Karassn KS-200B Series User Manual - page 6
100-Zone Wireless Alarm System
-
5
-
omitting alarm signals.
4. Main Functions And Characteristics
KS-200B-A Function Introduction
4.1Detector (wireless emitter) can automatically learn codes with alarm host.
And dilatancy is easy and quick.
4.21-100 independent wireless defense area can be defined and the defense of
each defense area can be activated or deactivated independently. Common defense
area and emergent defense area can be defined at will.
4.3Alarm host has two groups of timer-open time and two groups of timer-close
time, and it indicates present time.
4.4Three kinds of alarm sound and four levels of alarm volume are optional.
4.5Ten pieces of up-to date alarm messages can scroll to display simultaneously.
4.6The 60 pieces of latest alarm message can be inquired.
4.7Build-in backup battery is optional. And it equips with floating charge device,
and it indicates when battery power lower.
4.8A set of normal open output, a set of normal close output and +12V DC output
are provided to control other devices (e.g. startup alarm siren, alarm light, alarm
linkage and etc.)
KS-200B-B Function Introduction
Based on KS-200B-A host, KS-200B-B host increases functions as following:
* It can automatically dial six groups of alarm telephone numbers and two
groups of pager numbers when alarming.
*The system dailer with distinguish function.
*It rushes to inform you the alarm message by cutting your speaking on the
telephone.
*Dailing pause function.
*Record 20 seconds alarm sound preset.
*Telephone short or cut report function can be opened/closed.
5. Name And Usage Of Main Parts
5.1 KS-200B-A/B Alarm Host
1
、
“ ” key: It is used to complete setup function together with “Function” key.
2 “Function” key: Press “Function” key to switch between setup functions.
、
100-Zone Wireless Alarm System
-
20
-
Precautions:
1.Please don’t press emergency button on remote controller to trigger the detector
when learning code.
2.For being transmit code of detector, the code signal alarm host receives should
be transmit by emitter (transmitter).
3.To avoid wrongly learning code, please trigger detector to test to see if the code
has been learned successfully.
For example:
Learning a detector in zone 2, set it to be emergency zone type.
Firstly, turn detector on, power alarm host off. Press “Function” Key, at the same
time, power alarm host, then release “Function” Key. It will show “01 : 0- 09”.
Press “
” key to select the zone number 02, The screen will show “ 02 : 0- 09.
Press “
>
” key, it will show 02 : 1- 09. Then press “Function” key and trigger the
detector to emit. It will make two indicative “beep, beep” sound, and “–” (middle
line) will change to “_” (under line), which means the setting is successful.
10. How To Set Transmit Function
KS-200ATI, BTI detector support wireless transmitting which can transmit 315
MHz detectors produced by our company (e.g., wireless door sensor, wireless
infrared detector, wireless smoke detector and so on)
Transmit Regulations
If the address code transmitted by transmitter is the same as that of 315MHz
detectors, transmitter will transmit VD5026 code signal to KS-200B alarm host.
Detector transmit signals according to the address code, so the address code of
transmitter should be the same as that of 315MHz detector. A transmitter can
transmit the alarm signal of several315MHz detectors, the quantity is unlimited in
theory.
Each KS-200ATI/BTI detector (transmitter) has 4 bits transmit address code. that
is D0,D1,D2,D3 and each address code has four states, that is “OTH, 1TH, 3TH,
4 TH” as picture 1
Picture 1
3TH
4TH
1TH
D0 D1 D2 D3
3TH
4TH
1TH