DL manuals
Intermec
Printer
EasyCoder 4420
Installation Instruction Sheet

Intermec EasyCoder 4420 Installation Instruction Sheet

Other manuals for EasyCoder 4420: Installation Manual, User Manual, Developer's Manual, User Manual, Install Manual, User Manual, Supplementary Manual, User Manual, User Manual, User Manual, Getting Started Manual, Quick Start Manual, User Manual

Installation Instruction Sheet - (page 1)

Installation Instruction Sheet - (page 2)

Installation Instruction Sheet - (page 3)

Installation Instruction Sheet - (page 4)

Installation Instruction Sheet - (page 5)

Installation Instruction Sheet - (page 6)

Installation Instruction Sheet - (page 7)

Installation Instruction Sheet - (page 8)

Page of 8

Download

Print this page

Bookmark us

067149-001

4420 and 4440 Cutter Installation Instruction Sheet

This instruction sheet explains how to install a cutter on a 4420 or 4440 printer. The

following procedures cover attaching the cutter to the printer and connecting the

cutter to the main printed circuit board (PCB). A qualified field service technician

must install the cutter.

Caution

Integrated circuits on printed circuit boards (PCBs) in this equipment are

sensitive to damage by electrostatic discharge (ESD). Prevent ESD by always

wearing skin contact ground straps firmly attached to the equipment metal

base assembly when working inside of the equipment housing. Failure to

comply may result in damage to PCB components.

To install the cutter

1. Turn off the printer.

2. Unplug the printer AC power cord from the back of the printer.

3. Pull the bottom of the media cover away from the base of the printer, lift the

front of the media cover upward to release it from the printer frame, and lift the

media cover away from the top of the printer.

44XXC.001

Feed/Pause

Power/Data

Alert

Empty/Pause

Intermec

4420

1 2 3 4 5 6 7 Next › »

Summary of EasyCoder 4420

Page 1
067149-001 1 4420 and 4440 cutter installation instruction sheet this instruction sheet explains how to install a cutter on a 4420 or 4440 printer. The following procedures cover attaching the cutter to the printer and connecting the cutter to the main printed circuit board (pcb). A qualified field ...
Page 2
2 4. Remove the three phillips screws that secure the pcb cover to the main deck and the three phillips screws that secure the pcb cover to the base of the printer. Retain the screws to replace the pcb cover later. Feed/pause power/data alert em pty/pause intermec intermec 4420 44xxc.002 screw (typi...
Page 3
3 7. Holding onto the media access door, pull the front cover and media access door forward and away from the printer. 8. Using the eight phillips screws, replace the front cover without the media access door. 9. If the printer has a metal filler plate attached with screws, remove the two phillips s...
Page 4
4 10. With the screw extrusions toward the cutter connector, hook the bottom of the cutter connector onto the hole in the connector plate, press down on the clip on top of the cutter connector, and press the connector plate onto the cutter connector. Connector plate cutter connector 44xxc.007 11. Us...
Page 5
5 12. Making sure that pin 1 is plugged on the adapter cable and cut on j23, plug the adapter cable into j23 on the main pcb. If the self-strip motor is installed, make sure the adapter cable is not resting against the motor. J23 cutter pin 1 connector plate 44xxc.009 adapter cable caution do not pl...
Page 6
6 attaching the mounting plate feed/pause power/data alert empty/pause intermec 44xxc.011 notch mounting plate thumbscrew 16. Use the bottom two thumbscrews to attach the cutter to the mounting plate. Make sure the cutter cable goes through the notch in the mounting plate. Feed/pause power/data aler...
Page 7
7 17. Plug the cutter cable into the cutter connector at the base of the main deck. 18. Using a straight-slot screwdriver, loosen the screw on the top of the cutter and swing the cutter cover down. Feed/pause power/data alert empty/pause intermec intermec 4420 cutter cover 44xxc.013 19. Check that t...
Page 8
8 20. Swing the cutter cover up and tighten the screw on the top of the cover. 21. Feed the media through the cutter. The media should extend past the opening in the cutter cover. 22. Reinstall the media cover. 23. Plug in the ac power cord. 24. Turn on the printer. 6001 36th avenue west p.O. Box 42...