Karassn KS-200B Series User Manual - page 11
100-Zone Wireless Alarm System
-
15
-
is 120 ambulance warming sound and “03” is 119 fire warning sound. And there
are four levels of alarm volumes, which gradually increase from “00” to “03”.
(9)Open/Close Alarm Host By Hand
Close Alarm Host By Hand:
In turn on state, if it needs to turn off at the moment,
but you don’t want to turn power off ( to avoid setting time again after power off),
you can operate as following:
in standby time (as picture A), press “ ” key for 3 seconds, it will make two short “
Beep” sound, and second display become empty (as picture B), then the alarm host
enters turn-off state, but the time still works normally, and alarm host don’t receive
any signals (except for emergency zone) until turn it on by hand.
Open by hand: Press “ ” for 3 seconds
Close by hand: Press“ ” for 3 seconds
Open Alarm Host By Hand:
In turn off state ( as picture B), press “ ” for 3
seconds, it will make a short “Beep” sound, at the same time, second display works
normally, and return to the normal state as picture A.
Note:
The alarm host enter disarm state, second display like “-------”, after
entering turn-off by hand state, second display is empty till turn on by hand.
8.3 How To Set Telephone Of KS-200B-B Alarm Host
The operation of KS-200B-B alarm host is the same as KS-200B-A. Telephone
should be connected with alarm host to set telephone alarm function, you can set
as following:
Precautions:
1
The telephone used to program should be DTMF (Double Tone Multi-
Frequency) phone. Please turn P/T switch to “T” position.
2
The host should be in disarm state to avoid interrupt settings when alarm occurs.
3
Every step has indicative sound
A short “beep” sound ---means the operation is valid.
A long “beep” sound ----means the operation is invalid.
If something wrong are entered, please press “*” key to cancel.
4
When system enters setup state, the power of telephone is provided by alarm
host, yet the current supply is limited. If you set alarm by hand-free, you may fail
or can’t hear any sound. Therefore you’d better pick up telephone receiver to set.
Program Operations
>
>
、
、
、
、
Picture A
Picture B
100-Zone Wireless Alarm System
-
10
-
according to the effective zone of the detector. The detector should be installed in
hidden location which must in compliance with the defense requirements as far as
possible.
(3)The wiring should be as hidden as possible so as not to be damaged. If the
exposed wiring is inevitable, conduits or plastic pipes should be used to protect the
wires from damaging by rodents (e.g. mouse).
(4)The model and specification of detectors and cables in each zone as well as
the usage of every color wire of inside cables should be labeled on the
constructional drawings.
(5)The constructional drawings should be archived for system maintenance.
7. 2 System Installation And Debugging
(1) Installation Requirements Of PIR Detector
The PIR detector has the highest sensitivity when human body moves parallelly
with the mirror surface and the sensitivity is the lowest when human body moves
vertically against the lens. As a result, the angle and height against the horizontal
surface should be noted during installation, which will greatly affect the defense
area. The installation height and angle are shown as follows:
*Stand off hot or cold sources, e.g. hot /cold air outlet, air-condition outlet,
electric radiators, air-cooling machines and etc. Stand off windows.
*There should be no any barriers within the defense area of detector.
*The detector should be parallel with the wall surface.
*The detector has not waterproof, fog-proof function, so don’t used it outdoors.
(2) Installation Of Alarm Host
*The alarm host should be placed on table which is near to window as far as
possible.
*The alarm host has not explosion-proof function, which cannot be directly
门
2
m