- DL manuals
- Yamaha
- Other
- TF1
- Service Manual
Yamaha TF1 Service Manual - Tf1 Disassembly Procedure
TF5/TF3/TF1
67
TF1 DISASSEMBLY PROCEDURE
(TF1 分解手順)
Precautions(注意事項)
Take care not to trap your fingers.
* Install the filament tape and the harness clamp in the same
way as they were before removal.
* Notes on Flat Cable
Contacts are visible from the back. Pay attention not to
insert and install the cable to the connector inversely.
(Photo 1)
* MAC (Media Access Control) address are stored in the
MAIN circuit board. If the MAIN circuit board are replaced,
MAC address will be changed.
* Before proceeding to procedures, prepare panel stay (tools
for fixing the control panel) in advance. (Photo 2)
作業中は指を挟まない様に注意してください。
※
フィラメントテープ、束線止めは、取り外す前と同じよ
うに取り付けてください。
※
フラットケーブルの注意
接点が裏面から透けて見えます。コネクタにケーブルの
表・裏を逆に差込まないように注意して取り付けてくだ
さい。(写真 1)
※
MAIN シートには、MAC(Media Access Control)アド
レスが設定されています。MAIN シートを交換すると、
MAC アドレスが変更されます。
※
作業を行う前に、パネルステー(コントロールパネル固
定用工具)を用意してください。(写真 2)
Photo 1(写真 1)
Photo 2(写真 2)
Front Side(表面)
Back Side(裏面)
PANEL STAY(パネルステー)
(ZG961200)
Summary of TF1
Page 1
Tf5/tf3/tf1 46 1. Side pad r assembly, side pad l assembly (time required: about 1 minute each) 1-1 side pad r assembly : 1-1-1 remove the two (2) screws marked [80a]. The side pad r assembly can then be removed. (fig. 1) 1-2 side pad l assembly : 1-2-1 remove the two (2) screws marked [80b]. The si...
Page 2
Tf5/tf3/tf1 47 fig. 1(図 1) r3fnpwfuif4*%&1"%3"44&.#-:boe4*%&1"%-"44&.#-: * this figure is the side pad r assembly. (サイドパッド rアッセンブリとサイドパッド lアッセンブリの外し方) (この図はサイドパッド rアッセンブリです。) 㻝 㻞 㻟 㻝 㻞 㻟 [80a] [50] [50] [40] [30] [80b] a a a a side pad r assembly (サイドパッド rアッセンブリ) side pad l assembly (サイドパッド lアッセンブリ)...
Page 3
Tf5/tf3/tf1 48 fig. 2(図 2) fig. 3(図 3) photo 3(写真 3) • installing the panel stay (パネルステーの取り付け方) bottom assembly 24 (ボトム ass'y 24) control panel assembly 24 (コンパネ ass'y 24) bottom assembly 24 (ボトム ass'y 24) panel stay (パネルステー) bottom assembly 24 (ボトム ass'y 24) control panel assembly 24 (コンパネ ass'y 24...
Page 4
Tf5/tf3/tf1 49 3. Lithium battery (time required: about 5 minutes) 3-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) 3-2 fix the control panel assembly 24. (see procedure 2) 3-3 the lithium battery on the main circuit board can be replaced. (fig. 1, fig. 5) * after removi...
Page 5
Tf5/tf3/tf1 50 fig. 6(図 6) a. Disassembly procedure of bottom assembly 24 a-1. Da2 circuit board (time required: about 9 minutes) a-1-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-1-2 fix the control panel assembly 24. (see procedure 2) a-1-3 remove the seventeen (17)...
Page 6
Tf5/tf3/tf1 51 a-2. Da1 circuit board (time required: about 12 minutes) a-2-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-2-2 fix the control panel assembly 24. (see procedure 2) a-2-3 remove the da2 circuit board. (see procedure a-1) a-2-4 remove the sixteen (16) scr...
