Karassn KS-200B Series User Manual - page 12
100-Zone Wireless Alarm System
-
11
-
installed in the locations where have Hazard Gases Of Class I, II or III ( i.e. have
certain thickness of flammable gas, explosive steam gas, dusts, fibers and etc).
Otherwise, it is very dangerous.
*In order to ensure the receive effect of radio signal, neither should the alarm
host share the same power supply with TVs, micro ovens and other electric
appliances with high radiation nor close to these electric appliances. At the same
time, the radio antenna should be pull out.
8.Operation Guide
8.1Warning Sound
(1)KS-200B-A Alarm Host
A long “beep” sound when it is powered on, which means self-test of system is
normal.
Two short “beep, beep” sounds every 30 seconds, which means battery power
lower.
(2) KS-200B-B Alarm Host
A long “beep” sound when it is powered on, which means self-test of system is
normal.
Two short “beep, beep” sounds every 30 seconds, which means battery power
lower.
A short “beep” sound every second, which means alarm caused by telephone
line cut-off.
(3) Wireless Infrared Detector (Wireless Emitter)
Two short “beep, beep” sounds every 30 seconds, which means battery power
lower.
A short “beep” sound, which means armed by remote controller is effective.
Two short “beep, beep” sounds, which means disarmed by remote controller is
effective.
8.2 How To Program KS-200B-A and KS-200B-B
After powered on, the display screen of alarm host shows “12:00 00”. The
second light is flashing and the last two bits display second. Press “Function”
key to enter setup state, at the same time, the second light is continuously on and
the last two bits are flashing, which is the function menu. At this time, the alarm
host won’t receive any alarm signals of detector. In setup state, press “Function”
key to switch among functions. And press “Reset” key to exit the setup state. In
100-Zone Wireless Alarm System
-
14
-
turn-off state.
(6)How To Set Arm/Disarm In Different Zones
Press “Function” key, It displays as below:
Zone No: press Zone state press Function 6
key to set key to set Zone state
After entering “Arm/Disarm” setting state, press “ ” key to select the zone
number and press “
” key to select arm/disarm state. “00” means this zone is
disarmed, “01” means this zone is armed. It should be noted that, no matter the
defense zone is common zone or emergency zone, all the alarm signals won’t be
received if it is disarmed by alarm host.
The default factory state is that all defense zones are armed.
It is recommended to recover the defense state in time when a defense zone is
disarmed so as not to omit any alarms.
(7)How To Inquire Logs
Press “Function” key, it displays as following:
Alarm Record Alarm Function 7
No. location Alarm record inquiry
Enter “alarm record inquiry” state, press “
” key to display alarm record number
and alarm location, press “ ” key to display alarm time, If there are no alarm records,
it will display like “------”.
Alarm time Alarm time Function 7
Hour Minute Alarm record inquiry
Press “ ”again to display the record number and the alarm location of the previous
alarm record. Continuously press “ ” to display the alarm time of the previous
alarm record.
(8)How To Set Alarm Sound And Alarm Volume
Press “Function” key , it displays as following:
alarm sound selection alarm volume selection Function8
Press “ ” to set Press “ ” to set Alarm sound/volume setting
Enter function 8 to set alarm sound and alarm volume. press “ ” to select alarm
sound and press “ ” to select alarm volume.
There are three types of alarm sound. “01” is 110 police car warning sound, “02”
>
>
>
>
>
>
>