Karassn KS-200B Series User Manual - page 7
100-Zone Wireless Alarm System
-
19
-
will hang up automatically, and go on dialing other alarm telephone numbers.
Note:
1
、
If you press“2#” ,it will stop alarming and stop dialing other alarm telephone
numbers.
2
、
If you don’t do any operations ,the alarm unit will hang down this telephone
and dial the next one. And it also will dial this telephone number in next dialing
circle.
9.How To Learn/Delete Code Of Detectors
KS-200B alarm system automatically learn code with detectors, the code of
detector should be learned to alarm host firstly, then the alarm host can receive
alarm signal. Each zone can be learned on detector code, and each zone can be set
to be common zone or emergency zone freely.
Common Zone:
It can’t receive alarm signal when alarm host in disarm state, but it
still response to emergency button on remote controller.
Emergency Zone:
It also refers to 24 hours zone. as long as alarm host is in working
state, It can receive alarm signal whatever alarm host is in arm or disarm state. It
also can use the emergency call to ask for emergency help.
How To Learn/Delete Code Of Detector
In power-off states, press “Function” Key, and power alarm host at the same time,
then release the “Function” key, the screen will show as following:
Function menu 9, learning code state, it is flashing
Learning display, “ ” (over line) it means the zone have been learned. “ ” (middle line)
it means the zone is empty or the code has been deleted.
Zone type: “0” is common zone. “1” is emergency zone.
Zone number display
Press “
” key to choose zone number. Press “
>
” key to change the zone type. After
choosing zone number, Then press “Function Key” to confirm, the alarm host will
make an indicative “beep” sound and display like 01:0- 09. and 09 stop flashing, It
means the zone is empty and enter learning code state to wait for receiving signals.
At this time, you can trigger the detector to emit signal. If alarm host receives the
signal, it will make two indicative “beep, beep” sound. And the “ “ (middle line)
will change to “- ” (under line) automatically, which means you have learned code
successful. Then you can press“
” key to learn code in other zones, or you can
press “Reset” key to exit learning code state.
100-Zone Wireless Alarm System
-
6
-
There are eight functions altogether. Please refer to “ Operation Guide” chapter for
specific operations..
3 “ ” key: It is used to complete setup function together with “Function” key.
4 “Reset” key: When alarm occurs, press this key to stop alarming, and alarm
message will be automatically kept in record. When entering into setup state, press
this key to exit. KS-200B-B alarm host, when alarm occurs, press this key to stop
alarming, at the same time, it stops dialing other telephone numbers, and alarm
message will be automatically kept in record. When entering into setup state, press
this key to exit.
5 Time Display: Usually, it is used to show time, and the second light is flashing.
When alarm occurs, it is used to display alarm time and the second light is
completely on. When entering setup state, it is used to display setup contents and
the second light is completely on.
6 Orientation Display: Usually, it is used to display second. When there is an
alarm, it is used to indicate alarm location (defense area). When entering into
setup state, it is used to display function setup items.
7 Microphone: Only KS-200B-B have this function, please aim at microphone
when recording.
1 Interface Of Alarm Output:
It provides with a group of normal open alarm
output, a group of normal close alarm output and a group of uncontrolled DC+12V
300mA output.
Interface Of Normal Open/Close Alarm Output:
There is a label like
on the rear panel of main unit, the alarm output contact it can load is 1A 120VC or
3A 30VDC, it controls other equipments when alarming. When the power of
controlled equipments larger then the contact it can load, it is not allowed to
directly connect controlled equipments with this interface, it should adopt
middle relay to avoid damaging main unit.
、
>
、
、
、
、
、
1
2
3
4
5
6
7
100-Zone W ireless Alar m System
TIME
ORIENTATION