WAGNER Plast Coat 25 Operating Manual - Plast Coat 25 · 35
29
Plast Coat 25 · 35
GB
2.1
OPeRAtION OF tHe MORtAR SPRAyING
MACHINeS PlAStCOAt 25 ANd 35
The coating materials are supplied to the machine by means
of the receptacle. The spiral conveyor feeds the coating mate-
rial into an eccentric screw pump. This pump generates the
pressure required for the transport through the mortar hose.
The compressed air necessary for the atomizing of the mate-
rial is fed into the spray lance.
The mortar spraying machine can be switched on and off us-
ing the electrical remote control.
The continuously adjustable feed rate of the coating material
can be used to create a soft, even spraying pattern.
2.2
WHAt MAteRIAlS CAN Be SPRAyed?
• Heatinsulatingcompositesystemadhesive
(mineral and synthetic resin systems)
• Syntheticresinplastersuptograinsizeof5mm
• Silicateplastersuptograinsize5
• Silicateresinplastersuptograinsize5
• Mineralfinalcoatplasteruptograinsize5
• Lightplastersystemsuptograinsize5
• Scrapedrenderinguptograinsize5
• Insulationplaster
• Renovatingplaster
• Foammortarcoating
• Quartzplastic
• Roofcoatings
• Flameproofcoatings
• Mineralsealingslurries
• Bitumenemulsions
• Reinforcingfiller
• Liquidwoodchip
• Framesealingmortar
• Syntheticresinrenderingbase
• Primer
• Fillingpaints,incl.fibercontaining
• Elasticcoatings
• Acousticplaster,syntheticresinbonded
• Filler,syntheticresinbonded
• Concretetrowel
All coating materials should be suitable for applying using
machines. See product data sheet for the coating material to
be used.
Only use other materials after prior consultation with the
manufacturer or WAGNER application technology dept.
3
teCHNICAl dAtA
PlastCoat 25
PlastCoat 35
Voltage:
230 V ~, 50 Hz
400 V, 50 Hz V3 ~
Fuse protection:
16 A slow-blow
Device mains cable
6 m long:
3 x 2.5 mm
2
5 x 1.5 mm
2
Motor output P
1
:
2.2 kW
3.6 kW
Max. feed rate (water):
Pump yellow:
Pump brown:
Pump green:
10 l/min
15 l/min
20 l/min
15 l/min
20 l/min
25 l/min
Max. operating pressure:
40 bar
Max. grain size:
K5 mm
Measurements L x W x H:
1200 x 520 x 660 mm
Receptacle capacity:
60 l
Weight:
85 kg
87 kg
Tire pressure, max.:
2 bar
Protective system:
IP 54
Max. sound pressure level:
77 dB (A)*
Atomization air connection:
Rapid action coupling DN 7 mm
Max. atomization air pres-
sure:
10 bar
Required volume of
compressed air, min:
220 l/min
Texture nozzle:
8 mm (standard)
Mortar hose:
DN 27 mm, 10 m (standard)
* Measuring point: At a distance of 1m to the side of the unit and
at a height of 1.60 m above floor, reverberant floor.
2
INtROduCtION tO WORkING
WItH tHe MORtAR SPRAyING
MACHINeS PlAStCOAt 25 ANd 35
The mortar spraying machines can be combined with continu-
ous flow, gravitation compulsory or pan mixers for the process-
ing of mineral coating materials.
The container suction system (accessory) can be used to suck
directly from a container.
IntroductIon to workIng wIth the motar sprayIng machInes/ technIcal data