1. DL manuals
  2. Banner
  3. Accessories
  4. Q4X
  5. Quick start manual

Banner Q4X Quick start manual

Manual is about: Stainless Steel Laser Sensor with Dual Discrete Outputs and IO-Link

Summary of Q4X

  • Page 1

    Quick start guide class 1 laser cmos sensor with dual outputs and io-link. Patent pending. This guide is designed to help you set up and install the q4x sensor with dual discrete outputs and io-link. For complete information on programming, performance, troubleshooting, dimensions, and accessories, ...

  • Page 2

    Output indicator • on—output is on • off—output is off active teach indicators (dyn, fgs, and bgs) • dyn, fgs, and bgs all off—two-point teach mode selected (default) • dyn on—dynamic teach mode selected • fgs on—foreground suppression teach mode selected • bgs on—background suppression teach mode s...

  • Page 3

    Installation install the safety label the safety label must be installed on q4x sensors that are used in the united states. Note: position the label on the cable in a location that has minimal chemical exposure. 1. Remove the protective cover from the adhesive on the label. 2. Wrap the label around ...

  • Page 4

    Wiring diagram 4 1 3 2 10-30v dc ch1 ch2 + – push-pull load load figure 10. Channel 2 as pnp discrete or pfm output 4 1 3 2 10-30v dc ch1 ch2 + – push-pull load remote input figure 11. Channel 2 as remote input 1 4 3 2 key 1 = brown 2 = white 3 = blue 4 = black note: open lead wires must be connecte...

  • Page 5

    No: do not reset to factory defaults yes: reset to factory defaults two-point static teach dynamic teach background suppression foreground suppression top menu sub menu off: no delays enabled on: enable on and/or off delay (set value in delay timer menu) 1 shot, fixed output pulse duration totalizer...

  • Page 6

    Two-point static teach dynamic teach background suppression foreground suppression top menu sub menu off: no delays enabled on: enable on and/or off delay (set value in delay timer menu) 1 shot, fixed output pulse duration total end: exit setup teach selection ch2 output ch2 window size ch2 ** outpu...

  • Page 7

    • dynamic background suppression —dynamic teach sets a single switch point during machine run conditions. The sensor takes multiple samples and the switch point is set between the minimum and the maximum sampled distances. • one-point window (foreground suppression) —one-point window sets a window (...

  • Page 8

    Specifications sensing beam visible red class 1 laser, 655 nm supply voltage (vcc) 10 to 30 v dc (class 2 supply) (10% max ripple within limits) power and current consumption, exclusive of load sensing range—threaded barrel models 600 mm models: 25 mm to 600 mm (0.98 in to 23.62 in) 300 mm models: 2...

  • Page 9

    Excess gain using a 90% white card—100/110/300/310 mm models table 6: excess gain ( excess gain 1 ) response speed (ms) · at 25 mm (100/300 mm models) · at 35 mm (110/310 mm models) · at 100 mm (100/300 mm models) · at 110 mm (110/310 mm models) · at 300 mm (100/300 mm models) · at 310 mm (110/310 m...

  • Page 10

    Performance curves—threaded barrel models minimum separation distance between target and background for: uniform and non-uniform targets 100 mm models 300 mm models minimum separation t arget to background (mm) dimension y distance to target (mm) dimension x target switch point distance background x...

  • Page 11

    Performance curves—flush mount models minimum separation distance between target and background for: uniform and non-uniform targets 110 mm models 310 mm models minimum separation t arget to background (mm) dimension y distance to target (mm) dimension x 0 2 4 6 8 10 12 14 16 18 20 22 0 25 50 75 100...

  • Page 12

    Side rails, or mounted plastic targets. Contact banner engineering if you require assistance setting up a stable reference surface in your application. For detailed instructions for detecting clear or transparent objects, refer to the instruction manual, p/n 190074. 1. Select a reference surface wit...