Page 7
Tf5/tf3/tf1 52 a-4. Brdg circuit board, main circuit board (time required: about 15 minutes) a-4-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-4-2 fix the control panel assembly 24. (see procedure 2) a-4-3 remove the da2 circuit board. (see procedure a-1) a-4-4 remove...
Page 8
Tf5/tf3/tf1 53 fig. 7(図 7) remove the shield ps assembly. (シールド psアッセンブリの外し方) a b bottom assembly 24 (ボトム ass'y 24) bottom assembly 24 (ボトム ass'y 24) (背面) > (上面) > [346] [230] [240] [390] silicon plate b (珪素鋼板プレート b) shield ps assembly (シールド ps アッセンブリ) shield ps assembly (シールド ps アッセンブリ) support ang...
Page 9
Tf5/tf3/tf1 54 fig. 8(図 8) fig. 9(図9) bottom assembly 24 (ボトム ass'y 24) opt angle (opt アングル) main notch (切り欠き) notch (切り欠き) a b bottom assembly 24 (ボトム ass'y 24) bottom assembly 24 (ボトム ass'y 24) (背面) > (上面) > [290] [295] [200] *1 main ps main ps [310] [320] lithium battery (リチウム電池) a a.
Page 10
Tf5/tf3/tf1 55 [230] [240] [390] shield ps assembly (シールドpsアッセンブリ) shield ps assembly (シールドpsアッセンブリ) support angle (サポートアングル) note : installation of shield ps assembly 注意 : シールドpsアッセンブリの取り付け note : installation of support angle 注意 : サポートアングルの取り付け cable of dc fan motor (dcファンモーターのケーブル) rear panel 24 ...
Page 11
Tf5/tf3/tf1 56 a-6. Dc fan motor (time required: about 17 minutes) a-6-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-6-2 fix the control panel assembly 24. (see procedure 2) a-6-3 remove the da2 circuit board. (see procedure a-1) a-6-4 remove the da1 circuit board. (s...
Page 12
Tf5/tf3/tf1 57 a r"wjfx(a視図) 3fbswjfx (背面) > 5pqwjfx (上面) > [180] bottom assembly 24 (ボトム ass'y 24) dc fan motor (dcファンモーター) fan holder (ファンホルダー) dc fan motor (dcファンモーター) [140] [140] [140] [182] [130] (アース端子) earth terminal acin connector assembly(acin束線) acin connector assembly (acin束線) acin connec...
Page 13
Tf5/tf3/tf1 58 b. Disassembly procedure of control panel assembly 24 b-1. Lcdc circuit board (time required: about 6 minutes) b-1-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-1-2 remove the control panel assembly 24. (see procedure 2) b-1-3 remove the four (4) screws...
Page 14
Tf5/tf3/tf1 59 b-2. 液晶ディスプレイ (所要時間:約 6 分) b-2-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-2-2 コンパネ ass'y 24 を外します。(2 項参照) b-2-3 [400] のネジ 4 本を外して、lcd シールドを外し ます。(図 15) ※ lcd シールドを取り付ける際は、図 16 を参照してく ださい。 b-2-4 液晶ディスプレイを外します。(図 15、図 17) ※ 液晶ディスプレイを取り付ける際は、図 17 を参照し てください。 b-2. Crystal display (t...
Page 15
Tf5/tf3/tf1 60 b-3. Phn シート (所要時間:約 6 分) b-3-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-3-2 コンパネ ass'y 24 を外します。(2 項参照) b-3-3 コントロールパネル面より、[100] のノブ 1 個と 六角ナット 1 個とワッシャー 1 個外します。 (図 18) b-3-4 [550] のネジ 1 本を外して、phn シートを外しま す。(図 14) b-4. Pnps シート (所要時間:約 6 分) b-4-1 サイドパッド r アッセンブリとサイドパッド l アッセンブ...
