Zebra ® xi iii plus ™ industrial/commercial printer quick reference guide da kort funktionsoversigt guida rapida it de kurzanleitung naslaggids nl el Οδηγός γρήγορης αναφοράς hurtiganvisning no es guía de referencia rápida skrócony opis pl fi pikaopas guia de referência rápida pt fr guide de référen...
©2004 zih corp. All product names and numbers are zebra trademarks, and zebra, the zebra logo, zebranet, zpl, and zpl ii are registered trademarks of zih corp. All rights reserved. Adobe ® and acrobat ® are registered trademarks of adobe systems incorporated. All other trademarks are the property of...
English 11347lb r4 6/4/04 en-1 zebra xi iii plus quick reference guide this quick reference guide contains basic information on how to install and operate the printer as well as some simple adjustments that can be performed by the operator; however, it is not comprehensive. Contact your distributor ...
En-2 11347lb r4 6/4/04 english specifications electrical • 90–264 vac; 48–62 hz environmental range operating • 41°f (5°c) to 104°f (40°c) • 20% to 85% non-condensing relative humidity storage • –40°f (–40°c) to 140°f (60°c) • 5% to 85% non-condensing relative humidity fuses the 110 xi iii plus does...
English 11347lb r4 6/4/04 en-3 media and ribbon loading media loading figure 1 • media loading—printer components figure 2 • media loading modes.
En-4 11347lb r4 6/4/04 english roll media loading in tear-off mode ( figure 2 -a) 1. From the front panel, select the appropriate print mode. 2. Place the media roll ( figure 1 -e) on the media supply hanger ( figure 1 -f) or optional supply spindle. 3. Open the printhead by moving the lever located...
English 11347lb r4 6/4/04 en-5 6. After all of the above steps have been completed, close the printhead open lever to lock the media in place. If not aligned correctly, the material may not rewind properly on the rewind spindle/core; that may, in turn, affect media movement and/or printing. Rewind m...
En-6 11347lb r4 6/4/04 english cutter mode ( figure 2 -e) 1. Make sure that the cutter option is available and installed on the printer. 2. From the front panel, select the appropriate print mode. 3. Load media according to the directions above for tear-off mode, except feed the media through the cu...
English 11347lb r4 6/4/04 en-7 6. Place the ribbon with leader around the ribbon take-up spindle ( figure 4 -c) and wind counterclockwise for several turns. 7. Close the printhead ( figure 4 -b). Figure 4 • ribbon loading removing used ribbon refer to figure 5 . 1. Break the ribbon close to the ribb...
En-8 11347lb r4 6/4/04 english operator controls front panel keys table 2 describes the operation of the front panel keys. Front panel lights table 3 describes the operation of the front panel lights. Table 2 • front panel keys button/key description press to enter/exit pause mode. Figure 6 • front ...
English 11347lb r4 6/4/04 en-9 calibration after you have correctly installed the media and ribbon, turn the printer on. The printer performs a power-on self test (post). When this is complete, the liquid crystal display (lcd) reads “printer ready.” the printer then automatically calibrates. During ...
En-10 11347lb r4 6/4/04 english configuration after you have completed the calibration procedure, you may set printer parameters for your application using the front panel display and the five keys directly below it. The configuration procedure in table 4 contains the information you need to get you...
English 11347lb r4 6/4/04 en-11 sensor type press the oval keys to select web or mark sensing mode. If your media does not have black marks on the back, leave your printer at the default (web) setting. Print method press the oval keys to select the method of printing you want to use: direct thermal ...
En-12 11347lb r4 6/4/04 english preventive maintenance perform the following cleaning activities according to the schedule below. Refer to figure 7 . Printhead and platen roller cleaning inconsistent print quality such as voids in the bar code or graphics may indicate a dirty printhead. For best res...
English 11347lb r4 6/4/04 en-13 1. Open the printhead by moving the printhead lever to the open position. 2. Remove the media and ribbon from the print mechanism. 3. Use zebra’s preventative maintenance kit, part number 47362, or a solution of 90% isopropyl alcohol and 10% deionized water on an appl...
En-14 11347lb r4 6/4/04 english adjustments toggle positioning position the toggle(s) to provide even pressure on the media by sliding them to the desired location. If you are using narrow media and your printer has two toggles, you may position one toggle over the center of the media and slide the ...
English 11347lb r4 6/4/04 en-15 media sensor position adjustments the media sensor must be positioned so that it can detect the “web” between labels or a hole or notch in the media. The factory-set position should be sufficient for most applications. If not, perform the appropriate adjustments. Uppe...
En-16 11347lb r4 6/4/04 english lower media sensor adjustment 1. Locate the lower media sensor assembly ( figure 10 -a) under the rear idler roller. (it is a spring clip holding a circuit board.) 2. Slide the sensor until the two brass-colored infrared emitters are under the upper media sensor. Gent...
Zebra technologies corporation 333 corporate woods parkway vernon hills, illinois 60061.3109 u.S.A. Telephone: +1 847.634.6700 facsimile: +1 847.913.8766 zebra technologies europe limited zebra house the valley centre, gordon road high wycombe buckinghamshire hp13 6eq, uk telephone: +44 (0) 1494 472...
