Bakers & Chefs 9905TB Assembly & Operating Instructions - Safety Instructions
Safety Instructions
DANGER: If you smell or hear the hiss of
escaping gas from the LP gas cylinder:
Get away from the LP gas cylinder.
Do not attempt to correct the problem
yourself.
Call your fire department (Do not make the
call from near the LP gas cylinder - your
telephone is an electrical device).
>
>
>
Never connect an unregulated LP gas cylinder to
your grill.
A gas regulator adjusted to have an outlet
pressure of 11" water column (W.C.) is supplied for
connection to the LP gas cylinder. The pressure
regulator and hose assembly supplied with the appli-
ance must be used. Replacement pressure regulators
and hose assemblies must be those specified by the
appliance manufacturer.
SAFETY !
BEWARE
OF
SPIDERS
CAUTION: BURNER TUBES MUST BE IN-
SPECTED AND CLEANED BEFORE FIRST
USE
Spiders and small insects occasionally spin
webs or make nests in the burner tubes during
warehousing and transit. These webs can lead
to a gas flow obstruction which could result in
a fire in and around the burner tubes. This
type of fire is known as "FLASH-BACK" and
can cause serious damage to your grill and
create an unsafe operating condition for the
user. Although an obstructed burner tube is
not the only cause of "FLASH-BACK" it is the
most common cause and frequent inspection
and cleaning of the burner tubes is necessary.
Have the LP gas cylinder filled by a reputable LP gas
dealer, and visually inspected and re-qualified at each
filling.
Have your LP gas dealer check the release valve after
every filling to assure that it remains free of defects.
Always keep cylinder in an upright position. Always
close the cylinder valve when the grill is not in use.
Do not subject LP gas cylinder to excessive heat.
Never store your LP gas cylinder indoors. If you store
your grill indoors, ALWAYS disconnect LP gas
cylinder FIRST, and store LP gas cylinder safely
outside.
When the appliance is not in use, the gas must
be turned off at the supply cylinder.
Storage of an appliance indoors is permissible only
if the cylinder is disconnected and removed from the
appliance.
Cylinders must be stored outdoors in a well-ventilated
area out of the reach of children. Disconnected
cylinders must not be stored in a building, garage or
any other enclosed area.
HOSE ASSEMBLY SAFETY
Check tank valve features to ensure it has proper
external mating threads. (Type 1 connection per 10-
94 AGA Requirement)
Make sure all burner valves are in their off position.
Inspect valve connections port and regulator assem-
bly. Look for any damage or debris. Remove any
debris. Inspect hose for damage. Never attempt to
use damaged or plugged equipment. See your local
LP gas dealer for repair.
When connecting regulator assembly to the tank
valve, hand tighten nut clockwise to a positive stop. Do
Not use a wrench to tighten. Use of a wrench may
damage quick coupling nut and result in a hazardous
condition.
Open tank valve fully (counter-clockwise). Use a
soapy water solution to check all connections for
leaks before attempting to light grill. If a leak is found,
turn tank valve off and do not use grill untill repairs can
be made by a local LP gas dealer.
2.
3.
4.
5.
6.
a) Turn the burner valve off.
b) Turn the tank valve off fully.( Turn clockwise to stop.)
c) Detach the regulator assembly from tank valve by
turning the quick coupling nut counter-clockwise.
To disconnect LP gas cylinder:
The hose assembly must be inspected before each use of
the appliance. If it is evident there is excessive abrasion
or wear; or the hose is cut, it must be replaced prior to the
appliance being put into operation.
TO CONNECT THE LP GAS SUPPLY CYLINDER,
PLEASE FOLLOW THESE STEPS:
Make sure tank valve is in its full off position. (Turn
clockwise to stop)
1.
PAGE 3