Page 16
Tf5/tf3/tf1 61 b-5. Pnc シート (所要時間:約 11 分) b-5-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-5-2 コンパネ ass'y 24 を外します。(2 項参照) b-5-3 phn シートを外します。(b-3 項参照) b-5-4 pnps シートを外します。(b-4 項参照) b-5-5 lcd シールドを外します。(b-2-3 項参照) b-5-6 コントロールパネル面より、[90a] のエンコーダ 6 個と [105] の管用ナット 1 個と [106] の皿バネ座金 1 個と [110] の t...
Page 17
Tf5/tf3/tf1 62 ref no. Description (部品名) quantity (数量) [460] button sel cue(ボタン sc)(st in 1 sel/cue, st in 2 sel/cue) 2 [470] button on(ボタン on)(st in 1 on, st in 2 on) 2 [480] button unit case(ボタンユニットケース) 2 fig. 20 (図20) b-6. Pnl シート (所要時間:約 7 分) b-6-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-...
Page 18
Tf5/tf3/tf1 63 b-8. Fdps (1–3) circuit board (time required: about 6 minutes each) b-8-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-8-2 remove the control panel assembly 24. (see procedure 2) b-8-3 remove the two (2) screws marked [1010]. The fdps circuit board can t...
Page 19
Tf5/tf3/tf1 64 b-9. Pnfd8 (1–3) circuit board, oled case assembly b-9-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-9-2 remove the control panel assembly 24. (see procedure 2) b-9-3 remove the fdps circuit board. (see procedure b-8) b-9-4 pnfd8 circuit board (time req...
Page 20
Tf5/tf3/tf1 65 b-10. Pnfd1 circuit board (time required: about 6 minutes) b-10-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-10-2 remove the control panel assembly 24. (see procedure 2) b-10-3 remove the fi ve (5) screws marked [910]. The pnfd1 circuit board can then ...
Page 21
Tf5/tf3/tf1 66 b-11. Pnf circuit board (time required: about 6 minutes) b-11-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-11-2 remove the control panel assembly 24. (see procedure 2) b-11-3 remove the six (6) screws marked [750]. The pnf circuit board can then be rem...
Page 22: Tf1 Disassembly Procedure
Tf5/tf3/tf1 67 tf1 disassembly procedure (tf1 分解手順) precautions(注意事項) take care not to trap your fingers. * install the filament tape and the harness clamp in the same way as they were before removal. * notes on flat cable contacts are visible from the back. Pay attention not to insert and install t...
Page 23
Tf5/tf3/tf1 68 1. Side pad r assembly, side pad l assembly(サイドパッドRアッセンブリ、サイドパッドLアッセンブリ) ....... 69 2. Control panel assembly 16(コンパネ ass'y 16) ....................................................................................................... 69 3. Lithium battery(リチウム電池) ..........................
Page 24
Tf5/tf3/tf1 69 1. Side pad r assembly, side pad l assembly (time required: about 1 minute each) 1-1 side pad r assembly : 1-1-1 remove the two (2) screws marked [80a]. The side pad r assembly can then be removed. (fig. 1) 1-2 side pad l assembly : 1-2-1 remove the two (2) screws marked [80b]. The si...
Page 25
Tf5/tf3/tf1 70 fig. 1(図 1) r3fnpwfuif4*%&1"%3"44&.#-:boe4*%&1"%-"44&.#-: * this figure is the side pad r assembly. (サイドパッド rアッセンブリとサイドパッド lアッセンブリの外し方) (この図はサイドパッド rアッセンブリです。) 㻝 㻞 㻟 㻝 㻞 㻟 [80a] [50] [50] [40] [30] [80b] a a a a side pad r assembly (サイドパッド rアッセンブリ) side pad l assembly (サイドパッド lアッセンブリ)...
