Gardsman CTC-1132 Installation, Programming, Operating - 2.2. Telephone Settings
5
2.2. Telephone Settings
In Telephone Settings menu, the following
parameters can be programmed at your
discretion.
* T e l . N u m b e r s
R e c o r d N s g
T e s t R e p o r t
2.2.1. Telephone Numbers
z
In Tel. Setting menu, select Tel Numbers,
the screen allows you to set/change/delete
the emergency telephone numbers.
z
A maximum of six numbers can be stored
in priority order (in the order of A. B. … to
F).
<
<
N
N
O
O
T
T
E
E
>
>
)
A, B,… to F represent the priority
number of the six tel. numbers
respectively.
)
If the tel. number for a particular
priority number has not been stored,
three dots are displayed indicating the
memory spot is empty.
)
Only 11 digits can be displayed on the
tel. Numbers list. Non fitting numbers
are indicated with after the incomplete
number.
Store Tel. Numbers
Step 1. Move the curser to the Tel. Number
submenu and press OK key.
The display will show the following
screen when no tel. number has been
entered:
* A
) . . .
B ) . . .
C ) . . .
D ) . . .
E ) . . .
F ) . . .
Step 2. Choose from A to F sets to store your
phone number and press OK key.
The following screen will be shown for
you to enter the phone number.
E
n
t e r n
e w
N
o
. + O K
. . . . . . . . . . . . . . . .
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
)
At least one set phone number
must be entered, or the Panel will
not dial out at the Alarm situation.
Step 3. Key in your phone number.
Step 4. Press OK key.
The screen will then prompt you to
choose:
* V o i c e
R
e
p
o
r t
S M S r e p
o
r t
<
<
N
N
O
O
T
T
E
E
>
>
Voice Reporting
: For an alarm event,
the reporitng is done via playing voice
messages. Available ones are: Burglar,
Medical Emergency, Fire and Panic to
the phone numbers programmed at
this step.
SMS Reporting
: For an alarm event,
the reporting is done via sending pre-
edited SMS messages to the mobile
phone numbers programmed at this
step.
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
)
If you would like to receive fault
status or Latch on/off by SMS, the
first (A) telephone number must be
set as SMS report.
Step 5. Select a preferred reporting style and
press OK key. The screen will return
to the Tel. Number screen to show
you the stored phone number with a
letter V indicting it’s a Voice report
style and a letter S for SMS report
style.
* A ) 2 2 1 8 0 5 5 1 V
B ) 2 6 9 4 0 6 3 3 S
<
<
N
N
O
O
T
T
E
E
>
>
)
The maximum length of a number is
20 digits including ¿ & #. If this
length is reached, the Control Panel
will emit 5 beeps and no key can be
keyed in except key and OK key.
)
While entering the number, the key
is used as backspace. However, if the
number field is empty, pressing the
key, the screen will return to Tel.
Numbers screen.