JabloCom EYE-02 User Manual - 5.5 B������
JR_EYE-02.ENG.MAN.Manual.19.C-2A
- 16 -
EN
EN
U
se
r‘s
G
ui
de
5.5 B
The EYE-02 camera has an internal backup Li-Ion battery, which allows operating in case of the loss of AC power. If used
in any of the predefined profiles, the backup battery allows the camera to operate for approximately 24hours. Any
individual sensor configuration may shorten this period accordingly.
In case of active MIP sensor, the backup time may be as short as 40 % of the original value. In case of simultaneous use of
IR illuminator working during AC failure, the backup time may drop to 20 %.
Please, note that each item of network communication will shorten the backup time rapidly, especially if the camera is
operated in a poor network coverage area.
Using the device with 3G network may also significantly decrease battery backup time!
Battery mode
In certain cases, for example when used in locations where AC power isn’t available, it may be desired to extend the
battery operation duration. In such case you may use the special
BATTERY
mode.
When in the
BATTERY
mode, the EYE-02 camera reduces dramatically its power consumption in WATCH. It logs out from
the GSM network, switches off the short range radio receiver and switches on the motion-in-picture detector only after
ALERT. It means that the EYE-02 camera, while in the
BATTERY
mode, can not be reached by calls or by SMS commands.
Additionally, the external detectors and remote controls cannot be used for the BATTERY mode, too.
The EYE-02 camera keeps all the internal detectors working and reports all events as in the
NORMAL
mode. After an
ALARM, the EYE-02 camera switches on the radio and logs onto the GSM network for 2 minutes. It reacts to calls, SMS
commands and remote controls during these 2 minutes only.
A fully charged battery in the BATTERY mode can operate the EYE-02 camera for up to 30 days.
5.6 M SD
The EYE-02 camera is equipped with an SDmicro memory card slot allowing further extension of the internal storage
capacity. The EYE-02 Camera comes with an inserted 1 or 2GB memory card.
JabloTool DESKTOP software allows you to switch the EYE-02 camera into the USB mode in which you can access the SD
card as a standard flash disc from an attached PC. To switch to the USB mode, display the device state screen, switch it
into the Advanced user mode, choose CONFIG and USB mode.
Other EYE-02 camera functions are blocked during the PC direct access to the SD card.
When exploring the SD card, you will find the following folder structure:
HISTORY
This folder contains files with complete (all details) log of event history. Files are stored sequentially
in the “ev00001.txt” format.
PICTURE
Archive of static JPEG files recorded at ALARMs (For example: “p0065401.jpg”)
VIDEO
Archive of AVI video files recorded during ALARMs (For example: “vid01021.avi”)
config.txt
A file with the current configuration of EYE-02 – can be used for backup or restore of configuration.
Camera keeps more than 10% of free space on the memory card. Automatically deletes old files.
The SDmicro memory card also contains some esential data for camera. In case you replace your card with
another one always use Jablotool to restore data structures.
5.7 R F D
If necessary, the EYE-02 camera can be RESET to the factory default settings following this guide:
Warning: All user settings, contacts and events will be deleted! Memory card will be formated. Events an
files downloaded into the JabloTool DESKTOP software remain in PC.
• Switch off the camera, remove the battery.
• Wait at least 10 seconds.
• Press the power button and while holding it, do the following steps.
• Insert the battery.
• Within 10 seconds connect the AC power adaptor.
• Camera starts producing fast beeps.
• Wait until the camera makes 3 longer beeps and both LEDs (R+G) start flashing. Release the power button.
• Camera resets and restarts into the ENROLL mode.