Page 26
Tf5/tf3/tf1 71 fig. 2(図 2) fig. 3(図 3) photo 3(写真 3) • installing the panel stay (パネルステーの取り付け方) bottom assembly 16 (ボトム ass'y 16) control panel assembly 16 (コンパネ ass'y 16) panel stay (パネルステー) bottom assembly 16 (ボトム ass'y 16) control panel assembly 16 (コンパネ ass'y 16) control panel assembly 16 (コンパネ ...
Page 27
Tf5/tf3/tf1 72 3. Lithium battery (time required: about 5 minutes) 3-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) 3-2 fix the control panel assembly 16. (see procedure 2) 3-3 the lithium battery on the main circuit board can be replaced. (fig. 1, fig. 5) * after removi...
Page 28
Tf5/tf3/tf1 73 fig. 6(図 6) a. Disassembly procedure of bottom assembly 16 a-1. Da2 circuit board (time required: about 8 minutes) a-1-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-1-2 fix the control panel assembly 16. (see procedure 2) a-1-3 remove the seventeen (17)...
Page 29
Tf5/tf3/tf1 74 a-2. Da1 circuit board (time required: about 11 minutes) a-2-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-2-2 fix the control panel assembly 16. (see procedure 2) a-2-3 remove the da2 circuit board. (see procedure a-1) a-2-4 remove the sixteen (16) scr...
Page 30
Tf5/tf3/tf1 75 a-4. Main circuit board (time required: about 17 minutes) a-4-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-4-2 fix the control panel assembly 16. (see procedure 2) a-4-3 remove the da2 circuit board. (see procedure a-1) a-4-4 remove the haad (1) circui...
Page 31
Tf5/tf3/tf1 76 fig. 7(図 7) remove the shield ps assembly. (シールド psアッセンブリの外し方) a b bottom assembly 16 (ボトム ass'y 16) bottom assembly 16 (ボトム ass'y 16) (背面) > (上面) > [346] [230] [240] [390] silicon plate b (珪素鋼板プレート b) shield ps assembly (シールド ps アッセンブリ) shield ps assembly (シールド ps アッセンブリ) support ang...
Page 32
Tf5/tf3/tf1 77 fig. 8(図 8) fig. 9(図9) bottom assembly 16 (ボトム ass'y 16) opt angle (opt アングル) main notch (切り欠き) notch (切り欠き) a b bottom assembly 16 (ボトム ass'y 16) bottom assembly 16 (ボトム ass'y 16) (背面) > (上面) > [290] [295] [200] *1 main ps main ps [310] [320] lithium battery (リチウム電池) a a.
Page 33
Tf5/tf3/tf1 78 [230] [240] [390] shield ps assembly (シールドpsアッセンブリ) shield ps assembly (シールドpsアッセンブリ) support angle (サポートアングル) note : installation of shield ps assembly 注意 : シールドpsアッセンブリの取り付け note : installation of support angle 注意 : サポートアングルの取り付け cable of dc fan motor (dcファンモーターのケーブル) rear panel 16 ...
Page 34
Tf5/tf3/tf1 79 a-6. Dc fan motor (time required: about 16 minutes) a-6-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) a-6-2 fix the control panel assembly 16. (see procedure 2) a-6-3 remove the da2 circuit board. (see procedure a-1) a-6-4 remove the da1 circuit board. (s...
Page 35
Tf5/tf3/tf1 80 a r"wjfx(a視図) 3fbswjfx (背面) > 5pqwjfx (上面) > [180] bottom assembly 16 (ボトム ass'y 16) dc fan motor (dcファンモーター) fan holder (ファンホルダー) dc fan motor (dcファンモーター) [140] [140] [140] [182] [130] (アース端子) earth terminal acin connector assembly(acin束線) acin connector assembly (acin束線) acin connec...
Page 36
Tf5/tf3/tf1 81 b. Disassembly procedure of control panel assembly 16 b-1. Lcdc circuit board (time required: about 6 minutes) b-1-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-1-2 remove the control panel assembly 16. (see procedure 2) b-1-3 remove the four (4) screws...
