYPE
column will show “
------
” and the set-
ting of the type is done in the
GPI EVENT LIST
on the right
of the screen.FADER EVENT
: output low pulse when the fader starts
: output high pulse when the fader starts
: output low pulse when the fader stops
: output high pulse when the fader stops
: output low pulse when the fader starts or stops
: output high pulse when the fader starts or stops
: output changes to low level when the fader
starts, and to high level when the fader stops
: output changes to high level when the fader
starts, and to low level when the fader stops
NOTE
”When the fader starts” means when the fader level is
brought up from the lowest level.
”When the fader stops” means when the fader level is
brought down to the lowest level.
The Output pulse range is approximately 150ms.
KEY EVENT
•
: output low pulse when the key status changes
: output high pulse when the key status changes
: change to low level when the key status is
turned on, and to high level when the key status
is turned off
: change to high level when the key status is
turned on, and to low level when the key status
is turned off
NOTE
The output pulse range is approximately 150ms.
Options for F5-F8 are either low pulse output or high
pulse output.
ON/OFF setting
•
Set this to
ON
when you want to activate each of the
GPI
ports.
When the
TYPE
is set to
TIME EVENT
, it will always display
OFF
and the ON/OFF setting will be governed by the
setting in the
GPI EVENT LIST
on the right of the screen.
TIME EVENT section
You can set up to 16 time events in the
GPI EVENT LIST
.
How to control the GPI EVENT LIST
•
To move the cursor vertically within the list, use either
•
the up and down cursor key or the
POD 4
knob.
To move the cursor horizontally (across the columns),
•
use either the right and left cursor key.
Arrows at the top and the bottom of the right-hand side
•
of the list mean that there are more time events outside
of the screen. To scroll the list vertically, use the
POD
4
knob. You cannot use the up and down cursor key to
scroll the list.
Selecting the port
•
GPI
ports can be selected in the
PORT
column on the
GPI
EVENT LIST
. You can only select a port whose item has been
set to be a
TIME EVENT
in the
GPI CONFIG
section. Use either
the cursor key or the
POD 4
knob to highlight a cell in the
PORT
column that you want to edit, use the
JOG/DATA
dial
to select the port, then press the
ENTER
key to confirm the
selection. You can select the same port for more than one
time event.
Setting the time
•
You can set the time when an event is to be executed. Use
either the
cursor
key or the
POD 4
knob to highlight a cell
in the
TIME
column that you wish to set, use the
JOG/DATA
dial to set the time, then press the
ENTER
key to confirm.
Setting the type
•
You can set the output waveform type for each of the
GPI
ports.
Use either the cursor key or the
POD 4
knob to highlight a
cell in the
TYPE
column that you want to edit, then use the
JOG/DATA
dial to select the type.