1. DL manuals
  2. Makita
  3. Saw
  4. EA3200S
  5. Technical Information

Makita EA3200S Technical Information

Summary of EA3200S

  • Page 1

    Product c oncept and main applications p 1/ 15 s pecification s tandard equipment note: the standard equipment for the tool shown above may vary by country. Model no. Ea3200s, ea3201s, ea3202s, ea3203s description petrol chain saws models ea3200s, ea3201s, ea3202s and ea3203s are entry class petrol ...

  • Page 3

    P 3/ 15 (1) remove sprocket guard, guide bar and saw chain from machine. (2) insert small-slotted screwdriver into the gap between crank shaft and retaining ring e type 6, and then twist retaining ring e type 6 using the slotted blade. (fig. 4) (3) remove flat washer 8 and retaining ring e type 6 fr...

  • Page 4

    P 4/ 15 (1) remove sprocket guard, guide bar and saw chain from machine. (2) remove clutch drum assembly. (figs. 4 and 5) (3) turn hand guard toward chain bar top side to operate chain brake. Note: this allows the tension of brake guard to be relaxed. (4) remove two 3x10 tapping screws and brake cov...

  • Page 5

    P 5/ 15 (1) remove sprocket guard, guide bar and saw chain from machine. (2) unscrew m5x40 hexalobular socket head bolt and two m5x16 hexalobular socket head bolts as drawn in fig. 9, and then disassemble muffler section as drawn in fig. 10. Assemble the components of muffler section by reversing th...

  • Page 6

    P 6/ 15 (1) remove sprocket guard, guide bar and saw chain from machine. (2) pull hand guard toward tubular handle to release chain brake. Then, remove “clutch drum assembly”. Refer to [2]-2. (3) set 1r396 on clutch and turn it clockwise using cordless impact driver with 19mm socket bit. (fig. 11) n...

  • Page 7

    P 7/ 15 (1) remove clutch drum section and clutch section. Refer to [2]-2 “clutch drum section” and [2]-5 “clutch section”. (2) remove tension spring 10. Refer to [2]-3 “chain brake section”. (3) remove pump drive from crank shaft while sliding pump drive back and forth slowly to disengage with gear...

  • Page 8

    P 8/ 15 (1) remove sprocket guard, guide bar and saw chain from the machine. (2) remove “recoil starter section”. See [2]-7 “recoil starter section”. (3) remove spark plug and set 1r372 into the hole for spark plug to prevent crank shaft from being turned together with m8x1 hex nut in the next step....

  • Page 9

    P 9/ 15 note: drain fuel tank before disassembling carburetor. See fig. 22. (1) remove hood. (2) turn choke lever to the position of “stop”. (3) remove two m4x40 hexalobular socket head bolt on intake manifold. (4) remove air filter cover, air filter, and intake manifold. (5) remove one end of tube ...

  • Page 10

    P 10/ 15 (2) check the following points. • intermediate flange is inserted into the groove on engine housing complete. • when cylinder comes into engine housing complete, pulse tube end and red tube end are placed on the position to connect with carburetor. (fig. 26) • before fastening cylinder to c...

  • Page 11

    P 11/ 15 see figs. 28 and 29 for the positions of needle-idle (l) and needle-high speed (h). Carburetor has two different specifications (walbro-made and zama-made). After tightening each needle to the full, loosen them as listed below. Fig. 28 fig. 29 r epair needle adjustment pressure test general...

  • Page 12

    P 12/ 15 unscrew 5.5x16 hexalobular tapping screw and pull grip shell half slightly up and toward the screw hole side.(fig. 32) note: when disassembling throttle lever: (1) remove sprocket guard, then remove two compression springs 12 and four 5.5x16 hexalobular tapping screws on a and b sides. (fig...

  • Page 13

    P 13/ 15 (1) referring to “disassembly of [2]-11. Tank assembly”, disassemble the machine as drawn in figs. 34 and 33. (2) using long-nose pliers, carefully pull out the one end of fuel line from fuel nipple. (refer to figs 37 and 28) note: connect the one end of fuel nipple to 1r127 (refer to fig. ...

  • Page 14

    P 14/ 15 (1) remove “air filter, carburetor, and intermediate flange” as mentioned in [2]-10. (figs. 22, 23, 24, and 25) (2) piston set can be separated from crank shaft by removing ring spring 8 from piston with long-nose pliers. (fig. 38) note: supply 2-stroke engine oil to piston and the inside o...

  • Page 15

    [3] tightening torque fastening for crank case underside 266608-2 4 5x40 hexalobular tapping screw part no. Of screw/ bolt/ clutch description quantity fastening torque (n.M.) 10 ± 0.5 intermediate flange 266651-1 2 5.5x16 hexalobular tapping screw 4 ± 0.5 muf fler base (the component of muf fler co...