Page 37
Tf5/tf3/tf1 82 b-2. 液晶ディスプレイ (所要時間:約 5 分) b-2-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-2-2 コンパネ ass'y 16 を外します。(2 項参照) b-2-3 [400] のネジ 4 本を外して、lcd シールドを外し ます。(図 15) ※ lcd シールドを取り付ける際は、図 16 を参照してく ださい。 b-2-4 液晶ディスプレイを外します。(図 15、図 17) ※ 液晶ディスプレイを取り付ける際は、図 17 を参照し てください。 b-2. Crystal display (t...
Page 38
Tf5/tf3/tf1 83 b-3. Phn シート (所要時間:約 5 分) b-3-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-3-2 コンパネ ass'y 16 を外します。(2 項参照) b-3-3 コントロールパネル面より、[100] のノブ 1 個と 六角ナット 1 個とワッシャー 1 個外します。 (図 18) b-3-4 [550] のネジ 1 本を外して、phn シートを外しま す。(図 14) b-4. Pnps シート (所要時間:約 5 分) b-4-1 サイドパッド r アッセンブリとサイドパッド l アッセンブ...
Page 39
Tf5/tf3/tf1 84 b-5. Pnc シート (所要時間:約 10 分) b-5-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-5-2 コンパネ ass'y 16 を外します。(2 項参照) b-5-3 phn シートを外します。(b-3 項参照) b-5-4 pnps シートを外します。(b-4 項参照) b-5-5 lcd シールドを外します。(b-2-3 項参照) b-5-6 コントロールパネル面より、[90a] のエンコーダ 6 個と [105] の管用ナット 1 個と [106] の皿バネ座金 1 個と [110] の t...
Page 40
Tf5/tf3/tf1 85 ref no. Description (部品名) quantity (数量) [460] button sel cue(ボタン sc)(st in 1 sel/cue, st in 2 sel/cue) 2 [470] button on(ボタン on)(st in 1 on, st in 2 on) 2 [480] button unit case(ボタンユニットケース) 2 fig. 20 (図20) b-6. Pnl シート (所要時間:約 6 分) b-6-1 サイドパッド r アッセンブリとサイドパッド l アッセンブリを外します。(1 項参照) b-...
Page 41
Tf5/tf3/tf1 86 b-8. Fdps (1–2) circuit board (time required: about 5 minutes each) b-8-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-8-2 remove the control panel assembly 16. (see procedure 2) b-8-3 remove the two (2) screws marked [1010]. The fdps circuit board can t...
Page 42
Tf5/tf3/tf1 87 b-9. Pnfd8 (1–2) circuit board, oled case assembly b-9-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-9-2 remove the control panel assembly 16. (see procedure 2) b-9-3 remove the fdps circuit board. (see procedure b-8) b-9-4 pnfd8 circuit board (time req...
Page 43
Tf5/tf3/tf1 88 b-10. Pnfd1 circuit board (time required: about 6 minutes) b-10-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-10-2 remove the control panel assembly 16. (see procedure 2) b-10-3 remove the fi ve (5) screws marked [910]. The pnfd1 circuit board can then ...
Page 44
Tf5/tf3/tf1 89 b-11. Pnf circuit board (time required: about 6 minutes) b-11-1 remove the side pad r assembly and side pad l assembly. (see procedure 1) b-11-2 remove the control panel assembly 16. (see procedure 2) b-11-3 remove the six (6) screws marked [750]. The pnf circuit board can then be rem...
Page 45: Lsi Pin Description
90 tf5/tf3/tf1 lsi pin description (lsi 端子機能表) ak4396vf-e2 (x8324a00) dac (digital to analog converter) ............................................................91 am3352bzcz60 (yf449b00) microprocessor (mpu) ..........................................................92-93 cs4385a-dqzr (yf811a00) ...