Karassn KS-200B Series User Manual - page 5
100-Zone Wireless Alarm System
-
21
-
For example: Set the transmit address of KS-200ATI/BTI detector to be “0 TH,
1 TH, 3 TH, 4 TH, then the transmit address code of KS-200DCT detector, KS-
20BW detector, KS-11A Emergency Button should be set as picture 2.
Picture 2
Picture 1 (It is OTH when it is not inserted)
Picture 2 (KS-200DCT Passive PIR Detector It is OTH when it is not connected)
(KS-20BW Wireless Door Sensor KS-11A Wireless Emitter
It is 3TH when it is not inserted It is 3TH when it is not inserted
Note:
The address code can be read according to the position of address jumper. If it is
not inserted, which means it 0TH.
It only can be transferred when the address code of being transferred detector is
exactly the same as that of KS-200ATI/BTI detector.
The power must be off when modifying transfer address code. Make sure it is
right, and power it on to see if the code is right, after modifying the code, it is valid
when powered on again.
Transmitter only can transmit alarm signal in arm state. So it must be armed in time
to make sure the reliability of system.
Remark:
D 0
D 1
D 2
D 3
3
T
H
T
H
4
1
T
H
D0
D3
D2
D1
D0
D3
D2
D1
2
-
+
4TH
1TH
0TH
1
-
+
1
9
18
D0 D1 D2 D3
D0 D1 D2 D3
4TH
1T H
0TH
100-Zone Wireless Alarm System
-
4
-
between AC and DC, and it will indicate when battery power lower.
1.3 Wireless Emitter
KS-50AI Wireless Emitter adopts 8-bit single chip as processing core, and it
provides wired detectors with working power, and transmit on-off alarm signals of
wired detectors to the signal which can be recognized by KS-200B series alarm
host, and it can transmit and be armed/disarmed by remote controller. and it selects
rechargeable battery as backup power, and it can charge by itself, and also can
automatically exchange between AC and DC, and it will indicate when battery
power lower.
2. Definition
Transmit Wirelessly
The detector (emitter) can transmit signals of short-distance wireless detector
to the signals which can be recognized by KS-200B series alarm host. It has
advantages of emit wirelessly and save cost. For example, some building needs to
install 10 PIR detectors, in old way, you need install 10 KS-200ACT detectors, and
you need to consider the backup power and AC power of 10 detectors. If you adopt
transmit wirelessly, you can use one KS-200ATI detector, other 9 detectors can use
short-distance PIR detectors produced by our company (such as KS-200DCT and
so on). So it greatly save cost.
3. Operate Precautions
3.1 Please carefully read this User Manual and pay more attention to labels and
directions on main unit before operation. Check whether all wire connections are
correct and then turn it on to test so as to prevent occurring accidents.
3.2When alarm host is not equipped with backup power or clock module, the
time should be readjusted if power failure occurs.
3.3This alarm host can be equipped with 12V 1.2Ah sealed-acid storage cell.
standby time is longer than 24 hours, if power failure often occurs in some defense
area, batteries with larger capacity are recommended to serve as backup power.
3.4Please don’t disassemble alarm host at will so as not to cause accidents or
damage the apparatus.
3.5If failure occurs during operation, please carry with warranty card to contact
with Karassn client service department or Karassn agents. Remember not to
disassemble or repair it by yourself.
3.6Please periodically perform test so as to clear troubles in time to avoid