Karassn KS-200B Series User Manual - page 13
100-Zone Wireless Alarm System
-
13
-
press “Function” key, it displays as following:
Hour: press Minute press Function 4
key to set key to set The second group of Timer-open
Enter “The second group of Timer-open” setup state, press “ ” or “ ” key to
adjust the time. After setup is finished, press “Reset” key to exit or press “Function”
key to set “The second group of Timer-close”. The above figure shows that the
second group of Timer-open time is 18:00.
(5)How To Set The Second Group Of Timer-close
press “Function” key, it displays as following:
Hour: press Minute press Function 5
key to set key to set The second group of Timer-close
Enter “The second group of Timer-close” setup state, press “ ” or “ ” key to
adjust the time. After setup is finished, press “Reset” key to exit or press “Function”
key to set “Arm/Disarm”. The above figure shows that the second group of Timer-
close is 18:00.
For example, if the working time of a company is 8:00 am, and the check out time
is 12:00 pm, the check in time is 14:00 pm and the check out time is 18:00 pm, the
startup and shutdown time should be set as follows:
The startup time of the first group is 12:00, the shutdown time of the first group is
14:00.
The startup time of the second group is 18:00, the shutdown time of the second
group is 8:00.
It is recommended to reserve some time for employees to check in ahead of
schedule and stop off after check out so not to cause unnecessary alarms.
1
If you want the alarm host to guard continuously for 24 hours per day, set the
same time for “auto timer-open” and “auto timer-close ”, e.g., “12:00”. Usually,
the ex-factory state is 24-hour continuous defense.
2
After setting timer-open/timer-close time, the system only can enter close
state when timer-close time arrives. From the time the screen shows to the turn off
time, during this period of time, the system still be on state. For example, you want
the timer-close time to be 8:00, you can set the clock to be 7:59, then set the timer-
close time to be 8:00, and press “Reset” key to exit setting state, after entering
turn-off state, and adjust the clock to the present time, at this time, the system is in
>
>
>
>
、
、
100-Zone Wireless Alarm System
-
12
-
setup state, if there are no any operations within 30 seconds, the system will
automatically exit the setup state and return to display time.
(1)How To Set Time
In time display state, press “Function” key, it will show as following:
Hour: press Minute press Function 1
key to set key to set clock setup
at this time, press “ ” or “ ” to adjust the time. Press “Reset” key to exit setup
state, or press “Function” key to set the first group of timer-open time.
(2)How To Set The First Group Of Timer-open
Hour: press Minute press Function 2
key to set key to set The first group of Timer-open
Press “Function” key to enter “The first group of Timer-open time “setup state,
press “ ” or “ ” key to adjust the time. After setup is finished, press “Reset” key
to exit setup state or press “Function” key to set “The first group of Timer-close
time” setup state. The above figure shows that the first group of Timer-open time
is 12:00.
Note:
Timer-open means the alarm host will automatically enter defense/arm state
and begin to receive alarm signals when the time pre-set arrives.
(3)How To Set The First Group Of Timer-close
Press “Function” key, it displays as following:
Hour: press Minute press Function 3
key to set key to set The first group of Timer-close
Enter “The first group of Timer-close ” setup state, press “ ” or “ ” key to adjust
the time, After setup is finished, press “Reset” key to exit or press “Function” key
to set “ the second group of timer-open “The above figure shows that the first group
of Timer-close time is 14:00.
Note: Timer-close time means the alarm host will automatically enter disarm state
and don’t receive any alarm signals, but it still response to emergency buttons and
alarm signal in emergency zone.
Enter auto shutdown state, the alarm host will display as following:
Hour Minute Shutdown
(4)How To Set The Second Group Of Timer-open
>
>
>
>
>
>