FAAC E124 Manual - page 24
22
a
ENGLISH
8
SAVINGTHERADIOCODE
The control unit has an integrated 2-channel decoding system
(DS, SLh, LC/RC) named OMNIDEC. This system makes it possible
to save both total opening (OPEN A) and partial opening OPEN
B) of the automated system - this is made possible by an
additional receiver module (fig.27 ref. a) and radio controls
on the same frequency.
The3typesofradiocodes(DS,LSH,LC/RC)can
coexistsimultaneouslyonthetwochannels.Up
to256radiocodescanbeinput,subdivided
betweenOPENAandOPENB
To use various coding systems on the same
channel,youmustfinishthelearningofeach
systemandthenrepeattheprocedureforthe
other.
Otherprogrammingpossibilitiesoftheradio
channelsarefeasiblebyprogrammingwitha
PC(seededicatedinstructions).E.G.:youcan
setanautomaticOPENcommandontheradio
channel, which commands an automatic
cycle (open-pause-close) irrespective
of the selected logic (see dedicated PC
instructions).
8.1 SAVINGDSRADIOCONTROLS
Amaximumof256codes,subdividedbetween
OPENAandOPENBcanbesaved.
On the DS radio control, select the required ON-OFF
combination for the 2 dip-switches.
Press push-button R (SW) or (SW2) to save respectively total
opening (OPEN A)or partial opening (OPEN B). The relevant
LED starts to flash slowly for 5 sec.
Release the push-button.
Within these 5 sec., press the appropriate push-button on
the radio control.
The relevant LED lights steadily for second and then goes
OFF, indicating that storage was executed.
.
2.
3.
4.
5.
To add other different codes, repeat the procedure from
point .
To add radio controls with the same code, copy the same
ON-OFF combination on the other radio controls.
8.2 SAVINGSLHRADIOCONTROLS
Amaximumof256codes,subdividedbetween
OPENAandOPENBcanbesaved.
On the SLh radio control, simultaneously press and hold
down push-buttons P and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press push-button R (SW) or R2 (SW2) to save respectively
total opening (OPEN A) or partial opening (OPEN B). The
relevant LED starts to flash slowly for 5 sec.
Release the push-button.
Within these 5 sec., while the radio control LED is still flashing,
press and hold down the required push-button on the radio
control (the radio control LED lights up on steady beam).
The LED on the board lights steadily for second and then
goes OFF, indicating that storage was executed.
Release the radio control push-button.
Quickly press twice the push-button of the saved radio
control.
Theautomatedsystemperformsoneopening
operation. Make sure that the automated
system is free of any obstacle created by
personsorthings.
To enable other radio controls with the same system code,
transfer the code of the memory-stored radio control
push-button to the relevant push-button of the radio controls
to be added, observing the following procedure:
On the memory stored radio control, simultaneously
press and hold down push-buttons P and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press the memory stored push-button and hold it down
(the radio control LED lights up on steady beam).
Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing
it only after the double flash of the radio control LED,
which indicates memory storage executed.
Quickly press twice the push-button of the memory
stored radio control.
Theautomatedsystemperformsoneopening
operation. Make sure that the automated
system is free of any obstacle created by
personsorthings.
6.
7.
.
2.
3.
4.
5.
6.
7.
8.
9.
a.
b.
c.
d.
e.
f.
7.3. PROGRAMMINGFROMPC(3
rd
LEVEL)
To access PROGRAMMING FROM PC, use the X-COM module
or connect the uSB cable to the dedicated connector and
consult the dedicated instructions.
Fig. 27