FAAC E124 Manual - page 15
3
DL 2
DL
DL 3
DL 2
DL
DL 3
DL 2
DL
DL 3
DL 2
DL
DL 3
ENGLISH
7.
PROGRAMMING
To program the operation of the automated system, you must
access the “PROGRAMMING” mode.
Programming is in two parts: st LEVEL, 2nd LEVEL.
Onactivationoftheboard,thedisplayshows
boand,for3seconds,thefwversionofthe
board.
Thestatusoftheautomatedsystemisshown
onthedisplay.If“PC”appearsonthedisplay
whentheFpush-buttonispressed,thismeans
thatprogrammingwiththePCisloadedonthe
board.Ifnopasswordwasset,youcanonly
modifyparameters
Lo
-
PA
-
Pb
.Tomodifythe
other programming parameters, reload the
defaultofthemotorused(inthiscasethePC
programmingwillbereplacedbythedefault
parametersoftheboard)
IfdFappearsonthedisplaywhenyoupress
keyF(andholditdown),thismeansthatyou
have entered 1st level programming (see
parag.7.1).
Modification of the programming
parametersisimmediatelyeffective,whereas
definitive memory-storage occurs only on
exiting programming and returning to the
viewoftheinputsstatus.Ifyoucutpowerto
theequipmentbeforereturningtoviewthe
inputsstatus,allthemodificationsmadewill
belost.
You can return to the inputs status display,
and save all the parameters modified up
tillthen,fromanypointof1stand2ndlevel
programmingbysimultaneouslypressingkeys
Fand-.
To restore the default settings, recharge the
requireddefaultduringthefirstpassageof1st
levelprogramming.
7.1. 1
ST
LEVELPROGRAMMING
If
PC
appears when you press any button on the display, this means that programming from the PC with a protection password
is loaded on the board. Nothing can be modified without the PC and relevant protection password. Connect the PC to the uSB
to view and/or modify programming, using the dedicated instruction.
Press push-button F to access
st
level programming.
If you press key F (and hold it down) the name of the function appears on the display.
If you release the push-button, the display shows the value of the function, which can be changed with keys + and -.
If you press F again (and hold it down), the display shows the name of the next function, etc.
When you have reached the last function, press key F to exit programming and save the parameters. The display resumes
showing the automated system status.
•
•
•
•
ENCODERWIRINGFOROPERATORS450H
*
LEAF1OPENSASFIRSTANDCLOSESASSECOND.
IFTHEREISNOREBATEBETWEENLEAF1AND2,
SETTHELEAFDELAYTOZEROONTHECONTROL
BOARD.
REVERSE THE ENCODER WIRES TO EXCHANGE
BETWEENTHEENCODERASSOCIATEDWITHLEAF
1ANDTHEENCODERASSOCIATEDWITHLEAF2,
ANDVICEVERSA
THROUGH THE BRACKET COVERING
HOUSING MAKE SURE THAT LED DL1 IS
LIGHTED ON LEAF 2, WHEN THE MOTOR
IS AT REST
LEAF 2
ONE LED ON
THROUGH THE BRACKET COVERING
HOUSING, MAKE SURE THAT LEDs DL1
AND DL2 ARE LIGHTED ON LEAF 1,
WHEN THE MOTOR IS AT REST
LEAF 1
TWO LEDs ON
LEAF 1*
THROUGH THE BRACKET COVERING
HOUSING MAKE SURE THAT LED DL1 IS
LIGHTED ON LEAF 2, WHEN THE MOTOR
IS AT REST
LEAF 1
TWO LEDs ON
LEAF 2
ONE LED ON
THROUGH THE BRACKET COVERING
HOUSING, MAKE SURE THAT LEDs DL1
AND DL2 ARE LIGHTED ON LEAF 1,
WHEN THE MOTOR IS AT REST
LEAF 1*
ENCODERWIRESREVERSINGOPERATION
ENCODER
LEAF1
ENCODER
LEAF2
LEAF 2
LEAF 2